KT&C KPC-VDN101, KPC-VDN102 Operation Manual

Thank you for choosing our high quality camera.
Before attempting to connect or operate, please read and follow
these instructions.

OPE R AT I ON M ANU A L

HIGH RESOLUTION

ARMORED DOME CAMERA

M063-VDN101-002

CO NT EN TS

1. C aut i ons

2. F eat u res

3. P ack a ge

4. O ver v iew and fun c tio n

5. I nst a lla t ion

6. C onn e cti o n

7. D ime n sio n s

8. S pec i fic a tio n s

9. S etu p me n u o p era t ion

• SETUP MENU

• SETUP MODE

• CAMERA ID

• LENS

• SHUTTER

• WHITE BALANCE

• LANGUAGE MODE SETUP

• RESET

10. F unc t ion Men u op e rat i on

• FUNCTION MENU

• BLC

• AGC

• DAY&NIGHT

• PRIVACY

• MIRROR

• GAMMA

• MOTION

11. T rou b les h oot i ng

3

1. Ca ut io ns

4

This device complies with Part 15 of the FCC Rules.
Operation is subject to the following two conditions;

1. This device may not cause harmful interference.

2. This device must accept any interference received, including
interference that may cause undesired operation.

This equipment has been tested and found to comply with limits for a Class B digital
device, pursuant to part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a residential installation.
This equipment generates, uses, and can radiate radio communications.
However, there is no guarantee that interference will not occur in a particular
installation. If this equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:

Note -

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and receiver.

• Connect the equipment into an outlet on a circuit different from that to
which the receiver is connected.

• Consult the dealer or an experienced radio / tv technician for help.

Any changes or modications in construction of this device

which are not expressly approved by the party responsible
for compliance could void the user's authority to operate the
equipment.

Caution -

1. A regulated DC12V 1.5A power supply is recommended for use with this camera
for the best picture and the most stable operation.
An unregulated power supply can cause damage to the camera.

When unregulated power supply is applied, product warranty will be
out of subject.

2. It is recommended that the camera is used with a monitor that has a CCTV quality
75 video impedance level.
If your monitor is switched to high impedance then please adjust accordingly.

3. Do not attempt to disassemble the camera to gain access to the internal
components. Refer servicing to your dealer.

4. Never face the camera towards the sun or any bright or reective light, which may

cause smear on the picture and possible damage to the CCD.

5. Do not remove the serial sticker for the warranty service.

Correct Disposal of This Product

(Waste Electrical & Electronic Equipment)

(Applicable in the European Union and other European countries with
separate collection systems)

This marking shown on the product or its literature, indicate that it should not
be disposed with other household wastes at the end of its working life. To
prevent possible harm to the environment or human health from uncontrolled
waste disposal, please separate this from other types of wastes and recycle it
responsibly to promote the sustainable reuse of material resources.

This product should not be mixed with other commercial wastes purchased this

product, or their local government ofce, for details of where and how they can

take item for environmentally safe recycling.

Business users should contact their supplier and check the terms and
conditions of the purchase contract.
Household users should contact either the retailer where they for disposal.

1. Ca ut io ns

5

CAUTIONS

1

2. Fe at ur es

6 7

• Sony 1/3” Super HAD CCD

Ⅱ

• 550TV Lines

• OSD Function

• Manual shutter

• Privacy Zone

• Dual Voltage use DC12V/AC24V

• Motion Detection

• 3-Axis Gimbal

The S ervice V ideo C o nnecto r also pr o v i d e s t h e installer w i t h a n
easy way of configuring the camera.

• Service Video connector

Pan Rotation Horizontal RotationTilt Rotation

CAUTION panning the bracket in excess of 3 rotations in one direction may
cause damage to the cable.

FEATURES

2

CAUTIONS

1

3.

