Kushlan Products 600 Gas User Manual
Operating Instruction and
Parts Manual for
350/600 Gas
Gas Model Series With
Optional Tri-Pod Stand
WARNING
DO NOT ATTEMPT TO START OR OPERATE THE
MACHINE UNTIL ALL THE INSTRUCTIONS HAVE
BEEN READ AND UNDERSTOOD BY THE OPERATOR.
FAILURE TO DO SO COULD RESULT IN SERIOUS
BODILY INJURY AND/ OR PROPERTY DAMAGE!
12010 Dairy Ashford Road, Suite 160
Sugar Land, TX 77478
281-313-2506 • 800-469-4178
SHOULD YOU REQUIRE ANY
SET-UP OR OPERATING ASSISTANCE WITH YOUR PRODUCT,
DO NOT RETURN TO ORIGINAL PLACE OF PURCHASE
•Aer referring to the operation manual, if assistance is still needed, please consult our web Site at
www.kushlanproducts.com
• From our web site you may e-mail us directly If assistance is still required, please call our customer service
department at 1-800-469-4178
Safety Alert Symbol: is safety alert symbol is used to attract your attention!
• Personal Safety is involved when you see this symbol, Pay extra attention, become alert-be sure to heed it’s message.
Failure to do so may lead to serious personal injury or damage may occur.
• Warnings and safety instruction: If these warnings and safety instructions are not read and carefully followed, serious
personal injury could occur.
WARNINGS
1. Do not use, start, or attempt to operate this machine until all of the instructions have been read and fully understood.
2. Never allow anyone to operate this machine unless the person is well acquainted with these rules of safe operation.
3. Never operate this machine without all guards in place and rmly attached to the machine.
4. Make certain that the mixing drum is clear of obstructions and stand clear of the machine with out all guards in place and rmly attached to the machine.
5. When cleaning, lubricating, or adjusting the mixer, disconnect the power plug.
6. Keep all people (except operator) a minimum of ve (5) feet away from the machine during operation.
7. Always make certain that the mixer is connected to a properly grounded electric circuit to protect the operator from possible electric shock.
8. Do not start the engine if the drum is Fully loaded
9. Do not overload the mixer
10. Never attempt to move the mixer while the engine is on.
2
SAFETY INSTRUCTIONS For the safety of yourself and others around you, it is extremely important that you observe the following notes.
1. Keep hands and clothing away from moving parts at all times.
2. Do not operate this machine under the inuence of alcohol or while taking medication that impairs the senses or reactions.
3. Make certain that the work area around the machine is clear of debris and obstructions.
4. Keep all unauthorized and untrained people away from the machine at all times.
5. Never let the mixer run unattended even for a brief moment.
6. Turn o the engine when you leave the machine.
7. Only use or operate the mixer on level ground to prevent the mixer from tipping over.
8. Do not overreach while working with the mixer. Keep proper Footing and balance at all times when loading or unloading the mixer.
9. Never allow children or inexperienced operators to operate or repair the mixer.
10. Use only factory authorized parts for replacement
11. Keep these operation instructions with the machine at all times
12. Always wear safety glasses and safety shoes when operating and moving equipment
13. Safety decals – replace missing damaged safety decals.
Mixer Instructions
A. LUBRICATION: ere are grease ttings (item 29) on all models. Apply any type of EP grease. Apply grease until grease begins to come out of the
bearings. LUBRICATE ALL FITTINGS BEFORE EACH USE
B. GEAR ADJUSTMENT: If the gear on the jacksha (item 13A) is not meshing properly with the ring gear and plate (17), adjustment can be made by
loosening the hex ange screws at attaching the jacksha housing (14A) and sliding the housing tube until proper alignment is obtained. If removal of
pulley guard is necessary, make certain it is reattached to the machine before using.
C. GENERAL: Check all screws for tightness before each use.
D. ENGINE ADJUSTMENT/BELT TENSIONING: 1. To adjust belt tension. Loosen the 2 bolts that attach the engine to the frame. Make adjustments
and retighten screws. 2. V-BELT TENSIONING: Retighten V-belts aer the rst 20 hour of use. e belt should be tightened until the belt deects
approximately 1/4” with regular thumb pressure. 3. Replace covers and guards before using the machine.
E. CONCRETE MIXING: Do not insert sharp objects into the plastic mixing drum. Doing so will damage the drum.
F. CLEANING: Do not spray water on or into the motor. orough cleaning of the mixer aer each use is recommended and will add to the service life.
Model 350GAS & 350GAS With Stand Parts List
3
ITEM PART NO
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
35-1
35-2
35-3G
35-4
35-5
35-6
35-7
35-8
35-9
35-10
35-11
35-12
35-13
35-14
35-15
35-16
35-17
35-18
35-19
35-20
35-21
35-22
35-23
35-24
35-25
35-26
35-27
35-28
35-29
35-30
35-31
35-32G
35-33G
35-34G
35-35G
35-36G
35-37
35-38
35-39
35-40
35-41
35-42
35-45G
35-46
35-47
35-48
35-49G
35-50G
35-60G
DESCRIPTION
Frame assembly
Polyethylene 3.5 cf drum with side holes
Gas Engine
1 1/2" pulley
28" V-belt
6" pulley
Jacksha with pinion
Jacksha housing
1/2 Ball Bearings
1/2" X 20 thread nut
3/16'' square key
Ring gear & plate assembly
Drum plate & sha assembly
Drum sha bushing
1" locking collar
Wheelbarrow handle
Handle grip
350WSB mixing blades
Poly ring gear guard
Guard for Pulley
Grease tting
3/8" x 1-1/4" whizlock screw
Whiz lock nut 3/8"
Whiz lock nut 5/16"
1" Metal thrust washer
Wheelbarrow axle
Axle spacer tube
300 x 8 Wheel
Locking pin/lanyard
Whizlock screw 5/16 x 3/4"
Whizlock screw 3/8 x 3/4"
Gas Engine Cover
Power kill switch
Whizlock Screw to install Gas Engine 6x35mm
Whizlock Screw to install Gas Engine 6x70mm
Spring Washer for Whizlock Screws
Support brace
Vertical Pipe Support
Horizontal rest bracket
Leg support 1 pipe
Leg support 2 pipe
Whizlock screw
Parts book
5/8'' Washer
" R '' Clip for washer
Wheel Bearing for 300 x 8 Wheel 16 x 22 (mm)
Mounting Plate for Gas Engine
Centrifugal clutch
Ratio 6:1 Gear box
QTY
1
1
1
1
1
1
1
1
2
1
1
1
1
2
1
2
2
2
1
1
2
12
15
11
1
1
1
2
2
11
3
1
1
5
2
7
1
1
1
1
1
2
1
2
2
4
1
1
1
Loading...