KUSSMAUL AUTO CHARGE 11DV Instruction Manual

Page 1
BOOK# 091-11DV-1
rev.A: 8-30-05
INSTRUCTION MANUAL
AUTO CHARGE 11DV
AUTOMATIC BATTERY CHARGER
MODEL #091-11DV
INPUT :115 or 230 volt, 50/60 Hz, 2amps
OUTPUT : 11 AMPERES D.C.
KUSSMAUL ELECTRONICS CO., INC.
170 CHERRY AVE., WEST SAYVILLE, N.Y. 11796
TEL: in NY 631 567-0314 TOLL FREE: 800 346-0857 FAX: 631 567-5826
NOTE :
This charger is designed for
and negative ground.
3 YEAR WARRANTY
Page 2
INTRODUCTION
The Auto Charge 11DV Battery Charger is a compact completely automatic charger designed for installation on vehicles with two batteries. An internal charge divider charges both batteries simultaneously while maintaining battery isolation. Remote sensing permits long lines between the charger and the batteries by compensating for the voltage drop in the charging wires. An ammeter provides continuous indication of the charger output. Input power may be either 115 volts or 230 volts . A voltage selector switch is provided on the end panel near the output terminal strip.
Construction of the Auto Charge 11 is extremely rugged to withstand the shock and vibration normally encountered by vehicle mounted equipment. The unit operates completely automatically and stops charging the batteries when they are fully charged. There is no trickle charge and therefore no danger of overcharging and water boil-off. Any parasitic loads on the battery such as radio, lights, etc., are automatically supplied with current by the
charger.
INSTALLATION
The Auto Charge 11 Automatic Battery Charger should be installed in an area with adequate ventilation. A power cord is supplied for connection to 115 or 230 volts 60 Hz.
1. Mount the charger using the four holes provided for this.
2. Connect the wiring from the batteries to the Output Terminal Strip. Spade lugs that have been securely crimped, or soldered, should be used.
3. Connect the wiring to the batteries. Ring lugs that have been securely crimped, or soldered, should be used.
4. Double check all wiring before proceeding.
5. Wire the A.C. power line cord to 115 or 230 volts.
6. Pilot light will light to show that the charger has power.
Page 3
INSTALLATION WIRING DIAGRAM
g
115 or 230 voltage se­lector switch.
NOTE:
Do not apply 230 volts to the charger with the se­lector switch in the 115 volt position serious dam­age may result
3 AMP
FUSE
INPUT
LN
OUTPUT
BAT 1 BAT 2
Optional Bar­Indicator 091-11-127
POWER
REMOTE
raph
Y
E
L
L
O
W
B
L
A
C
K
R
E
D
Optional Economy Indicator
A.C. Input Power
Line
Neutral Ground
IMPORTANT: Charger output wire size is 14 awg. Wire size is for a maximum length of 20 feet. If wiring is to be longer, larger wiring is required. Additional information is available on request.
Chassis Ground
Chassis
Ground
091-11-102-XX
Chassis
Ground
Page 4
SPECIFICATION & OUTLINE
SPECIFICATIONS: Input: 115V or 230V 50/60Hz,
2 amps, switch selectable
Output: see chart Output Current: see chart Charge Indicator: 0-15 amps 5% Weight: 12 lbs
9/32" DIA.
SPECIFICATION CHART
MODEL # AMPS VOLTAGE
091-11DV-6 12 6 091-11DV-12 12 12 091-11DV-24 6 24 091-11DV-POS 12 12
4.375
5.50
10.375
OUTLINE DRAWING
11.375
4.375
Page 5
INSTALLATION RECORD & WARRANTY
Date Installed
Installed By
Vehicle Identification
Vehicle Owner
W ARRANTY
All product of Kussmaul Electronics Company Inc. are warranted to be free of defects of material or workmanship. Liability is limited to repairing or replacing at our factory, without charge, any material or defects which become apparent in normal use within 3 years from the date the equipment was shipped.
Kussmaul Electronics Company, Inc. shall have no liability for damages of any kind to associated equipment arising from the installation and /or use of the Kussmaul Electronics Company, Inc. products. The purchaser, by the acceptance of the equipment, assumes all liability for any damages which may result from its installation, use or misuse, by the purchaser, his or its employees others.
Loading...