KTI Networks KC-220FF-TSA, KC-220FF-TS3, KC-220FF-TS5, KC-220FF-CSA, KC-220FF-CS3 Installation Manual
...Page 1
Specifications
Complies with IEEE 802.3u 100BASE -FX std.
Operates with connected devices running on full duplex
or half duplex mode
Environment: Temperature 0 - 40oC
Humidity 10-90% non condensing
Dimensions: 101mm x 96mm x 25mm
Power: +12V / 800mA minimum
DC plug type:
Connectors & Cables
The converter provides one multimode (MM) fiber port
and one single mode (SM) fiber port as shown below:
The multimode fiber port is used for a duplex multimode
fiber cable connection and single mode fiber port is used
for a duplex single mode fiber cable connection.
Both ports are compliant to IEEE 802.3u 100BASE-FX
standard and can convert multimode optic signal to single
mode optic signal up to bandwidth 200Mbps transparently with a minimal delay time.
The wavelength used is 1300nm for both ports. The
recommended MM (Multimode fiber) cable is 62.5/125mm
and SM (Single Mode fiber) cable is 9/125mm.
General Description
The KC-220FF Fast Ethernet media converter series are designed to convert a 100BASE-FX multimode fiber signal to
single mode fiber signal. It is used to extend the connection
distance between two Fast Ethernet fiber optic devices via
single mode fiber cable transparently with no performance
degradation. The converter series provide different types of
fiber connectors such as ST, SC, and MT-RJ for MM (multimode) or SM (single mode) fiber cables.
The outline of the converter is:
Installation Guide
100BASE-FX Multimode-Single mode
Media Converter
KC-220FF SERIES
DOC. 010430-KC220FF-K Rev.1.0
P/N: 750-0155-001
The series provides different types of fiber connectors for
different applications. The connectors include ST, SC, and
MT-RJ. The following figure illustrates the available
combinations:
The following table lists the fiber connectors, fiber cables
and the maximum length supported by each converter
model:
Model MM Port* SM Port SM Cable Length*
KC-220FF-TSA ST SC 15Km
KC-220FF-TS3 ST SC 30Km
KC-220FF-TS5 ST SC 50Km
KC-220FF-CSA SC SC 15Km
KC-220FF-CS3 SC SC 30Km
KC-220FF-CS5 SC SC 50Km
KC-220FF-CJ SC MT-RJ 15Km
KC-220FF-JJ MT-RJ MT-RJ 15Km
KC-220FF-JSA MT-RJ SC 15Km
* MM Port : the maximum MM cable length is 2K meters.
* SM Cable length : the maximum length in point-to-point full
duplex operation
Page 2
The information contained in this document is subject to change
without prior notice.
Copyright+ KTI. All Rights Reserved.
TRADEMARKS
Ethernet is a registered trademark of Xerox Corp.
WARNING:
This equipment has been tested and found to comply with the
limits for a Class A digital device, pursuant to Part 15 of the FCC
Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is
operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and if not
installed and used in accordance with the instruction manual
may cause harmful interference in which case the user will be
required to correct the interference at his own expense.
NOTICE:
(1) The changes or modifications not expressively approved by
the party responsible for compliance could void the user's
authority to operate the equipment.
(2) Shielded interface cables and AC power cord, if any, must
be used in order to comply with the emission limits.
CISPR A COMPLIANCE:
This device complies with EMC directive of the European
Community and meets or exceeds the following technical
standard.
EN 55022 - Limits and Methods of Measurement of Radio
Interference Characteristics of Information Technology Equipment. This device complies with CISPR Class A.
WARNING: This is a Class A product. In a domestic environment
this product may cause radio interference in which case the
user may be required to take adequate measures.
CE NOTICE
Marking by the symbol indicates compliance of this
equipment to the EMC directive of the European Community. Such
marking is indicative that this equipment meets or exceeds the
following technical standards:
EN 55022: Limits and Methods of Measurement of Radio
Interference characteristics of Information Technology Equipment.
EN 50082/1:Generic Immunity Standard -Part 1: Domestic
Commercial and Light Industry.
EN 60555-2: Disturbances in supply systems caused by
household appliances and similar electrical equipment - Part 2:
Harmonics.
Installation
1. Install the media converter with the DC power adapter
provided. ( +12VDC, 800mA)
2. Connect the power adapter cable to the media converter before connecting the adapter to the AC outlet.
Making Network Connections
The converters serve as a conversion path between two
Fast Ethernet Multimode fiber devices. To both devices,
the conversion is transparent.
Important rule: When a connection is established, make
sure the devices located at both ends of the path are
configured and operated using the same duplex mode and
the maximum distance must comply with IEEE 802.3u
specifications.
Interpreting LED Indicators
LED Status State Interpretation
POWER Power status On Converter is on.
Of f Converter is off.
MM MM port link On The MM fiber link is ok.
Off No link or the link is faulty.
SM SM port link On The SM fiber link is ok.
Off No link or the link is faulty.
Loading...