Pa ck ag e

1 ARMORED DOME CAMERA

2 SURFACE MOUNT

3 VIDEO OUTPUT TEST CABLE

4 OPERATION MANUAL

5

SCREW(M4x10) - 4ea
SCREW(5x30) - 4ea
SCREW(M4x40.SUS) - 4ea

L WRENCH - T20

6 MOUNT GUIDE

4. Ov er vi ew a nd f un ct io n

• CONTROL FUNCTION

(OSD JOYSTICK)

LEFT

UP

RIGH T

DOWN

MENU

• Name (LED Type)

• Name (Standard)

8 9

5. I ns ta ll at io n

Standard TypeLED Type

Mount Guide

5. I ns ta ll at io n

10

1. Installation of Flush Mount

2. Installation of Surface Mount

PIPE

PIPE

①

Installation of the camera with SURFACE

CASE(using M4x40)

②

Installation of the camera with SCREWS

③

Installation of the camera with JUNCTION BOX

①

Installation of the camera on the wall

②

Installation of the camera on the 3/4” NPT PIPE

③

Installation of the camera on the JUNCTION BOX

Check the safe wire which

should be entirely inserted into camera

housing during locking the dome cover to

maintain Waterproof condition.

When using the camera

without LED take off the rubber.

NO T E

6. Co nn ec ti on

11

When you install the camera, please glue up the end of cable to
keep it stable in order to protect the camera from the humidity problems.

• DUAL(DC 12V/AC24V)

• DC 12V

7. Di me ns io ns

Unit : mm

45

˚

70

˚

Standard Type LED Type

12

When you x the focus around 22.0mm in f9.0-22.0mm Varifocal lens, please

set short distance focus approximately 3M and do not set long distance focus

Surface Mount Type

Flush Mount Type

Type A

Type B

8. Sp ec if ic at io ns

Signal Format NTSC PAL

Image Device

1/3" Sony Super HAD CCD

Ⅱ

Scanning System 2:1 Interlace

H.Resolution 550TV Lines

Scanning Frequency H:15.734KHz, V:59.94Hz H:15.625KHz, V:50Hz

Total Pixels 811(H) x 508(V) 795(H) x 596(V)

Effective Pixels 768(H) x 494(V) 752(H) x 582(V)

Electronic Shutter Speed 1/60 sec 1/50 sec

S/N Ratio More than 48dB(AGC Off)

Gamma r=0.45

Min. Illumination 0.05 Lux / Face Plate

Sync System Internal

Video Output 1.0 Vp-p Composite 75(Ω) unbalanced

Power
Consumption

DC12V DC 12V (±10%) Max 110mA

Dual

DC 12V (±10%) 160mA

AC 24V (±10%) 170mA / 1.8W

Operating Temperature -10℃ ~ +50

℃

Storage Temperature -20℃ ~ +60

℃

Operating Humidity 10% ~80%

Options Dual Power, Fan

Weight

• Surface Mount Type A : Approx. 1.38kg /
Type B : Approx.

1.1kg

• Flush type : Approx. 730g

Power
Consumption

DC12V DC 12V (±10%) Max 400mA

Dual

DC 12V (±10%) 540mA

AC 24V (±10%) 440mA / 5.5W

Min. Illumination 0 Lux (IR LED ON)

IR LED 30ea

IR LED Half Angle ±22 Degree

IR LED Wavelenght 850nm

IR Beam Range Up to 30 m

IR LED Operation On : 1 Lux, Off : 3 Lux

LED TYP E

13

Face Plate : Point at the CCD without obstruction of light from any other material.

9. Se tu p me nu o pe ra ti on

OSD STRUCTURE

•

▲,▼ :

Menu up / down

•

◀

,▶ :

Set-up Key

•

■

:

MENU

(SEL E C TION K EY)

14 15

SETUP MENU

CAMERA ID • ON • OFF

LENS • MANUAL • VIDEO • DC

SHUTTER • AUTO • FLK • FIXED • MANUAL

WHITE BAL. • ATW • AWB • FIXED • MANUAL

FUNCTION

• BLC • AGC • DAY & NIGHT • PRIVACY

• MIRROR • GAMMA • MOTION

ADJUST

• CONTRAST • SHARPNESS

• CB_GAIN • CR_GAIN

LANGUAGE • ENGLISH • KOREAN • CHINESE1 • CHINESE2 • JAPANESE

RESET • YES • NO

EXIT

9. Se tu p me nu o pe ra ti on

1)SETUP mode

- Press and hold MENU button 1 second to access the setup mode.

