KTI Networks KC-10FM User Manual 2
Installation Guide
Ethernet Media Converter
Model: KC-10FM
Specifications
• Complies with IEEE 802.3 10BASE-T and 10BASE-FL std.
• Supports UTP cable up to 100 meters (328 feet)
• Supports fiber optic cable up to 2000 meters (6500 feet)
• Supports LED indications for the Power, UTP Link,
UTP Receiving, Fiber Link, and Fiber Receiving status
• Environment: T emperature 0 - 40oC
Humidity 10-90% non condensing
• Dimension: 74mm x 51mm x 20mm
• Power: +12V / 500mA minimum
Connectors & Cables
10BASE-T RJ-45 Connector
One RJ-45 switch is provided for selecting the type of RJ45 connector as follows:
Installation
1 . Install the media converter with the DC power adapter
provided. ( +12VDC, 500mA)
2 . Connect the power adapter cable to the media con-
verter before connecting the adapter to the AC outlet.
DOC. 980422-KC10FM-K
P/N: 750-0111-001
General Description
KC-10FM Ethernet media converter is designed to be a
connection interface between a 10BASE-T Ethernet UTP
cable and 10BASE-FL fiber cable. It features a RJ-45
connector and a pair of ST fiber optic connectors.
The converter complies with IEEE 802.3 10BASE-T and
10BASE-FL standard and supports a UTP cable up to 100
meters and a fiber optic cable up to 2000 meters with no
increasing on the hop count in the network.
RJ-45 Switch RJ-45 Type
X position MDI-X
II position MDI-I
RJ-45 Pin MDI-X type MDI-I type
1 Rx+ Tx+
2 RX- Tx 3 Tx+ Rx+
6 Tx- Rx-
It allows you to make all UTP connections using common
straight-through UTP.
10BASE-T UTP Cable
Cable type: Category 3, 4 or 5
Maximum cable distance: 100 meters (328 feet)
Fiber Optic Connectors
T wo ST connectors are provided for fiber optic cable
connection. One is labeled "Tx" for transmitting operation.
The other is labeled "Rx" for receiving operation.
3 . Do not connect more than two media converters in
series.
Making Network Connections
The following example illustrates a connection from a
10BASE-T port of one hub to a 10BASE-FL port of
another hub through a media converter.
The following example illustrates a connection from a
10BASE-T port of one hub to a 10BASE-T NIC on a
computer through a media converter.
Fiber Optic Cable
Cable type: 62.5/125 mm multimode fiber (recommended)
Maximum cable distance: 2000 meters (6500 feet)
Interpreting LED Indicators
LED Status State Interpretation
Powe r Power status On Converter is on.
Of f Converter is off.
Link Fiber link On The fiber link is ok.
Off No link or the link is faulty.
Rx Receiving status Blink Receiving is in operation.
Off No fiber receiving.
Link UTP link On The UTP link is ok.
Off No link or the link is faulty.
Rx Receiving status Blink Receiving is in operation.
Of f No fiber receiving.
The information contained in this document is subject to change
without prior notice.
Copyright Ó KTI. All Rights Reserved.
TRADEMARKS
Ethernet is a registered trademark of Xerox Corp.
WARNING:
This equipment has been tested and found to comply with the
limits for a Class A digital device, pursuant to Part 15 of the FCC
Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is
operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and if not
installed and used in accordance with the instruction manual
may cause harmful interference in which case the user will be
required to correct the interference at his own expense.
NOTICE:
(1 ) The changes or modifications not expressively approved by
the party responsible for compliance could void the user's
authority to operate the equipment.
(2 ) Shielded interface cables and AC power cord, if any, must
be used in order to comply with the emission limits.
CISPR A COMPLIANCE:
This device complies with EMC directive of the European
Community and meets or exceeds the following technical
standard.
EN 55022 - Limits and Methods of Measurement of Radio
Interference Characteristics of Information Technology Equipment. This device complies with CISPR Class A.
WARNING: This is a Class A product. In a domestic environment
this product may cause radio interference in which case the
user may be required to take adequate measures.
CE NOTICE
Marking by the symbol CE indicates compliance of this equipment
to the EMC directive of the European Community . Such marking is
indicative that this equipment meets or exceeds the following
technical standards:
EN 55022: Limits and Methods of Measurement of Radio
Interference characteristics of Information Technology Equipment.
EN 50082/1:Generic Immunity Standard -Part 1: Domestic
Commercial and Light Industry.
EN 60555-2: Disturbances in supply systems caused by
household appliances and similar electrical equipment - Part 2:
Harmonics.
Loading...