KT&C KPC-Xi210HD User Manual
M111-Xi210HD-001
MegaPixel Network Camera
3. Product Description
Description and function
4. Install the hardware
KNC-Xi210HD is designed to be installed using standing bracket on the wall or ceiling.
KNC-Xi210HD
Installation Guide
Table of Contents
1.INTRODUCTION
2.PACKAGE CONTENTS
3.PRODUCT DESCRIPTION
4.INSTALL THE HARDWARE
5.ASSIGN AN IP ADDRESS
6.TERMINAL BLOCK CONNECTORS
1. Introduction
KNC-Xi210HD Installation Guide
This installation guide provides instructions for installing the Network Camera on
your network. For all other aspects of using the product, please see the User’s
Manual, available on the CD included in this package, or from http://www.ktnc.co.kr
Installation steps
1. Check the package contents against the list below.
2. Product description
3. Install the hardware
4. Set an IP address
5. Set the admin and user ID and password, See User’s Manual.
instructions in further usage.
Important!
This product must be used in compliance with local laws and regulations.
2. Package Contents
④
③
②
⑩
⑪
⑥
⑤
①
⑦
⑨
⑧
⑮
⑬
⑭
1. Micro SD/SDHC Memory Slot – Insert Micro SD o Micro SDHC memory card for recording videos
and saving images.
2. Line / MIC In – Connect 3.5mm jack from line level audio source or MIC.
3. Line Out – Connect 3.5mm jack from speaker.
4. Reset Switch/NTSC or PAL select – Push and hold the reset button for more than 10 second to
reset the Network Camera. Push this switch to use analog
video of NTSC or PAL format on installing.
5. Digital Input – Connect signal from external sensor.
CAUTION
CAUTION
6. Digital Output – Connect signal to external alarm. (Max. current - DC 12V, 40mA)
7. Network LED – Network LED indicates network connection status.
8. Network Connector – The Network Camera connects to the network via a standard network cable,
and automatically detects the speed of the local network segment (10BaseT/
100BaseTX Ethernet).PoE Supported.
9. Status LED – Status LED indicates the Network Camera operation status.
10. Power Input(DC12V/AC24V) – Connect DC 12V or AC 24V power.
11. Service Video Connector – For checking the view of the camera on a portable monitor when the
camera is being installed.
CAUTION
12. Auto Iris Jack – Connect DC Iris cable.
13. Back Focus Adjustment Level – Use to adjust focus.
14. Focus Fixing Screw – Use to x back focus adjustment level.
15. Tripod Mounting Hole – Use to connect standing bracket.
: This feature will reset all settings to the original factory default settings.
: This button has two functions(factory default settings or selecting analog video).
The analog video can be viewed only in 1280x1024 resolution.
:
⑫
Lens connection
Lens are sold separately. Lenses such as an auto iris lens, CS-Mount and C-Mount lens can be used.
Note:
• It is recommended that megapixel lens are used to optimize performance.
• Please keep the lens clean.
• Any foreign objects and nger marks on the lens can cause inferior image quality in low light level
conditions
When using an auto iris lens
1. Please peel off about 8mm of the outer skin of the auto iris lens cable.
2. Please peel off about 2mm of the outer skin of the insulated conductor inside the lens cable.
3. Please remove the cover of the auto iris connection plug and solder
The lens cable to the connector pin in plug.
* PIN ASSIGNMENT OF THE LENS CONNECTOR
DC auto iris lens
Pin 1 : DAMP-(CTL-)
Pin 2 : DAMP+(CTL+)
Pin 3 : DRV+
Pin 4 : DRV-(GND)
4. Please replace the auto iris lens connection plug cover and take off the CIS protection cap and then
attach the auto iris to the camera by Screwing it in clockwise.
5. Please insert the connection plug that is connected to the auto iris lens Cable into the auto lens
connector, which is located on the side of the Camera.
Installation of C-Mount Lens
KNC-Xi210HD
Installation Guide
C-Mount
Adaptor ring
Software CD
Installation of CS-Mount Lens
Auto Iris Lens
Connection Plug
How to connect video and audio
Microphone
DC12VorAC24V
Adaptor
SD Card
Speaker
Reset Switch/
NTSC or PAL select
3. When the Network Camera appears in the window, select the Network Camera which needs to
assign the IP address.