SETUP menu is displayed on the monitor.

①

Select OSD item using UP, DOWN button.

②

Set details using LEFT, RIGHT button.

③

Select “EXIT” and then press the MENU

button to nish the SETUP.

(Save and Exit)

2)CAMERA ID

- Select CAMERA ID using UP, DOWN button

in SETUP menu.

- Set ON state using LEFT, RIGHT button.

- Press MENU button in CAMREA ID.

ID SETUP menu is displayed on the monitor.

2-1) CAMERA ID setup

①

Character is changed each time UP, DOWN button is pressed.

(You can select up to 63 letters)

②

Character position is changed LEFT, RIGHT button is pressed.

③

Press MENU button in to exit from ID setup mode

④

Press MENU button in ‘C’ to correct and erase the chosen entry.

2-2) POSITION setup.

①

Press POSITION

②

Move the character position using UP, DOWN, LEFT, RIGHT button.

③

Press MENU button to conrm the position of the character.

④

Press MENU button in RETURN to go to previous screen.

ID is displayed by pressing EXIT on SETUP menu.

9. Se tu p me nu o pe ra ti on

16 17

3)LENS

3-1) LENS setup

Press LEFT or RIGHT button in LENS on SETUP menu to select the mode to
MANUAL

󰆋󰆍

VIDEO

󰆋󰆍

DC

󰆪

3-2) DC LENS setup (IRIS LEVEL setup)

①

Press MENU button in DC

󰆪

to display the screen.

②

Use LEFT, RIGHT button to change

BRIGHTNESS(IRIS LEVEL)value.

③

Press MENU button to return

to the previous screen.

4)SHUTTER

4-1) SHUTTER setup

Press LEFT or RIGHT button in SHUTTER to select the mode to
AUTO󰆪

󰆋󰆍

FLK

󰆋󰆍

FIXED

󰆪󰆋󰆍

MANUAL

󰆪

4-2) SHUTTER AUTO setup (AE LEVEL setup)

①

Press MENU button in AUTO

󰆪

to display the screen.

②

Use LEFT, RIGHT button to change

BRIGHTNESS(AE LEVEL) value.

4-3) SHUTTER FIXED setup (MANUAL, DC, VIDEO LENS)

①

Press MENU button in FIXED󰆪

①

Press LEFT or RIGHT button in SHUTTER.
You can be set in
1/60(NTSC), 1/50(PAL) ~ 1/100,000 range.

9. Se tu p me nu o pe ra ti on

4-4) SHUTTER MANUAL setup(MANUAL, DC, VIDEO LENS)

①

Press MENU button in MANUAL

󰆪

②

Press LEFT or RIGHT button in SHUTTER M.
SHUTTER M. value is changed

between 0<MIN> ~ 255<MAX>.

0<MIN>:1/50 or 1/60,

255<MAX>:1/100,000

5)WHITE BALANCE

5-1) WHITE BALANCE setup

Press LEFT or RIGHT button in WHITE BAL. to select the mode to
ATW

󰆋󰆍

AWB

󰆋󰆍

FIXED󰆪

󰆋󰆍

MANUAL

󰆪

5-2) AWB FIXED setup

①

Press MENU button in FIXED󰆪.

②

Press LEFT or RIGHT button.
You can set from MODE 1 to MODE 4.

5-3) AWB MANUAL setup

①

Press MENU button in MANUAL󰆪.

②

Press LEFT or RIGHT button
in RED or BLUE.
Set Red and Blue color temperature value.

