Page 1
KGS-800L Ver.D
Gigabit Ethernet Switch
UUsseerr’’ss GGuuiidde
e
DOC.080114
Page 2
1. Introduction
The 10BASE-T/100BASE-TX/1000BASE-T Switches which are
high-performance Gigabit Ethernet Switches designed for the network core. It
provides 8 10BASE-T/100BASE-TX/1000BASE-T ports that can significantly
improve the performance of your network’s backbone, and deliver the
throughput needed to support a broad range of advanced network applications.
With Switches high performance band-width, it provides the quickest solution
to meeting the growing demands on your network’s limited resources.
2. Features
z Complies with the IEEE 802.3 10Base-T Ethernet,
IEEE 802.3u 100Base-TX Fast Ethernet and
IEEE 802.3ab 1000Base-T Gigabit Ethernet standards.
z Compact size.
z 8-port 10/100/1000 Mbps auto-MDI/MDI-X.
z Secure store and forward switching scheme.
z Auto correction of reverse twisted pair polarity.
z All ports support half/full duplex, Nway auto negotiation.
z All ports support 802.3x flow control for protection against data loss.
Page 3
3.Package Contents
z User Manual.
z Power Adapter.
z 10/100/1000Mbps Gigabit Ethernet Switch.
4. Hardware Introduction
4.1 Front Panel
POWER LED
This LED light is on when power is present.
8 Port LED
Indicates the status of each of the 8 ports.
Speed 100 Mbps LED
A green LED indicates the speed is 100 Mbps.
Speed 1000 Mbps LED
An orange LED indicates the speed is 1000 Mbps.
Link/Activity LED
There is a link when the LED light is lit, there is an activity when the LED
blinks
Page 4
4.2 Rear Panel
DC-input
connect power adapter
8 Port Gigabit Switch
connect computers, hub’s, switches or other devices.
Page 5
Specifications
IEEE 802.3 10Base-T
Standards
Data Transfer Rate
Interface
Diagnostic LED
Power Input
Dimension
IEEE 802.3u 100Base-TX
IEEE 802.3ab 1000Base-T
- Ethernet : 10Mbps (half-duplex)
20Mbps (full-duplex)
- Fast Ethernet : 100Mbps (half-duplex)
200Mbps (full-duplex)
- Gigabit Ethernet : 1000Mbps (half-duplex)
2000Mbps (full-duplex)
8 x 10/100/1000Mbps Auto-MDI/MDI-X Ports
Power, Link / ACT, 100Mbps / 1000Mbps
DC 5V / 2A min. or DC 7.5 / 1.2A min.
109 x 155 x 33mm
Operating Temperature
Operating Humidity
EMI Certification
0°C ~ 40° C (32°F ~ 104° F)
10% ~90% RH, Non-condensing
FCC Class B / CE Class B
Page 6
5. FCC Warning
This equipment has been tested and found to comply with the regula-tions
for a Class B digital device, pursuant to Part 15 of the FCC Rules. These
limits are designed to provide reasonable protection against harmful
interference when the equipment is operated in a commercial environment.
This equipment generates, uses, and can radiate radio frequency energy
and, if not installed and used in accordance with this user’s guide, may
cause harmful interference to radio communications. Operation of this
equipment in a residential area is likely to cause harmful interference, in
which case the user will be required to correct the interference at his own
expense.
z Reorient the receiving antenna.
z Increase the separation between the equipment and receiver.
z Connect the equipment into an outlet on a circuit in a different room
that to which the receiver is connected.
z Consult the dealer or an experienced radio/TV technician for help.
6. CE Mark Warning
This is a Class B product. In a domestic environment, this product may
cause radio interference, in which case the user may be required to take
adequate measures.
Loading...