KT&C KPC-N751NU User Manual

M145-N751-001

HIGH PERFORMANCE

Super Night Vision Camera

OPERATION MANUAL

HIGH
POWER

LED

Thank you for choosing our high quality camera. Before attempting
to connect operate this unit,please read and follow these instructions.

CAUTION

These servicing instructions are for use by qualied service personnel only.
To reduce the risk of electric shock do not perform any servicing other than
that contained in the operating instructions unless you are qualied to do so.

Use Class 2 Power Supply Only

2

CONTENTS

1. CAUTIONS

2. IMPORTANT SAFETY INSTRUCTIONS

3. FEATURES

4. COMPONENTS

5. NAME AND FUNCTION

6. INSTALLATION

7. DIMENSIONS

8. SPECIFICATION

9. OSD MANUAL

10. COMMUNICATION PROTOCOL

3

1. CAUTIONS

This device complies with Part 15 of the FCC Rules.
Operation is subject to the following two conditions;

1. This device may not cause harmful interference.

2. This device must accept any interference received, including
interference that may cause undesired operation.

Note

This equipment has been tested and found to comply with the limits for a Class A digital
device, pursuant to part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference when the equipment is operated
in a commercial environment. This equipment generates, uses, and can radiate radio
frequency energy and, if not installed and used in accordance with the instruction
manual, may cause harmful interference to radio communications. Operation of this
equipment in a residential area is likely to cause harmful interference in which case the
user will be required to correct the interference at his own expense.”

WARNING

This is a class A product. In a domestic environment this product may cause radio
interference in which case the user may be required to take adequate measures.

Caution

Any changes or modications in construction of this device which are not expressly

approved by the party responsible for compliance could void the user’s authority to
operate the equipment.

1. A regulated DC12V 1A power supply is recommended for use with this camera
for the best picture and the most stable operation.
An unregulated power supply can cause damage to the camera.

When unregulated power supply is applied, product warranty will be
out of subject.

2. It is recommended that the camera is used with a monitor that has a CCTV quality
75 video impedance level.
If your monitor is switched to high impedance then please adjust accordingly.

3. Do not attempt to disassemble the camera to gain access to the internal componets.
Refer servicing to your dealer.

4. Never face the camera towards the sun or any bright or reective light, which may

cause smear on the picture and possible damage to the CCD.

5. Do not remove the serial sticker for the warranty service.

4

1. CAUTIONS

Correct Disposal of This Product

(Waste Electrical & Electronic Equipment)

(Applicable in the European Union and other European countries with

separate collection systems)

This marking shown on the product or its literature, indicate that it should not
be disposed with other household wastes at the end of its working life. To
prevent possible harm to the environment or human health from uncontrolled
waste disposal, please separate this from other types of wastes and recycle it
responsibly to promote the sustainable reuse of material resources.

This product should not be mixed with other commercial wastes purchased this

product, or their local government ofce, for details of where and how they can

take item for environmentally safe recycling.
Business users should contact their supplier and check the terms and

conditions of the purchase contract.
Household users should contact either the retailer where they for disposal.

CAUTION

RISK OF ELECTRIC SHOCK DO NOT OPEN

CAUTION:

TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT
REMOVE COVER (OR BACK). NO USER. SERVICEABLE
PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE
PERSONNEL

This symbol is intended to alert the user to the presence of un­insulated “dangerous voltage” within the product’s enclosure that

may be of sufcient magnitude to constitute a risk of electric shock

to persons.

This symbol is intended to alert the user to the presence of
important operating and maintenance (servicing) instructions in the
literature accompanying the appliance.

5

2. IMPORTANT SAFETY INSTRUCTION

1) Read these instructions.

2) Keep these instructions.

3) Heed all warnings.

4) Follow all instructions.

5) Do not use this apparatus near water.

6) Clean only with dry cloth.

7) Do not block any ventilation openings. Install in accordance
with the manufacturer’s instructions.

8) Do not install near any heat sources such as radiators, heat registers,

stoves, or other apparatus (including ampliers) that produce heat.

9) Do not defeat the safety purpose of the polarized or grounding-type plug. A
polarized plug has two blades with one wider than the other. A grounding type plug
has two blades and a third grounding prong. The wide blade or the third prong are

provided for your safety. If the provided plug does not t into your outlet, consult an

electrician for replacement of the obsolete outlet.

10) Protect the power cord from being walked on or pinched particularly at plugs,
convenience receptacles, and the point where they exit from the apparatus.

11) Only use attachments/accessories specied by the manufacturer.

12) Use only with the cart, stand, tripod, bracket, or table specied by the

manufacturer, or sold with the apparatus. When a cart is used,
use caution when moving the cart/apparatus combination to
avoid injury from tip-over.

13) Unplug this apparatus during lightning storms or when unused for long

periods of time.

14) Refer all servicing to qualied service personnel. Servicing is required when

the apparatus has been damaged in any way, such as power-supply cord or plug
is damaged, liquid has been spilled or objects have fallen into the apparatus, the
apparatus has been exposed to rain or moisture, does not operate normally, or has
been dropped.

