GOLD SCAN II
User’s Manual
3D Detector
KTS-Electronic GmbH & Co. KG
Germany
KTS-Electronic GmbH & Co. KG – GOLD SCAN II
Table of contents
1. General guidelines.............................................................................................. 4
1.1 Introduction ................................................................................................. 4
1.2 Scope of delivery ........................................................................................ 5
2. Electronic Unit .................................................................................................... 6
2.1 Back side ..................................................................................................... 7
3. Search process ................................................................................................... 7
3.1 Search recommendations and hints for Reset operation ....................... 8
3.2 Exact location of metal objects ............................................................... 10
4. Search progress ............................................................................................... 11
4.1 Assembly ................................................................................................... 11
4.2 Usage and selection of searchcoils ........................................................ 11
4.3 25 cm coil .................................................................................................. 11
4.4 Cylindrical coil .......................................................................................... 12
4.5 1 x 1 m PVC search frame (depending on scope of delivery) ............... 12
4.6 Battery and chargers ................................................................................ 13
5. KTS-3D Software............................................................................................... 14
5.1 Software start-up ...................................................................................... 14
5.2 Main window .............................................................................................. 14
5.3 Toolbar ....................................................................................................... 14
File menu ................................................................................................... 14
Language ................................................................................................... 14
Info ............................................................................................................. 14
5.4 Adjustment range ..................................................................................... 15
5.5 Serial interface .......................................................................................... 15
5.6 Speed ......................................................................................................... 15
5.7 Position ...................................................................................................... 15
5.8 Start / Stop ................................................................................................. 15
5.9 Audio output .............................................................................................. 16
5.10 Scaling ....................................................................................................... 16
5.11 Presentation ................................................................ .............................. 16
5.12 Storage and transfer of measurement data ............................................ 16
6. Driver set-up (only after reinstalling) .............................................................. 17
6.1 Bluetooth pairing ...................................................................................... 17
6.2 Reading of COM-Ports .............................................................................. 18
KTS-Electronic GmbH & Co. KG – GOLD SCAN II
7. Error signals ..................................................................................................... 18
8. Technical data ................................................................................................... 19
9. License agreement ........................................................................................... 19
9.1 Utilisation clauses .................................................................................... 19
9.2 Disclaimer of liability ................................................................................ 19
10. Warranty ............................................................................................................ 20
10.1 Warranty expiration .................................................................................. 20
10.2 Care ............................................................................................................ 21
10.3 Legal note .................................................................................................. 21
11. Contact .............................................................................................................. 21
KTS-Electronic GmbH & Co. KG – GOLD SCAN II
4
1. General guidelines
1.1 Introduction
Dear customer,
we congratulate you on your purchase of GOLD SCAN II. Created by KTS-Electronic
GmbH & Co. KG, the GOLD SCAN II is the powerful successor of GOLD SCAN, which
is well-known in gold and treasure seeker circles.
The newly developed GOLD SCAN II metal detector impresses through its high
sensitivity towards gold and precious metals, easy handling and a larger display, which
shows all important information at a glance.
The following guide is important and useful in the search for gold and lost objects for
both gold and treasure hunters, archaeologists and industry as it can make the search
effortlessly.
To avoid possible operation errors we ask you to read all instructions carefully.
We wish you a successful search with your new GOLD SCAN II and are at your
disposal, should additional questions arise.
Your KTS-Electronic Team
KTS-Electronic GmbH & Co. KG – GOLD SCAN II
5
1.2 Scope of delivery
Hardware:
GOLD SCAN II electronic unit with Bluetooth® incl. installed li-Ion battery
Searchcoil 25 cm (9.84” – waterproof) with 2 part carbon telescopic pole
Cylindrical coil 5 x 20 cm (1.96 x 7.87” – waterproof) with 10 m (32.8 ft.) cable
1 x 1 m (3.28 x 3.28 ft) search frame, incl. backpack (depending on scope of
delivery)
Tablet Computer with KTS software and operation system incl. li-Ion battery
Powerful quick-charger (2800 mAh) with power inverter, car-charging cable and
additional 110V adapter
Solid hard-top case
Software:
KTS-3D software for GOLD SCAN II (pre-installed on PC)
USB stick with software for processing data on other computers
Service:
User’s manual English, German, Spanish or French
2 years manufacturer's warranty for the entire scope of delivery (including
hardware and software)
KTS-Electronic GmbH & Co. KG – GOLD SCAN II
6
2. Electronic Unit
Compared to its predecessor the advantage of GOLD SCAN II consist primarily in the
fact that the sensitivity towards gold and precious metals was substantially increased
and the setting was simplified. Instead of several control knobs the new device has
only one ON- / OFF-button and a display that delivers all informations at a glance.
