Kuppersberg SLIMLUX S 90 GW User manual
TECHNICAL PASSPORT
ПАСПОРТ ТЕХНИЧЕСКОГО ИЗДЕЛИЯ
SLIMLUX S
COOKER HOOD
КУХОННАЯ ВЫТЯЖКА
TECHNICAL PASSPORT
Cooker hood
ENGLISH
Dear customer!
Thank you for choosing the products
of the brand «KUPPERSBERG». We put
with your choice.
1. GENERAL INFORMATION
1.1 Prior to installing the
extractor hood carefully read our
recommendations, following which
will provide safe work of the appliance.
Save this User’s manual, as it contains
answers to the questions which may
arise later.
ATTENTION!
BEFORE STARTING THE OPERATION
(SWITCHING ON) THE APPLIANCE MUST
BE HELD AT THE ROOM TEMPERATURE
FOR AT LEAST TWO HOURS.
1.2. This appliance is intended
for extraction of polluted air from the
space above the cooking appliance,
and intended for domestic use and the
household environment only and meets
the requirements of State EN 60335-
2-2:2010/А11:2012.
ATTENTION!
USE OF THE APPLIANCE IN GOALS
OTHER THAN DOMESTIC IS FORBIDDEN.
THE RISK OF INJURY AND PROPERTY
DAMAGE INCREASES IN CASE OF USE
OF THE EXTRACTOR HOOD WITH
PURPOSES OTHER THAN INTENDED,
WHAT WILL LEAD TO WARRANTY
CANCELLATION/
1.3. Use of the extractor hood
decreases the content of harmful
products of incomplete combustion of
natural gas, as well as odors produced
during cooking in the air, and prevents
pollution of walls, ceiling, and furniture
with grease and soot.
1.4. The appliance is an air purifying
device of the exhaust type with a
diameter fan (turbine), completed
with a grease picking aluminum
is manufactured from sheets of carbon
steel with a decorative protective
coating of powder paints – 600/900 mm
in width.
1.5. Depending on the installation
scheme over the cooker, the extractor
hood can work in two variants:
- in the mode of air extraction into the
stationary ventilation shaft (chimney) of
the kitchen using corrugated aluminum
or plastic air-ducts Ø150mm or Ø120mm
(see item 5.3);
- in the recirculation mode (closed
circular air circulation in the kitchen),
when the extractor hood is not
connected to chimney, and the air is
and is returned to the kitchen (see
paragraph 5.3).
1.6.
ATTENTION!
Do not start extractor hood
installation before connecting it to
electricity network and checking its
technical serviceability, and checking all
of its functions.
1.7. We recommend that all
installation works, connection, and
repair of your extractor hood should
2
ENGLISH
TECHNICAL PASSPORT
1.10.
professionally engaged in the execution
of such works.
1.8. The manufacturer does not
the extractor hood are indicated in this
manual and on the label attached to the
inner surface of the body (access to it
bear responsibility for any damages and
failures, caused by incorrect installation,
operation, and repair of the extractor
hood.
1.9. The manufacturer reserves the
right to modify the product in order
to improve its quality and technical
ATTENTION!
The extractor hood should be
installed on the wall at the distance of
650-750mm above the electric cooker
and at the distance 750-850 mm above
the gas cooker.
2. MAIN TECHNICAL SPECIFICATIONS
MODEL OF KITCHEN EXTRACTOR HOOD SLIMLUX S
Network voltage, V 220-230
AC frequency, Hz 50
Control type Sensor
Number of operation modes 3
Rated power
consumption,
W
Productivity while connecting to standard
ventilation system m
Overall
dimensions of
the extractor
hood, mm
Of the motor 150
Lighting (LED) 2x3
General 156
3
/hour
480 / 650
Width 600 / 900
Depth 300
Height (min-max) 178
Connection size of ventilation duct, mm Ø150 / Ø120
Weight (net), kg 5,9 (600mm) / 7,9 (900mm)
Noise level, dB 61,8 (600mm) / 61,8 (900mm)
Protection class I
Operation mode S1 (long-lasting)
Electro cable type Armoured and grounded
Cooker hood
3
TECHNICAL PASSPORT
Cooker hood
Kitchen extractor hood 1 pcs.
Plastic pipe adapter (from Ø150 to Ø120mm) 1 pcs.
Aluminum grease lter (5-layer)
ENGLISH
3. PARTS SUPPLIED
ITEM QUANTITY
Metric screw М5х35 4 pcs.
2 pcs. (600 mm)
4 pcs. (900 mm)
User’s manual 1 pcs.
4. SAFETY REQUIREMENTS
4.1 При монтаже, эксплуатации и
проведении технического обслуживания категорически запрещается:
• включать вытяжку в электросеть
с напряжением и частотой, которые не
соответствуют указанны
ATTENTION!