A. Refresh Device List – Rescan local network to nd the Network Camera.
B. Authenticate – Enter the administrator ID and password.
C. Host Name – Enter the Host Name of the Network Camera.
D. IP Settings
i. Dynamic – Assign dynamic IP address automatically from DHCP server on your network.
ii. Static – Assign static IP address manually.
iii. Port – Enter the HTTP port the Network Camera will use. The default setting is 80.
Alternatively, any port in the range 1024-65535 may be used, but check rst with your
system administrator before changing the default setting.
E. Network Settings
i. Subnet Mask – Specify the mask for the subnet the Network Camera located on.
ii. Gateway – Specify the IP address of the default router (gateway) used for connecting devices
attached to different networks and network segments.
iii. Pri. DNS – Enter the IP address of the primary DNS server. This server provides the
translation of host names to IP addresses on your network.
iv. Sec. DNS – Specify the IP address of the secondary DNS server. This will be used if the
primary DNS server is unavailable.
4. Click “Set” button to save conguration.
8. The video image displays in your browser.
Note:
To view streaming video in Microsoft Internet Explorer, you must set your browser to allow the “KT&C Web
Viewer” to be installed on your computer. This ActiveX component is installed the first time a video stream is
accessed.
1. Optionally connect a microphone or line in mono signal to the Line in/MIC connector.
2.Optionally connect a speaker to Line out connector.
3. Optionally insert a Micro SD card to Micro SD socket.
4. Connect the camera to the network using a UTP cable (CAT.5), Power can be supplied via the
network cable (PoE)
5. Connect DC 12V or AC 24V to the power terminal. This is not necessary if the Network Camera is
connected to PoE hub or midspan. Caution: Do not apply DC 12V and AC 24V at the same time.
CAUTION
6. Check that the indicator LEDs indicates the correct conditions.
7. Connect the analog monitor to the service video connector for adjusting focus and press and quickly
release the reset switch for focus assistant mode. Then you can select normal view or focus view
mode using the reset switch.
CAUTION
for more exact focus.
CAUTION
for normal operation.
: Do not apply DC 12V and AC 24V at the same time.
: When you use focus assistant mode, “Focus View” mode is recommended
: Focus assistant mode will be automatically exited after 3 minutes
5. Assign an IP address
To make it accessible on the network, the Network Camera must be assigned an IP address.
Note:
•
A network DHCP server is optional.
•
The Network Camera has the default IP address 192.168.0.123.
•
If IP assignment fails, check that there is no firewall blocking its operation and check that the Network
Camera and your computer's IP is located on the same subnet.
Accessing the Network Camera
1. Start your browser.
2. Enter the IP address or host name of the Network Camera in the Address eld of your brows
3. If you are accessing the Network Camera for the rst time, you will see the following warning
message as shown below.
4. Click the warning message and select “Install ActiveX Control…”.
5. Click “Install” to install the KT&C Web Viewer.
6. If a Windows Security Alert pop-up appears, click “Unblock”.
6. Terminal Block Connectors
KNC-Xi210HD is connected with external equipment as following diagram below.
Circuit diagram
KNC-Xi120HD
1. INPUT – Connect the external sensor e.g. PIR motion sensor. (3.3V DC pull-up built in)
A. ON - Short-circuit with GND.
B. OFF - Open
CAUTION
2. OUT – Connect the external alarm e.g. light or buzzer.
CAUTION
with the load, for protection against voltage transients.
CAUTION
Digital Input must not be exposed to voltages greater than 10V DC.
:
If used with an external relay, a diode must be connected in parallel
:
Max. load = 70mA Max voltage = 12V DC.
:
Assign an IP address using IP Installer
IP installer automatically search and display KT&C network devices on your
network. The application can also be used to manually assign a static IP address.
Note:
The computer running the IP installer must be on the same network segment (physical subnet) as the Network
Camera.
1. Check that the Network Camera is connected to the network and that power has been applied.
2. Start KT&C IP installer.
Example of terminal connection
7. After installing the KT&C Web View ActiveX Control, a Login page will be displayed.
Enter the user ID and password.
Note:
Default User ID and Password is [ID: admin, Password: admin]
Loading...