Page 1
FILE: 091-53-12-REMOTE
DATE: 12-16-2005
REV: C
INSTRUCTION MANUAL
AUTO CHARGE
1200
REMOTE
AUTOMATIC BATTERY CHARGER
MODEL #091-53-12-REMOTE
INPUT :115 volt, 50/60 Hz, 10 amps
OUTPUT: 40 AMPERES
3 YEAR WARRANTY
KUSSMAUL ELECTRONICS CO., INC.
170 CHERRY AVE., WEST SAYVILLE, N.Y. 11796
TEL: in NY 631-567-0314 TOLL FREE: 800-346-0857 FAX: 631-567-5826
Page 2
INTRODUCTION
The AUTO CHARGE 1200 is a compact, completely automatic, single channel
battery charger designed for vehicles with a single battery system. The charger is
ruggedized to withstand the shock and vibration encountered by vehicle mounted
equipment.
The battery charger features:
• Electronic remote sensing of true battery voltage, eliminates the need
for sensing wires
• Automatic current limiting
• Battery charge/condition indicator
• Power “ON” LED indicator
Charge Controls & Electronic Remote Sensing
The Auto Charge 1200 contains a precision voltage controller to maintain the
battery’s charge. Automatic electronic remote sensing measures the true battery
voltage, eliminating the need for the additional sense wires. The output current of
any charger is inherently a series of pulses whose frequency is determined by the
power line frequency. Therefore there are brief intervals during which no charging
current flows. During this brief interval the Auto Charge 1200 measures and stores
the battery voltage. This battery voltage is compared to a standard and any error is
detected and used to control the charger output at the desired level. Their is no
“trickle charge” and therefore no danger of overcharging and water boil-off.
Page 3
Automatic Current Limiting
When batteries are severely discharged, some battery chargers can be overloaded
due to the high charging current required. The Auto Charge 1200 contains an
automatic current limit. This circuit limits the output current to the rated 40 amperes
when charging a deeply discharged battery or if the starter cranks the engine while
charging. The current limiter thus eliminates the need for an ignition interlock
circuit.
Battery Charge Condition Indicator
This indicator shows the charge condition of the battery in 10 levels from “LOW
CHARGE” to “FULLY CHARGED”. This device indicates a defective battery when
a bar graph does not rise to the “FULLY CHARGED” level after an extended period
of charging.
NOTE: If a battery is being charged with an external load of 4 to 10 amperes
across it’s terminals, the bar graph may move down 1 or 2 levels. This
does not indicate a defective battery.
Page 4
Installation Wiring Diagram
NOTE INDICATOR WIRING
PIN 1 OF INDICATOR MUST GO TO PIN 1
OF CHARGER, PIN 2 OF INDICATOR MUST
INDICATOR
GO TO PIN 2 OF CHARGER AND SO FORTH
PLEASE CHECK CONNECTIONS AND COLOR
OF WIRES BEFORE PLUGGING IN.
AUTO CHARGE 1200
REMOTE DISPLAY
BLKWHT
RED
POWER
FUSE
Chassis
Ground
USE 8 AWG
or larger on
Output & Gnd
OUTPUT
+
IMPORTANT: WIRE SIZE IS
FOR A LENGTH OF 10 FEET.
IF WIRING IS TO BE LONGER,
6 AWG WIRING IS REQUIRED,
ADDITIONAL INFORMATION IS
AVAILABLE ON REQUEST.
Chassis
Ground
Page 5
Specifications:
Input:
Input Fuse: 15 ampere, fast acting
Output: 12 volts D.C. 40 amperes Max.
Remote Sensing: Electronic, sense wires not required
Indicators: Power: Red LED, indicates 115 volts power applied
Weight: 21 lbs
115 volt, 50/60 Hz, 10 amperes
Bar Graph: indicates charger output and state of charge of
battery
Outline Dimensions, AUTO CHARGE 1200
Page 6
INSTALLATION RECORD & WARRANTY
Date Installed
Installed By
Vehicle Identification
Vehicle Owner
WARRANTY
All products of Kussmaul Electronics Company Inc. are warranted to be
free of defects of material or workmanship. Liability is limited to repairing or
replacing at our factory, without charge, any material or defects which
become apparent in normal use within 3 years from the date the equipment
was shipped. Equipment is to be returned, shipping charges prepaid and will
be returned, after repair, shipping charges paid.
Kussmaul Electronics Company, Inc. shall have no liability for damages
of any kind to associated equipment arising from the installation and /or use
of the Kussmaul Electronics Company, Inc. products. The purchaser, by the
acceptance of the equipment, assumes all liability for any damages which
may result from its installation, use or misuse, by the purchaser, his or its
employees or others.
Loading...