KT&C KPC-ND521NU User Manual

KPC-ND521NU

Resolution 960 Series 750+ HTVL
IP66 IR Ball Camera

OPERATION MANUAL

KPC-ND521NUB: Resolution 960 IR IP66 Ball Camera 750+ HTVL

12VDC 66’ range, with DWDR and DNR (NTSC) Black color

KPC-ND521NUW: Resolution 960 IR IP66 Ball Camera 750+ HTVL

12VDC 66’ range, with DWDR and DNR (NTSC) While color

Thank you for choosing our high quality camera.
Before attempting to connect or operate this unit, please read and follow these instructions.

KEY FEATURES

* Superlative resolution of over 750 horizontal TV lines for amazing image quality
* Flexible positioning for convenient wall or ceiling mounting
* 3.6mm lens to capture the desired field of view
* Equipped with 20 IR LEDs for 66 foot/20m range (depending on scene IR reflectivity)
* Exview HAD II sensor delivers amazing low light sensitivity before IR illumination
* Reflection preventing dual section cover glass isolates IR emitters from lens to prevent image

distortion

* IP66 vandal & weather resistant
* Adaptive Tone Curve Reproduction ATR/Digital Wide Dynamic Range expansion to deliver

properly exposed images despite unbalanced lighting in the scene

* 2D-Noise Reduction increases picture clarity while improving DVR disk storage utilization
* ATW with Anti-Color Roll for stability under fluorescent lighting
* Low current draw 12VDC operation with Anti Color Roll for stability even without line lock

ACCESSORIES FURNISHED

Accessories Screw Plastic Anchors Template Manual

Q'ty 4 4 1 1

www.ktncusa.com

SPECIFICATIONS

Signal Format NTSC
Image Device 1/3” 960H SONY EXview HAD CCD II
H.Resolution 750+TV Lines
Total Pixels / Effective Pixels 1020(H) X 508(V) / 976(H) X 494(V)
Electronic Shutter Speed 1/60~1/100,000sec
S/N Ratio More than 50dB(AGC OFF)
Gamma r =0.45
Min. Illumination 0 Lux (IR LED ON)
Sync System Internal with Anti-Color Roll
Video Output
2D DNR AUTO
ATR / DWDR AUTO
White Balance ATW with Anti-Color Roll
AGC AUTO
Day & Night Digital Day & Night
Lens Board Lens (f=3.6mm / F=2.0)
IR LED 850nm, 20ea
IR LED Distance 66’ (20 m)
IR LED Half Angle ±22 Degree
IP Rating IP66
Power
Consumption
Operating Temperature 14°F~122°F (-10°C~+50°C)
Storage Temperature -4°F~140°F (-20°C~+60°C)
Weight Approx. 11.29 Ounce
Manual Pan & Tilt Pan 360° / Tilt 140°
Dimension 3.66(Ø) * 2.76 inches

KT&C America, Inc. reserves the right to make changes to improve our products at any time without notice;
we are not responsible for misprints.

1.0 Vp-p Composite 75(Ω) unbalanced

DC12V (±10%),

Max. 300mA (IR LED ON) / Max. 80mA (IR LED OFF)

DIMENSIONS

Unit : Inches (mm)

Ø 3.66” (93 mm)

20 - IR LED

Ø 2.72” (69 mm)

<Top View>

Approx. 2.76” (70 mm)

<Front View>

<Side View>

CAMERA MOUNTING POSITION

Tiilt: 70° Tiilt: 70°140°

CONNECTION

CCTV Camera

3.31” (84 mm)

(The maximum rotation)

Tapping Screws-4x25L(4ea)

DC12V

(DC Jack)

BNC Female

Video In

Open

Template

DC12V
Adapter

TV

Monitor

4 - Ø 0.18” (4.5 mm)

2.69” (68.5 mm)

<BOTTOM View>

Plastic Anchors (4ea)

Close

“When installing the camera, to insure reliable operation please seal well/protect the
power and video connections from moisture.”

This device complies with Part 15 of the FCC Rules.
Operation is subject to the following two conditions;

1. This device may not cause harmful interference.

2. This device must accept any interference received, including interference that may cause undesired operation.

Note

This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part
15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference
when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate
radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause
harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause
harmful interference in which case the user will be required to correct the interference at his own expense.”

WARNING

This is a class A product. In a domestic environment this product may cause radio interference in which case the
user may be required to take adequate measures.

Caution

Any changes or modifications in construction of this device which are not expressly approved by the party
responsible for compliance could void the user’s authority to operate the equipment.

1. To obtain best picture quality and most stable operation, a regulated DC12 500mA
power supply is recommended to power this camera. An unregulated power supply may

damage to the camera, and its use may void the product warranty.

2. It is recommended that the camera is used with a monitor that has a CCTV quality
75 video impedance level.
If your monitor is switched to high impedance then please a djust accordingly.

3. Do not attempt to disassemble the camera to gain access to the internal components.
Refer servicing to your dealer.

4. Never face the camera towards the sun or any bright or reflective light, which may
cause smear on the picture and possible damage to the CCD.

5. Do not remove the serial number sticker; it is required to obtain warranty service.