IT IS FORBIDDEN TO CONNECT THE
EXTRACTOR HOOD
TO THE NETWORK OF THE ELECTRIC
COOKER. PROTECT ELECTRIC CORD
FROM MECHANICAL AND THERMAL
DAMAGE.
4.1. While installing, the operation
of conducting technical services, it is
strictly forbidden to:
• connect the extractor hood to the
electricity network with a voltage and
frequency that does not correspond to
those specied in paragraph 2;
• use lighting lamps with a power
output of more than 3 Watts (LED);
• carry out maintenance, replace
lamps, remove lters, clean the extractor
hood without removing the plug from
the mains socket;
• operate the extractor hood with
an open re source, open gas burners
or heating elements; Heating elements
should be always covered with dishes;
• prepare food with use of alcohol;
• leave the fryer unattended;
• operate the extractor hood with
removed lters;
• connect the extractor hood to
the electric network of the cooker, cut
the socket of the electric cord while
installing.
ATTENTION!
IT IS FORBIDDEN TO USE GAS
(ELECTRIC) COOKER IF THE EXTRACTOR
HOOD IS TURNED OFF.
4.2. In order to avoid damage by
electric current, the extractor hood must
be plugged into a grounded outlet.
4.3. The extractor hood connected
to the separate ventilation shaft. It is
forbidden to connect other appliances
to the same ventilation shaft.
4.4. Using the extractor hood
together with other heating appliances
(gas, oil, ovens, etc.), besides electric, it
is necessary to provide the premises, it
which the extractor hood is installed
4
ENGLISH
TECHNICAL PASSPORT
Cooker hood
with the additional ow of the fresh air
(for example to open the window).
4.5. For air extraction to the chimney
use air duct Ø150 / 120mm. A smaller
diameter will create additional air
resistance, which will increase noise and
vibration, as well as motor overheating.
4.6. Provide timely cleaning of
non-disposable aluminum removal
lters, otherwise, the efciency of the
extraction will decrease and there will
be a re hazard due to the accumulation
of grease and dust in the lter.
4.7. It is forbidden to turn on the
extractor hood in case of ignition with
the purpose of reduction of smoke until
complete localization of re.
4.8. In case of ignition under the
extractor hood, cover the re with a thick
cloth, disconnect the extractor from the
electric network, do not use water to
extinguish a re in the places where the
electrical appliances are located.
4.9. Protect the cord for connection to
the electric network from the mechanic
and thermal damages.
5. EXTRACTOR HOOD DESCRIPTION
5.1 Ventilation kitchen cooker hood
«SLIMLUX S» is an air-purifying device
of exhaust type with a fan (turbine)
and is equipped with aluminium grease
lter. The product is manufactured in
a single-motor performance with a
width of 600/900 mm from carbon steel
sheet, followed by decorative-protective
coating with powder paints.
5.2 The cooker hood refers to the
type of “built-in pull-out” hoods and
is built into the furniture sets of the
kitchen above the stove.
5.3 Depending on the installation
scheme over the cooker, the extractor
hood can work in two variants (see item
1.5):
- in the mode of air extraction into
the chimney of the kitchen (Fig. 1).
- in the recirculation mode (Fig. 2)
(closed circular air circulation in the
kitchen).
Fig. 1 Fig. 2
Distance H:
To electric cooker 65-75cm
To gas cooker 75-85cm
“It is necessary to consider, that when
the extractor hood is on, the pressure is
automatically lowered in the enclosed
room, and should be balanced with an
inow of fresh air. This may be achieved
by opening doors and windows or with
use of equipment for special inow
ventilation”.
5
TECHNICAL PASSPORT
Cooker hood
Fig. 3
Fig. 3.1
5.4 The cooker hood consists of the
following parts (Fig. 3 / 3.1):
1 – body of a cooker hood
2 – reducing pipe adapter of bubbler
(from Ø150 to Ø120)
3 – electric cord with ground
(protection class - I)
4 – pull-out panel with a lter
5 – decorative glass
6 – switch of operating modes of the
cooker hood (sensory)
7 – aluminium grease lter 1 (2 pcs.-
600 mm, 4 pcs. - 900 mm)
8 – aluminium grease lter 2 (2 pcs.-
600 mm, 4 pcs. - 900 mm)
9 – lighting lamps (LED).
ENGLISH
6. EXTRACTOR HOOD
INSTALLATION INSTRUCTIONS
6.1 This model of the cooker hood
is installed (mounted) on the bottom of
the kitchen closet.
6.2 Remove a cooker hood from the
packing box.
6.3 Check the work of the cooker
hood, connect to the electric mains and
check all its functions.
We remind that the height of
installation of a cooker hood over the
electric cookers should be at least
650mm, and above the gas one – not
less than 750mm (Fig. 1).