9. Se tu p me nu o pe ra ti on

18 19

6)ADJUST Mode Setup

6-1) ADJUST setup

①

Press MENU button in ADJUST󰆪.

②

Press UP or DOWN button
to select the mode.

③

Each level value can be adjusted
using LEFT, RIGHT button.

6-2) CONTRAST setup
Adjust Y-gain value(0~255)

6-3) SHARPNESS setup

Adjust aperture value(0~31)

6-4) CB_GNIN setup
Adjust COLOR CB_GAIN value(0~255)

6-5) CR_GAIN setup
Adjust COLOR CR_GAIN value(0~255)

7)LANGUAGE Mode Setup

①

DEFAULT value – ENGLISH

②

After selection LANGUAGE, change setting using LEFT or RIGHT button.

③

Choose the language mode you wish to operate in
ENGLISH

󰆋󰆍

Korean

󰆋󰆍

Chinese1

󰆋󰆍

Chinese2

󰆋󰆍

Japanese

8)RESET

①

Press MENU button in RESET.

②

Select YES to reset your camera
to default factory condition

10 .F un ct io n Me nu o pe ra ti on

1)FUNCTION menu

- Press MENU button in FUNCTION

󰆪.

on SETUP menu.

①

Select item using UP, DOWN button.

②

Set details using LEFT, RIGHT button.

③

Press MENU button in RETURN
to go to SETUP menu.

2)BLC

2-1) BLC SETUP mode

- Press MENU button in BLC ON󰆪.

2-2) BLC AREA setup

①

Use UP,DOWN,LEFT,RIGHT button
to move the AREA setup position.

②

Set or release BLC AREA
using MENU button.

③

Press MENU button for more than 1 second
to move to BLC AREA MODE

10 .F un ct io n Me nu o pe ra ti on

20 21

2-3) BLC AREA MODE

①

ALL CLEAR – Clear all set AREA

②

ALL SET – Set all 64 BLC AREA

③

RETURN – Return to BLC AREA
setup mode.

④

EXIT – Save AREA and
return to BLC SETUP mode.

2-4) BLC RATIO setup

①

Use UP, DOWN button
to move to BLC RATIO.

②

Use LEFT, RIGHT button
to change BLC LEVEL value(0~63)
0:MIN, 63:MAX

③

Press MENU button in RETURN
to move to FUNCTION MODE.

3)AGC

①

AGC default setting ON󰆪.

②

Press MENU button in ON󰆪.

③

Use LEFT, RIGHT button

to adjust AGC GAIN value(0~255)
0:MIN, 255:MAX

④

Press MENU button in RETURN
to the previous screen.

10 .F un ct io n Me nu o pe ra ti on

4)DAY & NIGHT (STANDARD TYPE Only)

- Press LEFT or RIGHT button in DAY NIGHT select the mode to

AUTO 󰆪

󰆋󰆍

B/W󰆪

󰆋󰆍

COLOR.

4-1) AUTO 󰆪 mode setup

- Press MENU button in AUTO󰆪 mode.

- Select item using UP/DOWN button.

- Adjust value using LEFT/RIGHT button.

- Press MENU in RETURN to return

to the previous screen

NOTE) Auto mode does not operate in
True D&N Type but operate in Standard type.
NOTE) When AGC mode is turned off, AUTO mode does not operate.
NOTE) The camera of True D&N type in Day & Night function is under
the control of photocell

①

DELAY

DAY  NIGHT or NIGHT  DAY conversion time setup
0 : No DAY NIGHT AUTO conversion
1~63 : Can set from 1 second to 15 seconds

②

START LEVEL

DAY  NIGHT conversion illumination intensity setup 0~255

0 : High illumination intensity, 255 : Low illumination intensity

NOTE) Initial value setup is recommended.

③

END LEVEL

NIGHT  DAY conversion illumination intensity setup 0~255

0 : High illumination intensity, 255 : Low illumination intensity

NOTE) Initial value setup is recommended.

