Z O M B I E W I N D S H I E L D T R I M 1 1 9 8
FIT S : ’ 9 6 - U P FLHT, F L H T C , F L H TCU, FL H X
PARTS INCLUDED
1 Zombie Windshield Trim
1 Hardware Kit Including:
2 1/4” Flat Washer
1 1/4”-20 x 5/8 Socket Button Head Cap Screw (SBHCS)
2 1/4”-20 x .625” Knurled Spike Fasteners
2 1/4”-20 x 1” Knurled Spike Fasteners
1 Zombie Emblem
1 Installation Instructions
Please read and understand entire instructions before starting installation.
THANK YOU FOR CHOOSING KÜRYAKYN!
IN ORDER TO PROTECT YOU AND OTHERS FROM POSSIBLE INJURY
AND/OR PROPERTY DAMAGE OR LOSS, PLEASE PAY CLOSE ATTENTION
TO ALL INSTRUCTIONS, WARNINGS, CAUTIONS AND ATTENTION NOTES
REGARDING THE USE AND CARE OF THIS PRODUCT.
WARNING! THIS INDICATION ALERTS YOU TO THE FACT THAT IGNORING THE
CONTENTS DESCRIBED HEREIN CAN RESULT IN POTENTIAL DEATH OR
SERIOUS INJURY.
CAUTION! This indication alerts you to the fact that ignoring the contents described
herein can result in potential injury or material damage.
ATTENTION!This indication alerts you to the fact that ignoring the contents
described herein may negatively affect product performance and
functionality.
TOOLS SUGGESTED
Set of hex wrenches, Torx wrenches, combination wrenches
STRICTLY OBSERVE THE FOLLOWING GUIDELINES IN ORDER TO USE
THE PRODUCT PROPERLY AND AVOID POTENTIALLY DANGEROUS
ACCIDENTS.
NOTE; IF INSTALLING WINDSHIELD TRIM
ON KüRYAKYN® AIRMASTER™ FAIRING,
USE THE 1/4”-20 X 1” KNURLED SPIKE
FASTENERS.
PIC.1
I N S TA L L AT I O N
CUSTOMER SERVICE
877.370.3604 (toll free)
INSTALLATION QUESTIONS
techsupport@kuryakyn.com
or call 715.247.2983
Küryakyn warrants that any Küryakyn products sold
hereunder, shall be free of defects in materials and
workmanship for a period of one (1) year from the
date of purchase by the consumer excepting the
• Küryakyn shall have no obligation in the event
the customer is unable to provide a receipt showing
the date the customer purchased the product(s).
maintained and operated under normal conditions.
implied, with respect to any gold plated products.
• Küryakyn shall not be liable for any consequential
paint, resulting from failure of a Küryakyn product,
failure to deliver, delay in delivery, delivery in non-
conforming condition, or for any breech of contract
• Küryakyn products are often intended for use
• Küryakyn electrical products are warranted for
one (1) year from the date of purchase by the con-
sumer. Components of Küryakyn products containing
L.E.D.s will be warranted for defects in materials and
workmanship for 3 years from the date of purchase.
regard to other manufacturer’s products distributed
by Küryakyn. Küryakyn will pass on all warranties
made by the manufacturer and where possible, will
but ultimately, responsibility for disposition of the
online today–select the ”CATALOGS” icon. Each
Küryakyn® product comes with a Proof-of-Purchase
©200 5 Kür yakyn USA® All Right s reser ved.
LIMITED WARRANTY
following provisions:
• The product must be properly installed,
• Küryakyn makes no warranty, expressed or
and incidental damages, including labor and
or duty between Küryakyn and a customer.
in specific applications. Küryakyn makes no
warranty if a Küryakyn product is used in
applications other than intended.
• Küryakyn makes no warranty of any kind in
expedite the claim on behalf of the customer,
warranty claim lies with the manufacturer.
ABOUT OUR CATALOG
You’ll find all our innovations for H-D, GL and
Metric Cruisers in our annual catalogs. Order
good for a complimentary catalog. Details in
Be sure to a sk your loc al deale r abo ut
other Kür yakyn pro ducts, t he motorc ycle
par ts a nd accessorie s des igned for r ider s
packaging.
by riders .
PROCEDURE
STEP 1 Park the motorcycle on a hard, level surface;
turn off the ignition.
1198-12HD-0209
REM O V E T H E S E
THR E E T O R X
HEA D S C R E W S
STEP 2 Remove the three Torx head screws that secure the windshield shown in PIC.1. Set these
aside, they will not be used again.
STEP 3 Place the trim in place, lining up the holes in the trim with the holes in the in the
windshield.
STEP 4 Place the 1/4”- 20 x 5/8” SBHCS screw in the center hole without a washer,
do not tighten.
STEP 5 Place the appropriate Knurled Spike Fasteners in the outside holes with
the ¼” flat washers as shown in PIC.2, do not tighten.
SPI K E FASTE N E R W I T H
STEP 6 Tighten the screws, being careful not to over tighten them, which may
damage the trim.
STEP 7 Place the zombie emblem in place with head facing up as shown in PIC.3.
PIC.2
INS E R T K N URLED
THE 1 / 4 ” WA S H E R
PIC.3
PAGE
2
ZOMBIE WINDSHIELD TRIM
INSTALLATION
INSTALLATION
Loading...