This makes the search considerably easier.
The electronic unit is installed in a stable box and carried in a leather bag.
Power: The new GOLD SCAN II is equipped with only one ON-/OFF-button.
Reset: Automatic zero balance at the touch of a button. By activating the Reset-
button the device will be aligned to the actual soil condition.
Freq.: Frequency adjustment.
Audio: Volume control
Bluetooth (BT): green operating LED for Bluetooth connection with computer.
Display: ID: Presentation of metal type and display of conductivity
BAT: Battery control (graphically and in percent).
KTS-Electronic GmbH & Co. KG – GOLD SCAN II
7
2.1 Back side
1. Charger (connection to the charging device / separate plug): For charging the
battery the plug of the charging device has to be plugged into the provided
connector socket. The maximum charging time is 90 minutes (to avoid a defect
on the charger or the built-in battery, please do not exceed this time). The
connector of the charger should be removed after each charge.
2. Headphone socket: Any commercial headphones with 6.3 mm jack can be
plugged in. During use the loudspeaker is turned off. Matching, light weight
headphones are provided.
3. Socket for coils: The connecting socket for coils is located on the left side. The
connector plug of the searchcoil has to be plugged into the socket. Before
removing the plug the locking knob must be pressed, only then an extraction is
possible. The connector is compatible with all GOLD SCAN II searchcoils.
3. Search process
Please note the following:
Stay away from conducting overhead lines
Do not use cell phone during operation
Do not process any measurement during thunderstorms
Protect device from wetness
Accurate operation is only guaranteed with a fully charged battery
For operation or charging only use the components enclosed or released by KTS
GmbH & Co. KG.
GOLD SCAN II is a PC-connected metal detector, which is provided with the KTS-3D
software. First you should use this device like a common metal detector without 3D
software, i.e. search and identify your findings on your display (metal type), then
mark the place of discovery. Later you can scan the spot more precisely by using
your laptop with the KTS-3D software. The handling of laptops and the respective
settings will be explained in chapter 5 (page 15).
KTS-Electronic GmbH & Co. KG – GOLD SCAN II
8
The GOLD SCAN II is ready for use within a very short time:
1. Activate the metal detector with the ON-/OFF-button. The respective searchcoil
should be cable-connected to the electronic unit in advance.
2. Hold the searchcoil to the ground and press the Reset-button for a brief
moment. You herewith attain a zero balance, which is necessary for a troublefree search.
Please make sure, that there are no metal objects near the searchcoil during
zero balance. This could cause a wrong adjustment of the metal detector and
produce unwanted indicator effects (as the case may be repeat the RESET-
procedure on another, metal-free spot).
3. In the beginning please set the frequency to the lowest level (turn the Freq.-
modulator clockwise). The volume should be set hearable with the help of the
Audio control. Generally we recommend to start with the lowest frequency
adjustment to acquaint yourself with the handling of the device. With advancing
experience it is expedient, to increase the frequency gradually, what will have a
positive effect on the search performance.
3.1 Search recommendations and hints for Reset operation
During the search process be sure that you do not carry items of metal with you. This
could cause a wrong adjustment when pressing the Reset key and can produce false
indicator effects. In addition, this can lead to a false metal discrimination. While
searching be ensured, that the sound remains constant, otherwise a wrong
adjustment caused by magnetic fields may occur. In this case, the searchcoil is held
above the ground and the display has to be observed after renewed actuation of the
Reset-button and the adjustment of the frequency. The GOLD SCAN II has a
constant metal discrimination. Thereby the inserted microprocessor computes the
conductivity of the metal objects and indicates them on the digital display
Note: For a successful search the function of the Reset-button is of utmost
importance.
KTS-Electronic GmbH & Co. KG – GOLD SCAN II
9
After each of the following changes please press the Reset-button:
1. After every engaging of the metal detector.
2. After each change of searchcoils.
3. During the search, if sound becomes instable due to bad ground conditions or
geomagnetism.
