Page 1
• DC 12V
• DUAL(DC 12V/AC24V)
When you install the camera, please glue up the end of cable to
keep it stable in order to protect the camera from the humidity problems.
CONNECTION
DC12V
REGULATED POWER SUPPLY
BNC FEMALE
VIDEO
VIDEO IN
DC12V / AC24V
REGULATED POWER SUPPLY
BNC FEMALE
VIDEO
VIDEO IN
AR M O RE D DO M E C A M ER A
OP E R AT IO N MA N UA L
M05 1-VDQ 100 -002
Thank you for choosing our high quality camera.
Before attempting to connect or operate, please read and follow
these instructions.
This device complies with Part 15 of the FCC Ru le s.
Operation is subject to the following two conditions;
1. Th is d evi ce ma y not ca us e har mfu l in ter fe re nce .
2. Th is d evi ce mu st ac cep t an y i nte rf er enc e re cei ved , in clu din g
i nt er fer en ce th at ma y cau se un de sir ed o per ati on .
This equipment has been tested and found to comply with limits for a Class B digital
device, pursuant to part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a residential installation.
This equipment generates, uses, and can radiate radio communications.
However, there is no guarantee that interference will not occur in a particular installation.
If this equipment off and on, the user is encouraged to try to correct the interference by
one or more of the following measures:
Note -
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio / tv technician for help.
Any changes or modi cations in cons truction of thi s device which are not expressly
approved by the party respons ible f or com pliance could void the us er's a uthority to
operate the equipment.
Caution -
1. A regulated DC12V 3A power supply is recommended for use with this camera
for the best picture and the most stable operation.
An unregulated power supply can cause damage to the camera.
When unregulated power supply is applied, product warranty will be
out of subject.
2. It is recommended that the camera is used with a monitor that has a CCTV quality
75 video impedance level.
If your monitor is switched to high impedance then please adjust accordingly.
3. Do not attempt to disassemble the camera to gain access to the internal
components. Refer servicing to your dealer.
4. Never face the camera towards the sun or any bright or reective light, which may
cause smear on the picture and possible damage to the CCD.
5. Do not remove the serial sticker for the warranty service.
Correct Disposal of This Product
(Waste Electrical & Electronic Equipment)
(Applicable in the European Union and other European countries with separate collection systems)
This marking shown on the product or its literature, indicate that it should not be disposed with
other household wastes at the end of its working life. To prevent possible harm to the environment
or human health from uncontrolled waste disposal, please separate this from other types of wastes
and recycle it responsibly to promote the sustainable reuse of material resources.
This product should not be mixed with other commercial wastes purchased this product, or their
local government ofce, for details of where and how they can take item for environmentally safe
recycling.
Business users should contact their supplier and check the terms and conditions of the purchase
contract.
Household users should contact either the retailer where they for disposal.
SPECIFICAT I O N S
Signal Format NTSC PAL
Image Device 1/3" Sony Super HAD CCD
Ⅱ
Scanning System 2:1 Interlace
H.Resolution 550TV Lines
Scanning Frequency H:15.734KHz, V:59.94Hz H:15.625KHz, V:50Hz
Total Pixels 811(H) x 508(V) 795(H) x 596(V)
Effective Pixels 768(H) x 494(V) 752(H) x 582(V)
Electronic Shutter Speed 1/60 sec 1/50 sec
S/N Ratio More than 45dB(AGC Off)
Gnmma Correction r=0.45
Min. Illumination 0.05 Lux / Face Plate
Sync. System Internal
Second Video Connector 1.0 Vp-p Composite 75(Ω)
Input Power
Source
DC12V DC12V (±10%), Max. 180mA
Dual
Voltage
• DC12V (±10%), Max. 250mA
• AC24V (±10%), Max. 3W
Operating Temperature -10℃ ~ +50
℃
Storage Temperature -20℃ ~ +60
℃
Operating Humidity Less then 80%
IP Rating IP66(Weatherproof)
Weight Approx. 870g
Input Power
Source
DC12V DC12V (±10%), Max. 800mA
Dual
Voltage
• DC12V (±10%), Max. 930mA
• AC24V (±10%), Max. 20W
Min. Illumination 0 Lux (IR LED ON)
IR LED 22ea
IR LED Half Angle ±22 Degree
IR LED Wavelenght 850nm
IR Ream Length Up to 30m
IR LED Operation ON : 3 Lux, OFF : 6 Lux
LED TYPE
STA N DARD TYPE
Face P late : Point at the CCD without obstruct ion of light from an y other material.
DC +12V or AC24V
MALE(Red)
VIDEO
BNC FEMALE(Yellow)
AUDIO
RCA FEMALE(White)
• AUDIO •UTP
DC +12V or AC24V
MALE(Red)
VIDEO
BNC FEMALE(Yellow)
UTP
(AWG - size: #26)
CABLE OPTION
Page 2
1. Installation of Flush Mount
①
Installation of the camera with SURFACE CASE(using M4x40)
②
Installation of the camera with SCREWS
③
Installation of the camera with JUNCTION BOX
2. Installation of Surface Mount
①
Installation of the camera on the wall
②
Installation of the camera on the 3/4” NPT PIPE
③
Installation of the camera on the JUNCTION BOX
3-AXIS GIMBAL BRAC K E T
ACCESSORIES FURNISHED
Accessories
Video output
test cable
Screw Wrench
Manual Mount Guide
M4x10 5x35 M4x10.SUS T20
Q'ty 1 4 4 4 1 1 1
Option - - - - - - -
Ove r v i e w
Di p Sw i t ch s
1
ATW
(Automatic Tracing
White Balance)
ON : ATW
OFF : PUSH
2
F/L
(FLICKERLESS)
ON / OFF
3
AGC
(Automatic Gain Control)
ON : MIN
OFF : MAX
4
N.C
-
Se r v i c e V i deo con n ect o r
The Service Video
Connector also provides
the installer with an easy
way of conguring the
camera.
DIMENSIONS
Unit : mm
Camera Mounting Position
Na m e a n d F u n ct i o n
When you x the focus around 22.0mm in f9.0-22.0mm Varifocal lens, please
set short distance focus approximately 3m and do not set long distance focus
Check the safe wire which
should be enti rely inserted into
camera housing during locking
th e dom e cov er to m aint ain
Waterproof condition.
NOT E
When using the camera
without LED take off the rubber.
Pan
Horizontal Rotation
Tilt
When using the camera.
Surface Mount Type
Flush Mount Type
Type A Type B
Loading...