KUNBUS REVPI CON SE8, REVPI CON SE32 Datasheet

RevPi Connect SE

Article No.: 100368 (8 GB version)
Article No.: 100369 (16 GB version)
Article No.: 100370 (32 GB version)

Technical Data

Housing dimensions (H x W x D) 96 x 45 x 110.5 mm

Housing type DIN rail housing (for DIN rail version EN 50022)

Housing material Polycarbonate

Weight approx. 197 g / 224 g (incl. connectors)

IP Code IP20

Power supply 12-24 V DC -15 % / +20 %, reverse-polarity protected

Max. power consumption 20 Watt (incl. 1 A total USB output current)

Operating temperature -25 °C....+55 °C

1

Storage temperature -40 °C....+85 °C

Humidity (at 40 °C) 93 % (non-condensing)

2 x USB A (Total current draw from both sockets max. 1 A)
2 x RJ45 10/100 Ethernet (using separate MAC addresses)

Interfaces

Connectors

Processor Broadcom BCM2711, quad-core Arm Cortex-A72

Clock rate 1.5 GHz

Processor cooling Passive with heat sink

RAM 1 GB LPDDR4

Flash memory 8 GB (Article No.: 100368) / 16 GB (Article No.: 100369) / 32 GB (Article No.: 100370)

Number of digital input channels 1

Input type 24 V control voltage (e.g. for power-good signal of a UPS)

Input thresholds approx. 3.0 V (0 -> 1) / 2.3 V (1 -> 0)

Input protection against overvoltage, negative voltages

1 x RS485 screw-type terminal (not galvanically isolated)
1 x Micro-USB (solely for image transfer to eMMC)
1 x Micro HDMI HDMI 2.0a (4K)
1 x PiBridge system bus
1 x ConBridge system bus

1 x 4-pole screw-type terminal for relay contact and signal input
1 x 4-pole screw-type terminal for power supply

2

Number of digital output channels 1

1

The average power consumption without USB load varies greatly and depends on the use of the interfaces, the GPU and the CPU. It is usually well below 4 watts without HDMI.

2

1 A USB output current (total of both USB outputs) is only available for input voltag es >11 V. The bridging time of at least 10 ms required by EN 61131-2 is only guaranteed with a 20.4 to 28.8 V

power supply. With a 12 V power supply, this time is signicantly reduced, especially when power is drawn from the USB ports.

KUNBUS GmbH, Heerweg 15C, 73770 Denkendorf, Germany | Tel: [phone] | Fax: [phone] | Email: [e-mail] | Web: www.kunbus.com

page 1/2Errors excepted and possible alterations without prior notice.

Version: EN 1.0

RevPi Connect SE

Article No.: 100368 (8 GB version)
Article No.: 100369 (16 GB version)
Article No.: 100370 (32 GB version)

Technical Data

Output type

Maximum current load of the contact 2 A @ 30V DC (resistive load!)

Software integration of input and output

Hardware watchdog functionality

Hardware watchdog intervall Trigger after approx. 60 seconds without toggling the reset bit.

Compatible modules for system expansion

ESD protection 4 kV / 8 kV (according to EN61131-2 and IEC 61000-6-2)

EMI tests Passed (according to EN61131-2 and IEC 61000-6-2)

Surge/Burst tests Passed (according to EN61131-2 and IEC 61000-6-2)

Buer time RTC min. 24 h

Optical indicator 6 status LEDs (bi-color), two of them freely programmable

RoHS conformity Yes

CE conformity Yes

UL certication

Relay contact, approval up to 30 V switching voltage (e.g. for
power supply of a router)

Via GPIOs and process image. Output is optionally switched by hardware watch­dog.

Can be disabled by bridging the 4-pole screw-type terminal. Reset by toggling a
GPIO or alternatively a bit in the process image.

All RevPi IO modules modules can be connected via the PiBridge system bus.
All RevPi Con modules can be connected via the ConBridge system bus.
! Not compatible with RevPi Gateways !

Yes, UL-File-No. E494534
Note: The device may only be supplied from circuits that comply with Class 2 or
Safety Extra Low Voltage (SELV) according to Class 9.4 of UL 61010-1.

KUNBUS GmbH, Heerweg 15C, 73770 Denkendorf, Germany | Tel: [phone] | Fax: [phone] | Email: [e-mail] | Web: www.kunbus.com

page 2/2Errors excepted and possible alterations without prior notice.

Version: EN 1.0