To create the search more target-oriented and therefore more successful – especially
before excavation – please draw your attention to the following:
1. Change of sound (frequency)
2. Intensity of sound
3. Continuity of sound
4. Extent of value (digital display)
The change of sound is the first sign for the detection of a metal object. Before
excavation, however, further details should be taken into account and the own search
experience should be used for help:
The more intense the sound, the larger the metal object and the nearer the position
to the surface. While the high search tone is audible, it is required to move the
searchcoil in the close surrounding to determine the shape of the metal object.
ID (metal discrimination):
Compared to the predecessor model, in which only a single measurement was
conducted, GOLD SCAN II enables the discrimination by a special measuring
method. Now 5 measurements are carried out, which will calculate the average
value. The average value calculation leads to a more precise metal type
discrimination. The extent of the metal type range makes it possible to distinguish
different size metal objects with the appropriate values from one another. The
average value is shown in sector gold with 100-1000, in the range of copper with
1000-2500 and in the field of light metals, e.g. aluminum, as of 2500.
Unlike to other metal detectors a constant metal discrimination takes place at the
GOLD SCAN II. Conductivity value and metal type (e.g. “Gold”) are indicated on the
display.
Note: The new GOLD SCAN II shows a very sensitive reaction towards small gold objects
(e.g. nuggets). Through the increase of frequency the depth performance also rises. Due
to difficult soil conditions it can occur, that interferences will escalate. With a renewed
Reset and a reduction of frequency this can be lowered.
KTS-Electronic GmbH & Co. KG – GOLD SCAN II
10
As long as the searchcoil is exactly located over the metal object the displayed
conductibility value is decisive.
To identify a metal object a weak tone is inadequate. To compute the conductibility of
a metal object a signal with high intensity is necessary.
Please bear in mind that – depending on soil conditions as well as size and shape of
the located objects – the measured values can diversify. The indicated values are
guide values, which can be complemented with your own search routine
See also the explanation of false signals on page 18.
Note: To avoid incorrect conductivity values it is absolutely necessary to repeat the
adjustment of the soil balance. When pressing the Reset-button make sure, that there are no
metal parts in the soil..
3.2 Exact location of metal objects
GOLD SCAN II works with the pulse induction searching system and is able to detect
without setting the searchcoil in motion. While approaching an object with the
searchcoil you will notice an increase of sound frequency. As soon as the searchcoil
is exactly positioned over the object, the highest tone is reached and the displayed
conductivity value corresponds to the probable kind of metal.
With this method not only the exact place of discovery is located, the shape of the
item can also be identified through the sound continuity. For example, a long-lasting
high tone stands in longitudinal direction for a slim object, e.g. a pipe. A high tone in
any direction indicates a ringlike object.
KTS-Electronic GmbH & Co. KG – GOLD SCAN II
11
4. Search progress
4.1 Assembly
1. Install the carbon telescope bar by screwing the carbon tube (adjustable in length)
to the armrest.
2. Insert the plug into the provided connector of the unit’s backside. The electronic
unit is kept in a carrying leather bag through which lower opening the plug is to be
inserted (see also page 7, item 2.1).
4.2 Usage and selection of searchcoils
In addition to your GOLD SCAN II we deliver several searchcoils, each suitable for
certain applications.
Note: A slewing of the searchcoil is no longer necessary. Just hold the searchcoil flat and
parallel to the ground and determine your search speed.
4.3 25 cm coil
The 25 cm searchcoil is particularly
suitable for the search after small metal
objects.
Operation:
1. It is advisable to hold the searchcoil parallel to the ground level.
2. After activation and regulation of volume and frequency press the Reset-button for soil
balance.
3. For the ground balance regulation hold coil about 5 cm above the ground (on a metalfree spot, e.g. hold the coil in the air) and press the Reset-button for approx. 3 seconds.
With the ground balance regulation the influence of minerals in the soil is neutralized and
less error signals are produced.
4. Repeat the ground balance regulation at various spots, so that the regulation is always
carried out correctly. It is recommendable to repeat this process, particularly by changes
in soil layers as caused by excavations.
KTS-Electronic GmbH & Co. KG – GOLD SCAN II
12
4.4 Cylindrical coil
By its dimensions of 5 x 20 cm the cylindrical coil
especially is applicable in narrow spaces (e.g.
crevices) or in inaccessible spots (wells, shafts,
other excavations). The coil is supplied with a cable
of 10m in length.