6.4 For mounting, an opening for
air outlet and exhaust pipe connection
must be installed and equipped.
6.5 To install the cooker hood in
the kitchen closet, make 4 holes of
6-7 mm in diameter in the lower shelf
of the closet according to g. 4. Fasten
the cooker hood with 4 screws M5х3
(Fig.4.1).
6.6 Connect the bubbler to the
turbine outlet (with pipe adapter of
bubbler Ø150x120mm). Remove the
other end of the bubbler into the
ventilation shaft (Fig. 4 / 4.1).
6.7 If the cooker hood is to operate
in air exhaust mode, mount the bubbler
of the selected diameter in accordance
with the instructions, ensuring that it is
tight.
6.8 If the cooker hood will work in
the recirculation mode, then the bubbler
is not required. It is to be installed
6
ENGLISH
TECHNICAL PASSPORT
Cooker hood
a carbon smoke lter (is purchased
separately).
6.9 Check the reliability of the cooker
hood mounting, feed and connect the
cord to the mains through socket.
In order to provide additional
protection against voltage uctuations
in the network, it is recommended
to connect the extractor hood via an
additional automatic circuit breaker 6A.
Fig. 4
7. INSTRUCTIONS FOR USE OF THE
COOKER HOOD
7.1 The cooker hood with a touch
switch has 3 speeds of ventilation.
Depending on the amount of
evaporation during cooking, you can
choose a low, medium or high of
ventilation level.
7.2 Before cooking, turn on the
hood in the required operating mode.
It is recommended to continue work of
the cooker hood for 3-5 minutes after
cooking, thus the air in the kitchen
will be cleared from the residue of the
vapours.
7.3 On the decorative glass of your
cooker hood there is a touch switch
for operating modes of the engine and
lighting lamps (Fig. 5):
Fig. 5
Fig. 4.1
– on/off lighting
1 speed (low speed) – press the
switch to position “1”
2 speed (average speed) – press the
switch to position “2”
3 speeds (high speed) – press the
switch to position “3”
The touch switch with the symbol of
the light bulb, intended to turn on the
lamp at insufcient illumination of the
working area of the cooker, is located
on the left side of body of the cooker
hood.
7
TECHNICAL PASSPORT
Cooker hood
ENGLISH
Switch on a cooker hood:
- press on any of the speed control
knobs (1, 2, 3) and pull out the pull-out
panel;
- turn on lighting if necessary (button
with bulb symbol), lighting works as
with a closed and open pull-out panel.
Switch off a cooker hood:
- press the speed control knob (1,
2, 3) on the sensor, depending on the
speed at which the cooker hood (11, 2-2, 3-3) works or slide the pull-out
panel.
The switching the hood on and
off with the touch switch is doublepressing, that is, pressing the speed
1 – the cooker hood is switched on,
press speed 1 again – the cooker hood
is turned off. The panel is pulled out –
a cooker hood is turned on, pushed in
the initial position – a cooker hood is
switched off.
Launch timer:
To start the timer, press one of the
touch buttons (1, 2, 3) and hold it for 5
seconds.
The timer will automatically switch
off the cooker hood in 5 minutes.
8. INSTRUCTIONS TO CARE THE
COOKER HOOD
ATTENTION!
BEFORE CLEANING THE COOKER
HOOD, DISCONNECT IT FROM THE
ELECTRIC MAINS.
8.1 For external cleaning of
stainless steel cooker hoods, use special
means in accordance with the relevant
instructions.
8.2 Never use abrasive detergents
and means that contain soda, acid,
chlorides or solvents, coarse sponges to
clean the cooker hoods.
8.3 By washing avoid moisture
entering the current-carrying parts of
the cooker hood, and especially into the
electronic control unit; after washing,
wipe the surface with a soft cloth.
8.4 For cleaning glass surfaces,
conventional glass cleaning means are
suitable.
8.5 The aluminum lter, holding oil
and dust from the air, is clogged and
should be washed after being soaked
in hot water with an effective detergent
once every 1.5 to 2 months. Changing
the color of the lter after washing does
not affect the quality of its work.
8.6 To remove the aluminium
lter (Fig. 6), press the spring lock of
the aluminium lter 1 and remove it.
Extract the pull-out panel with lter
2 and remove the aluminium lter 3.
The lter installation is performed in
reverse order. Do not install the lter
after washing until it is completely dry.
8.7 To replace the lamp, it is necessary
to remove aluminium lter 1, pull out the
panel with the lter 2, pull the holder of
the bulb socket, so that the lamp 3 came
out of the body of cooker hood, holding
the bulb socket, lightly press the lamp
in the direction of the bulb socket and,
turning it counterclockwise, take out
8
Loading...