4-2) B/W󰆪 mode setup

①

Press MENU in B/W󰆪.

②

Move to screen on the right side.

③

Use LEFT, RIGHT button

to set BURST ON/OFF.

④

After setup, return to the previous screen

by pressing MENU button.

10 .F un ct io n Me nu o pe ra ti on

22 23

5)PRIVACY

5-1) PRIVACY setup

①

Default setting OFF

②

Using LEFT, RIGHT button, change setup to ON󰆪 mode.

③

After ON󰆪 mode setup, 4 AREA groups are congured as displayed
on the bottom picture.

④

Press MENU button.
Details of each area is displayed.

5-2) PRIVACY details setup

①

Select AREA SEL – PRIVACY 0~3

②

AREA STATE – 0~3 AREA ON/OFF

③

LEFT – Change left portion of each AREA size.

④

RIGHT – Change right portion of each AREA size.

⑤

TOP – Change top portion of each AREA size.

⑥

BOTTOM – Change bottom portion of each AREA size.

⑦

COLOR – Change entire color of the AREA(16 COLOR)

10 .F un ct io n Me nu o pe ra ti on

6)MIRROR

①

MIRROR default setting OFF
ON setting – Use LEFT, RIGHT button.

②

Left and Right side is switched as shown on the picture.

7)GAMMA

7-1) GAMMA setup (DEFAULT 0.45)

①

In FUNCTION MODE, use UP,DOWN button to select GAMMA.

②

Use LEFT, RIGHT button to adjust GAMMA value.
USER

󰆋󰆍

0.05

󰆋󰆍

0.10

󰆋󰆍

0.15 ~ 1.0

10 .F un ct io n Me nu o pe ra ti on

24

8)MOTION

8-1) MOTION setup

①

DEFAULT value OFF

②

In ON󰆪, press MENU button.

③

Display MOTION details.

8-2) AREA󰆪 setup

In AREA󰆪 , press MENU button.

8-2-1) MOTION AREA setup

①

Use UP, DOWN, LEFT, RIGHT button
to move AREA setting position.

②

Use MENU button to set and release AREA.

③

Press MENU button for more than 1 second
to move to MOTION AREA mode

8-2-2) MOTION AREA mode

①

ALL CLEAR – Clear all set AREA

②

ALL SET – Set all 64 MOTION AREA.

③

RETURN – Return to MOTION AREA
setup mode.

④

EXIT – Save AREA and
return to MOTION setup mode.

8-3) MOTION TH. Setup

①

Set motion sensitivity 0(MAX)~255(MIN)

8-4) MOTION TRACE setup

①

ON : Display motion detection AREA.

11. Tro ub le sh oo ti ng

25

If there are problems in operation, please refer to the items below.
If the problem persists, please contact the agent you purchased this
product from.

Problems Troubleshooting

Nothing appears on the screen.

• Please check the power connection.

• Please check the video signal line connection.

The video image is not clear.

• Please check if the lens is clean.
Please clean the lens with a clean cloth or brush.

• Please adjust the contrast feature of the monitor.

• Please readjust the back focus of the camera.

The screen is dark.

• Please adjust the contrast feature of the monitor.

• If you have an intermediate device,

set the 75 / Hi-z properly, and check the terminals.

• Please check if an auto iris lens is being used and
adjust the brightness level.

There is a problem with the
camera operation.

• Please check if an appropriate power source to the
camera complies with the manufacturer's standard
requirement, or if the voltage keeps changing.

Colors are not quite right. • Please check the 'WHITE BAL' setting

The screen is ickering.

• Please check if the camera is facing directly into

sunlight or uorescent light.

• Please check if an auto iris lens is being used.

• Please check the connection of the lens
connector cable.

AUTO mode in DAY & NIGHT
function is not working.

• Please check if the DAY & NIGHT function
is set to the AUTO position.

DAY & NIGHT function is not
working.

• Please check if the AGC menu is set to the
ON position.