4.5 1 x 1 m PVC search frame (depending on scope of delivery)
The provided 4 m cable coil is fastened to the 1 x 1
m PVC frame. The search frame is primarily used
for the deep sounding after medium-sized and
large metal objects. The frame is indispensable for
the search in large areas. Furthermore small scrap
iron parts are automatically filtered.
Note: Metal detectors create magnetic fields in the searchcoil. Under certain circumstances
they can be affected in their functionality when operated in the vicinity of industrial plants or
electronic devices.
Assembly:
As a first step connect the PVC pipes (8-fold demountable) to each other, then fix the
cable with a tape to the pipes.
KTS-Electronic GmbH & Co. KG – GOLD SCAN II
13
Application:
The search frame is build of lightweight plastic pipes and a 4m cable, which has to be
attached to the pipes. The frame can be carried from 1 or 2 persons and is most
adequate for the search after large objects, which are expected in a large-scale area.
It is recommended, to keep the distance to the soil surface as low as possible. The
advantage of the search frame is, that it does not indicate small disturbing metal
parts.
To avoid unwanted influences caused by earth magnetism the Reset button should
be activated, if sound is unstable.
Note: Strongly magnetized soils affect large searchcoils (search frame) more than small
searchcoils. For this reason be certain, that when you are searching with the large coil it is
kept approx. 15-50 cm (depending upon landscape) parallel to the soil and avoid jerky
movements.
4.6 Battery and chargers
The strong pulse power is reached by the builtin 2800 mAh-li-Ion battery, which is charged
within 90 minutes. Please note, that the supply
cable for the battery charger has to be removed
after each charging procedure.
The actual working time amounts to (depending
upon coil size and usage of headphones)
approx. 4-8 hours.
In addition, we deliver an inverter which
enables the charging in the car.
Note: The maximum charging time is 90 minutes. To avoid a defect on the charger or the
built-in battery, this charging time should not be exceeded (could lead to a loss of warranty
of damaged charger).
KTS-Electronic GmbH & Co. KG – GOLD SCAN II
14
5. KTS-3D Software
The program serves the visualisation of measurement data in colored, 3-dimensional
representation, in particular the display of magnetic field data.
The 3D software is preinstalled on the provided tablet computer. For operating of the
tablet computer please read device’s manual.
5.1 Software start-up
Open the software through double-click of
icon KTS-Online (preinstalled on desktop)
5.2 Main window
After start of program the main window appears with the menu bar, the adjustment
segment (left) and the display area (right).
Illustration shows a demo record.
5.3 Toolbar
File menu
The file menu is found in the menu bar with entries for storage and reading of measurement
files. In addition, the program can be closed here.
Language
The program allows the switch to several languages (English, German, French and Spanish).
Info
A display delivers information of the present software version.
KTS-Electronic GmbH & Co. KG – GOLD SCAN II
15
5.4 Adjustment range
All settings are stored and available with the next program start.
5.5 Serial interface
Here you can choose the COM-port for the connection to the measurement
hardware. In this list only the present COM-port will be shown. The number of the
COM-ports can be read out in the Windows Device Manager (s. page 18, 6.2).
5.6 Speed
You may select three levels of measuring speed. The movement on the tracks must
comply with your speed. A switch is also possible with the function keys [F2], [F3]
and [F4].
5.7 Position
The 3D display can be rotated and tilted. The center button [0] resets to the origin
presentation.
5.8 Start / Stop
By pressing the Start button the search begins. The first results will be displayed 2dimensional until the measurements are completed. For the next measuring you must
press the start button again. With the button [Stop] you can interrupt the
measurement at any time.
The measuring process starts with a countdown. The figures are accompanied by
short audio signals. After the Start display the coil must be moved from left to right.
For this purpose follow the appearing colored lines. After every end of a line the coil
must be slightly moved forward. At the end of the track the audio signal is repeated.
The recording automatically stops after the last track.
KTS-Electronic GmbH & Co. KG – GOLD SCAN II
16
Note: To ensure a correct measurement, it is absolutely necessary to press the
Reset-button before every search process and light up of the Reset LED.
5.9 Audio output
The sound can be turned on or off. The volume is adjustable in 10% steps from 0 to
100%. Of course, the volume control depends on the individual volume of your PC.
5.10 Scaling
With the support of scaling the presentation in the color spectrum will be adapted
optimally. The lower limit is shown in blue color, the maximum limit appears in red.
The use of scaling is especially recommended for less distinctive color changes.
