FILE: 091-73-XXX.P65
4-23-2002
REV. B
INSTRUCTION MANUAL
SUPER 30 AUTO EJECT
AUTOMATIC SHORE LINE DISCONNECT
30 AMP
MODEL # 091-73-XXX
1 YEAR WARRANTY
KUSSMAUL ELECTRONICS CO., INC.
170 CHERRY AVE., WEST SAYVILLE, N.Y. 11796
TEL: in NY 631-567-0314 TOLL FREE: 800-346-0857 FAX: 631-567-5826
INSTALLATION INSTRUCTIONS
1. Locate a convenient place on the vehicle to mount the AUTO EJECT. A minimum clear
ance of 4 1/2 inches behind the mounting panel is required.
2. Place the template in position and center punch in 6 places.
3. Drill 1 key way hole, 3/8" diameter. IMPORTANT THIS HOLE MUST BE DRILLED FIRST.
3. Drill 4 mounting holes, 3/16" diameter, 1 switch hole, 15/32 diameter and 1 hole, 2 1/4"
diameter. Be certain that all the holes are precisely located to insure that no binding
occurs when the receptacle is moved in and out.
4. Remove the 4 #6-32 screws from the terminal side cover. The terminal cover must be
drilled to accommodate the strain reliefs or conduit fittings. No holes have been provided
so that the installer has complete freedom as to there location. Two inputs are suggested,
one for the A.C. power wiring and the other for the D.C. control wires.
5. After wiring reinstall the terminal cover with the gasket and the 4 screws previously re
moved.
6. Install the large rubber gasket over the AUTO EJECT and mount on the vehicle utilizing
the weatherproof cover, cover gasket and four #8-32 screws provided.
7. Install the rubber boot on the pushbutton switch.
8. Wire the A.C. leads to the appropriate loads in the vehicle and the D.C. wires as
indicated in the diagram. Note that the Auto Eject requires a continuous supply of Battery
voltage and ground in addition to the connection to the starter. No power is drawn from
the battery circuit unless the Auto Eject is operated.
TEST AND OPERATION
The Super 30 Auto Eject disconnects the shore line by retracting its male pins and
housing into the vehicle. To install the shore line, momentarily depress the
pushbutton switch. This will partially extend the male assembly. At this point the
interrupter switch has not closed and the power cannot flow into the vehicle. Open
the end of the shore line connector and insert onto the male pins of the AUTO EJECT.
Now depress the pushbutton a second time and hold till the connector is fully extended. This will close the interrupter switch and power is now applied to the
vehicle’s A.C. loads. Next, push in on the shoreline connector until it is fully seated.
NOTES AND CAUTIONS
NOTE
Do not permit the shore line to drop to the floor when it is ejected. Keep from falling
by utilizing a bungee cord restraint, cord reel or some other device. Dropping the
connector may result in damage or breakage. Kussmaul Electronics does not warrant
the IEC 309 connector.
ABOUT CONNECTORS
The Super 30 Auto Eject utilizes an IEC 309 mating connector. We suggest that you
utilize the connector supplied. When replacing with another connector, test carefully
that the new connector will eject properly.
IMPORTANT
YOU MUST INSTALL A FUSE BETWEEN THE BAT-
TERY + TERMINAL ON THE SUPER 30 AUTO EJECT
AND THE BATTERY. FAILURE TO DO THIS WILL VOID
THE WARRANTY.
CAUTION
THE EXTEND PUSHBUTTON SWITCH MUST BE
PUSHED ONLY MOMENTARILY TO EXTEND THE AUTO
EJECT TO THE FIRST POSITION TO RECEIVE THE
SHORE LINE. IF THE PUSH-BUTTON IS HELD DOWN,
THE AUTO EJECT WILL EXTEND FULLY AND DEFEAT
THE INTERRUPTER SWITCH.
HOLE TEMPLATE
1 YEAR WARRANTY
All Super 30 Auto Ejects manufactured by Kussmaul Electronics Company
Inc. are warranted to be free of defects of material or workmanship. Liability is
limited to repairing or replacing at our factory, without charge, any material or
defects which become apparent in normal use within 1 year from the date the
equipment was shipped. Equipment is to be returned, shipping charges prepaid
and will be returned, after repair, shipping charges paid.
This warranty does not include normal wear and tear, pitting of the electrical
contacts, malfunction due to contamination of the mechanism, or any cracking
breakage or damage to the IEC 309 connector.
Kussmaul Electronics Company, Inc. shall have no liability for damages of any
kind to associated equipment arising from the installation and /or use of the
Kussmaul Electronics Company, Inc. products. The purchaser, by the acceptance
of the equipment, assumes all liability for any damages which may result from its
installation, use or misuse, by the purchaser, his or its employees or others.
Loading...