Kumoh Samsung Gear S3 frontier Normal Security Set, Samsung Gear S3 classic Normal Security Set, Gear S2, Gear S2 classic Installation Manual

(FBS4

GSPOUJFSDMBTTJD

b

g

a

c

Strap buckle

Gear S3

Screw
(Silver)

Caution on the

assembling direction

g

c

Position of screws

to be removed

Gear S3

Caution on the

assembling direction

Array the Charging & security cable( ) into the cable guide of the cradle
properly, insert it into the hole on the table in the direction to the rear side of
the cradle and attach it on the proper position firmly.

Insert the Charging & security cable( ) into the hole on the smart table
while facing downward, and attach the cradle over the hole on the table.

A

- Installing on the smart table

1.After removing the protective film from the double-sided adhesive tape, preserve the
tape so that it doesn't get dirty.
If touching the tape with a hand or foreign materials get on it, its adhesive strength

can be significantly deteriorated.

2.The adhesive tape will have full adhesive strength after the 24 hours from its placement.
Please do not use the products right after its placement.

- Cautions when attaching the double-sided tape.

Gear S3 frontier/Gear S3 classic

Normal Security Set

INSTALLATION MANUAL

G022_EN1610_R02

Please, read carefully the installation manual before installing it, and install it

according to the manual. Please, keep the manual for a future reference.

▶Before installing, Please check up the parts.

Maintenance kit

m1

■ Maintenance kit

Use if the product needs to be reinstalled.

m2

▶Installation Guide - Gear S3 frontier/classic Normal Security Set

2-A 2-B

■

Assembling flow

c

d e

f

g

a

a

a

a

a

b

Hole on the
smart table

Loosen the screw (silver) in the direction where the strap buckle side using the
screw driver included in the package.

※Make sure that the screw in the direction where the buckle side be loose.
※Keep the screw (silver) separated from Gear S3 carefully.

3

Assemble the Security sensor( ) along Gear S3 while paying attention to the assembling
direction. After assembling the Security sensor correctly, fix the Gear S3 and the Security
sensor firmly using the black screw( ) for fixing the Security sensor included in the package.

※Before assembling the product, make sure to check the screw color(black).

4

g

c

Hole on the
normal table

a

a

Remove the protective film from all double-sided tapes on the bottom surface of
the cradle( ).

1

b

b

Remove the

protective film

Refer to

Caution A.

B

- Installing on a normal table

CAUTION A.

.BHOFUJD-PDBUJPO

The first hole of

Gear S3 strap

Built-in Wireless

Charging Pad



Buckle

Gear S3

Screw
(Silver)

g

c

Check the LED lighting
on the Security sensor



c

Cradle

head

Cable

direction

Cable

direction

Protective

film

Remove

a

e

f

Cutting

a

Control box

Control box

▶Safety warning

▶How to separate the Security sensor

▶Information

※ The specifications and design of the product may be modified without prior

notice for the improvement of product performance.

Do not expose the product to fire or other electric heaters!

- There is a danger of fire or damage to the product.
Do not disassemble, repair, or remodel the product!

- There is a danger of injury.

- Please call the service center when repair is necessary.
Do not forcefully bend or pull the wire!

- There is a danger of damage to the product or injury to the user.
When the wire is disconnected or breaks away, do not touch the wire with

bare hands,

but always wear protective hand gloves!

- The disconnected part of the wire is sharp, thus, may cause injury.
Do not use the wire for purposes other than as a s ecurity alarm device , and do not allow
access to children!

- Winding the wire around your neck or body may result in death or serious injury.
Do not touch the wire when there is lightning and thunder!

- There is a danger of electric shock.

Warning: To prevent the injury of the user or other people and property damage,
the following instructions must be followed.

*In case of user’s fault during the warranty period it is not free of charge.

Warranty Period Item

One-year

Manufacturer

KUMOH Electronics Co.,Ltd

Address

35, Gilju-ro 444beon-gil, Wonmi-gu,

Bucheon-si, Gyeonggi-do (Seoul 14556 Korea)

[e-mail]

82-32-662-9312

82-32-662-2000

■ Limited warranty

■ Manufacturer Information

Tel

Fax

E-mail

Gear S3 frontier/classic

Normal Security Set

Turn off the Control box, separate the security cable connector( ), and loosen
the black screw( ) assembled to the Security sensor.

※If you separate the connector( ) without turning off the Control box, an alarm
will occur.

1

Separate the Security sensor( ) and assemble the screw(silver) for Gear S3.

※Make sure to use the screw(silver) separated from Gear S3 before installing the
Security sensor. If the screw(black) for installing the Security sensor is used,
it will not be assembled normally.

2

※ Before separating the Security sensor, make sure to turn off the Control box.

6

When mounting Gear S3 on the cradle head, check if the cable of the Security sensor( )
is installed correctly to direction of the rear side of the cradle as shown in the figure below.

※If the Security sensor is installed in the wrong direction, install it again by checking
the assembling direction in of the installation guide.

Install the buckle in the first hole of Gear S3 strap as below figure, and put the
device on the center of cradle head.

※Make sure that the buckle should be installed in the first hole of strap.

※The wireless charger and the magnet are built in cradle head.

5

g

c

a

a

a

The coil for wireless charging function and magnetic to places the Gear S3 in right charging point are built in head of security cradle.
When put the Gear S3 onto cradle, the magnetic power guides the device to center of cradle. If it is set apart from center, the charging will not Working.

3

Auto adjustment head by magnet

8

Assemble the security cable( ) temporarily using the cable tie( ) and the cable
tie mount( ). Remove the protective film from the double-sided table on the
bottom surface of the cable tie mount, attach the cable tie mount( ) firmly on
the proper position on the table, pull and tighten up the table tie( ) completely
and cut off any excess part.

After finishing the installation, connect the security cable connector( ) to the
Control box and turn on the power. If the power supply is connected normally,
LED on the Security sensor will turn on.

7

a

e

e

f

f

a

a

c

Press and hold evenly

for 30 seconds or more!

Magnetic power

set the Gear S3

to locate the

charging point.