5.11 Presentation
The measurement data is displayed color-coded and 3-dimensional. Low values
correspond to the color blue, green or yellow are assigned to medium measured
values. High readings are shown in red.
In the data menu you have the option to store measured data resp. display the
measurements again. By pressing the right mouse button the 3-D presentation can
be rotated in all directions. The [0] button leads you back to the origin presentation.
5.12 Storage and transfer of measurement data
For a subsequent analysis the measurement data is stored. We recommend the
further data processing in the undisturbed atmosphere of your home, where perhaps
a larger display is available.
If you want to evaluate the measured data on a larger display later on, transfer it to
the provided USB stick, on which the complete software is pre-installed.
KTS-Electronic GmbH & Co. KG – GOLD SCAN II
17
6. Driver set-up (only after reinstalling)
Note: If you want to use another laptop to connect the main unit or had to reinstall
Windows, first of all copy the folder from the supplied USB-stick to your computer
(see 6.1).
System requirements
You can connect your GOLD SCAN II to any PC or Laptop equipped with Bluetooth
and Windows software and the following conditions: The software works with
Windows 98, 2000, NT, XP or Vista or WIN 7 or 8. As minimum requirements for a
smooth operation the PC should be equipped with the following:
Processor with a pulse frequency of 1000 MHz or more
Hard drive with about 10 .. 20 MB free space
Graphic card with a minimum resolution of 800 x 600 points
Bluetooth ability to connect the external measuring hardware
Please note, that the minimum resolution is 800x600, otherwise important
functions can not presented.
6.1 Bluetooth pairing
The Bluetooth symbol will appear
in the menu bar. With right mouse
button on the above symbol the add
a device–window shows all available
Bluetooth functions (it is necessary
that GOLD SCAN II is active and the
green LED flashes).
Select Ezurio Blu 2I and click “Next”.
In the next window pick “Enter the
device’s pairing code”, insert the
password “1234” and go to “Next”
(GOLD SCAN II automatically will
instal the suitable drivers). Finally
click the Close-button to conclude the
procedure
KTS-Electronic GmbH & Co. KG – GOLD SCAN II
18
6.2 Reading of COM-Ports
Click on the Bluetooth icon at the
Windows taskbar on the right side.
Open the Bluetooth settings and
there the COM-Ports. Write down the
Outgoing-No. (COM .... - usually
between 3 and 6) and click OK.
After that open KTS-Online Software,
and select the memorized
COMPORT in field “Serial Port”. By
restarting the software the device
automatically will be connected to the
computer. The LED lights up
permanently and GOLD SCAN II is
operational.
For further application please note, that Bluetooth and GOLD SCAN II are active
(above proceedings must not be repeated).
7. Error signals
During development of GOLD SCAN II particular emphasis was laid on stability and
the avoidance of malfunctions. Despite the high number of filters and modulators it
may occur, that certain soil conditions cause disturbances, which can influence your
measured values.
Apart from a wrong soil balance adjustment incorrect signals can emerge by the
following effects:
1. Ferric oxide: Through magnetic ferric oxide soils the conductance value of the located
metal can comprehend falsified data.
2. Anomaly effects can lead to the fact that large iron metals are indicated as precious
metal.
3. Small parts of bronce partially may be indicated as iron. The accuracy of the measured
values is therefore only ensured starting from an object of 5 x 5 cm in dimension.
4. The measured values can be falsified, because other metal parts are located near the
found metal object.
5. Strongly magnetic interference fields within residential areas and in the vicinity of ground
cables can influence the measured values, especially when working with the large
searchcoil.
6. Disturbances often occur in the peripherals of radio stations.
7. Strongly magnetic fields, particularly in the neighbourhood of high voltage masts, can
cause disfunctions.
KTS-Electronic GmbH & Co. KG – GOLD SCAN II
19
8. Technical data
Electronic unit
Dimensions ca.: 18 x 22 x 7 cm
Weight: 1450 g (incl. bag with shoulder strap)
Power supply: integrated li-Ion battery 12 Volt (fully charged 14-16 V) / 2800 mAh
Operating time: ca. 4-8h
Charging time: maximal 90 minutes
car-recharger: external car-recharger (connectable to cigarette lighter)
1 x 1 m coil (depending on scope of delivery)
Dimensions: 8-fold demountable, incl. transport bag, approx. 60 cm length
Weight: total weight incl. transport bag approx. 1.2 kg
9. License agreement
The program KTS-3D as well as the entire accompanying electronic or printed
documentation are subject to the copyright of KTS-Electronic GmbH & Co. KG. If
parts of the present license regulations should show alterations or expansions in
comparison to license regulations for former program versions, the current license
regulations are valid with the beginning of the effective date.
