Kuppersbusch IW 1476.0W Assembly Instruction

ISTRUZIONI DI MONTAGGIO DELLE

LAVATRICI INTEGRABILI

ASSEMBLY INSTRUCTIONS FOR BUILT-IN WASHING

MACHINES

MONTAGEANLEITUNG FÜR EINBAUBARE-

WASCHMASCHINEN

INSTRUCTIONS DE MONTAGE DES LAVE-LINGE

INTÉGRABLES

INSTRUCCIONES DE INSTALACIÓN DE LAS

LAVADORAS INTEGRABLES

INSTRUÇÕES DE MONTAGEM DAS MÁQUINAS DE

LAVAR ROUPA INTEGRÁVEIS

MONTAGEINSTRUCTIES VAN INTEGREERBARE

WASMACHINES

MONTERINGSANVISNING FOR INTEGRERBARE

VASKEMASKINER

MONTERINGSANVISNINGAR FÖR

INBYGGNADSBARA TVÄTTMASKINER

ANKASTRE ÇAMAŞIR MAKĐNELERĐ

ĐÇĐN MONTAJ TALĐMATLARI

ИНСТРУКЦИИ ПО МОНТАЖУ

ВСТРОЕННЫХ СТИРАЛЬНЫХ МАШИН

ASSEMBLY INSTRUCTIONS FOR BUILT-IN WASHING MACHINES

IMPORTANT - This machine complies with current safety regulations governing electrical appliances and, to ensure user safety, it must be installed by a qualified technician as required by current legislation

Size of cabinet The minimum dimensions of the cabinet are: height 820 mm,

width 600 mm, depth 584 mm (fig. 1).

Applying the panel

Important! Before fitting the panel (removing all the hinge

Warning - To fix the panel on the right-hand side (direction of

Using the template

The panel may be attached to the left- or right-hand side of the washing machine (fig. 2) The machine is supplied fitted for a left-hand side panel attachment as the right-hand side is fitted with the push-pull lock (upper part) and the rubber pad (lower part). Should you wish to use the magnetic lock instead of the pushpull lock, remove the push-pull lock support and fit the supplied magnetic lock support.

and locking elements from the front) make sure the washing machine is totally disconnected from the mains power supply.

opening opposite to that of the door) dismount the push-pull lock (or the magnet lock) from the front of the machine and the rubber pad (fig. 3-A) and fit them on the opposite side (fig. 3- B). All the elements applied to the front of the washing machine must be remounted correctly (no holes must remain open) in order to make it impossible to touch live components inside the machine.

Our company declines all liability for failure to observe the above safety requirement.

1) Measure the height of the kitchen baseboard: the height of

E.g.: for a 100 mm high baseboard, the maximum height of

the wooden panel is obtained by first establishing the height of the kitchen baseboard.

the panel is 720 mm. If the height of the baseboard must be increased, the height of the wooden panel must be reduced.

Applying the panel elements and fixing the panel

Adjusting the hinges

Positioning the washing machine in the cabinet

Place the template of the inner side of the panel and match the height of the baseboard with the lower edge of the panel (fig. 4) using the graduated scale. Make sure the template is horizontally centred with reference to the vertical lines marked at the ends. After placing the template in the correct position, trace the positions of the following holes, pushing in with the tip of your pencil:

• holes for the hinges and hinge screws (fig. 4)

•

holes for fixing the metal plate (if the magnetic lock is used), or the hook for the push-pull lock (fig. 4, A - B)

1) Drill the holes for the hinges (fig. 5), the hook for the pushpull lock (fig. 5), or the metal plate if you decide to use the magnetic lock (fig. 6), and the holes for fixing the hinges (fig. 6).

2) The 13 mm depth of the 2 mm holes, for fixing the hinges and a metal plate for the magnet lock, only applies to the solid wood panel. For the chipboard panel, simply drill the upper coating – fig. 6.

3) Screw the two hinges to the panel (fig. 7)

4) Mount the hook for the push-pull lock or the metal plate for the magnet lock on the side opposite the hinges (fig. 7).

5) Fix the panel to the washing machine following the instructions shown in fig. 8.

If, after applying the panel to the washing machine, it is slightly inclined or off-centre with respect to the front of the machine, correct its position by adjusting the mobile part of the hinges (fig. 9).

Position the washing machine in the cabinet and, if necessary, adjust the feet to level it and lock them with the relative locknut. On appliances with adjustable rear feet, refer to the operator’s manual. To prevent the vibrations generated by the washing machine from being transmitted to the cabinet, make sure the sides and top do not touch the cabinet. There must be a gap of at least 2 mm. The back of the machine must also remain detached from the rear panel.

If the cabinet is 870 mm high, the washing machine heightening kit on sale from the Spare Parts Service, must be used.

To comply with safety legislation, any gaps between the floor and the bottom of the baseplate and between the floor and the sides of the machine when it is positioned at the end of a line of furniture must be completely closed.

The cover must be installed in such a way as to make it

+ 6 hidden pages