The present license regulations come into effect on May 1st, 2007.
Through the utilisation of the software, the user agrees to the present license
regulations. For each incidence of violation of the terms of license the right of
utilisation automatically becomes void.
9.1 Utilisation clauses
After full payment of the invoice amount the customer is allowed to a not-exclusive
right of usage of the program listed in the bill. This right is restricted to the owner of
the original software. Consequently, the software can be used only on one single
computer system at the same time.
All present and future copyrights and/or industrial protection rights of the provided
programs and of all programs diverted from them, program modules or in this context
created documents remain at KTS-Electronic GmbH & Co. KG.
9.2 Disclaimer of liability
The present program was tested with great care and accuracy, nevertheless
mistakes cannot be ruled out. No guarantee is adopted for the usability of the
program to a certain purpose. Especially, no liability is adopted for consequential
damages as well as profit and asset losses, that could result from the application of
the program as well as the affiliated documentation.
KTS-Electronic GmbH & Co. KG – GOLD SCAN II
20
Prices may change without notice. The same applies to changes any sort in software
or documentation.
10. Warranty
We grant repair works free of charge due to factory errors originated by mistakes and
defects 24 months from date of purchase.
According to the following conditions (see below) we remedy deficiencies free of
charge, if they are evidently based on manufacturing errors or defects and are
reported to us immediately after detection of damage within 24 months after delivery
to the first buyer.
Divergencies from the required quality of the goods, which are insignificant for the
suitability of value and use (failures caused by chemical or electrochemical
influences, damages resulting from wetness as well as from non-standard handling in
general) are irrelevant and excluded from the warranty.
Defective parts will be repaired gratuitous or replaced by unobjectionable parts of our
choice. KTS reserves the right to exchange the device for a product of equivalent
value in case the returned product cannot be repaired in an appropriate budget time
frame. On-site repairs cannot be demanded. Replaced, resp. exchanged parts will
merge into our property.
The guarantee claim expires in cases of improper handling, gross carelessness or if
repairs, modifications, additionally installed parts or extentions are carried out from
persons which are not authorized on our part to do so.
Guarantee claims will neither effect an extention of the term nor they will implement a
new guarantee period.
Further claims are excluded, in particular such through extraneous causes resulting
product damages, provided there is no obligatory legal liability. We therefore are not
liable for any accidential, indirect or other subsequent damages of any kind, which
lead to limited use, data loss, profit setbacks or operating failures.
We therefore are not liable for any accidential, indirect or other subsequent damages
of any kind, which lead to limited use, data loss, profit setbacks or operating failures.
10.1 Warranty expiration
KTS-Electronic GmbH & Co. KG can agree upon a service after the term of
guarantee is expired. In this case repairing and shipment will be charged.
KTS-Electronic GmbH & Co. KG – GOLD SCAN II
21
10.2 Care
Your GOLD SCAN II requires little maintenance, yet there are some items, which you
should consider, in order to receive its optimal readiness for operation. Avoid extreme
temperatures, since it can be possible that electronic construction units are damaged
thereby. Protect the electronic housing with a plastic bag in case you should get
caught by rain, fog or dust. Always keep your equipment clean and dry and wipe off
sand and dirt.
10.3 Legal note
Before you start searching please note that the monument protection as well as other
legal standards are relevant. KTS-Electronic GmbH & Co. KG. assumes no
responsibility for possible legal violations.
In case of doubts we recommend a comprehensive consultation with an attorney or
national monument offices.
11. Contact
KTS-Electronic GmbH & Co. KG
Kurhessen Strasse 1
64546 Moerfelden-Walldorf
Germany
Tel: +49-(0)6105 9111-50
Fax: +49-(0)6105 9111-55
www.kts-electronic.com
eMail: mail@kts-electronic.com
Office hours:
Mondays – Thursdays: 9:00 am to 4:30 pm
Fridays: 9:00 am to 4:00 pm
Copyright: KTS-Electronic GmbH & Co. KG, Moerfelden-Walldorf/Germany, 2015
The right to reproduction or the disposal of graphics and/or texts of this publication is
without autor’s explicit consent not allowed.
Loading...