6

3. FEATURES

• 1/3 960H SONY EXview HAD CCD II

• High Resolution of 700TV Lines

• OSD Function

• Multi Language

(ENGLISH, CHINESE, RUSSIAN, SPANISH, GERMAN, FRENCH, PORTUGUESE, JAPANESE)

• 2DNR

• Privacy Zone / Motion Detect

• DC12V / AC24V Dual Voltage

• ATR(Adaptive Tone-curve Reproduction / Digital WDR)

The function provides gradation compensation to improve the contrast of subjects both
low-luminance areas and high luminance areas exist in the same picture

4. COMPONENTS

SUPER NIGHT VISION CAMERA

VIDEO OUTPUT

TEST CABLE

L-WRENCH / SCREW - 4ea

OPERATION MANUAL

7

5. NAME AND FUNCTION

①

②

①

Sunshield

②

Cable Concealed

Thru Bracket

③

LED : 10ea

④

Photo cell

⑤

Body

③ ④ ⑤

• CONTROL FUNCTION / SERVICE VIDEO CONNECTOR

• CONTROL FUNCTION

(OSD JOYSTICK)

LEFT

MENU

UP

RIGHT

DOWN

HANDHELD MONITOR

• SERVICE VIDEO CONNECTOR

8

5. NAME AND FUNCTION

• Heater

Heater

Built in heater protects the camera from low temperature.

(Operating temperature with Heater:-40℃)

• External Zoom & Focus Adjustable

External Zoom & Focus Adjustable

9

6. INSTALLATION

• MOUNTING POSITION

90˚TLIT

90˚TLIT

360˚PAN

360˚PAN

10

6. INSTALLATION

• MONITOR CONNECTION

DUAL(DC12V/AC24V)

DC12V/AC24V

DC12V/AC24V

BNC FEMALE

DC 12V POWER SUPPLY or
AC 24V POWER SUPPLY

VIDEO IN MONITOR

DC 12V POWER SUPPLY or
AC 24V POWER SUPPLY

VIDEO IN

MONITOR

DC12V

When you install the camera, please glue up the
end of cable to keep it stable in order to protect the
camera from the humidity problems.

DC12V

BNC FEMALE

DC12V

BNC FEMALE

11

RS485

DC 12V POWER SUPPLY

VIDEO IN

MONITOR

DC 12V POWER SUPPLY

VIDEO IN

MONITOR

RS485

7. DIMENSIONS

Unit : mm

10 POWER LED

Photo

cell

98.6

140

83.0

89.5

126.0

M12XP1.25

(256.5)

12

Ø95

(2EA)

106.5

10

135

125

8. SPECIFICATION

Signal Format NTSC PAL
Image Device 1/3˝ 960H SONY EXview HAD CCD II
Scanning System 2 : 1 Interlace
Scanning Frequency 15.734KHz(H), 59.94Hz(V) 15.625KHz(H), 50Hz(V)
Total Pixels 1020(H) X 508(V) 1020(H) X 596(V)
Effective Pixels 976(H) X 494(V) 976(H) X 582(V)
Electronic Shutter Speed 1/60 sec 1/50 sec
H.Resolution 750TV Lines
S/N Ratio More than 50dB (AGC OFF)
Min.Illumination LED On : 0 Lux
Sync System Internal
Gamma r= 0.45
Video Output Level 1.0 Vp-p Composite(75Ω)
OSD Built in (Joystick)
BLC OFF / BLC / HLC
2DNR OFF / ON (Level adjustable)
ATR OFF / ON (Level adjustable)
SMART IR On / Off
White Balance ATW / PUSH / MANUAL / PUSH-LOCK
Privacy Masking 4 Zones
Motion Detection 4 Zones
Day & Night(ICR) AUTO / Color / BW

Language
IP Rating IP67 (Water proof)

IR LED HI POWER LED, 10EA
IR LED Distance Up to 70M
Operating Temperature 14°F~122°F(-10°C~+50°C) / Heater On: -40°F~122°F(-40°C~+50°C)
Storage Temperature -4°F~140°F(-20°C~+60°C)
Humidity Less than 80%

Power Consumption

Lens Verifocal Auto Iris & DN Lens
Dimension 98.6(W) x 83(H) x 126(D)
Weight Approx.1.37Kg
Option RS-485, Heater

Specications and designs are subject to change for improving the functionality of this product without notice.

ENGLISH, CHINESE, RUSSIAN, SPANISH, GERMAN, FRENCH,

PORTUGUESE, JAPANESE

DC12V (±10%) Max.800mA, 1.6A(Heater On)
DC12V (±10%) Max.850mA, 1.1A(Heater On)

AC24V (±10%) Max.10W, 21W(Heater On)

13

9. OSD MANUAL

GENERAL STRUCTURE

SETUP

>FOCUS ADJUST [┛]
EXPOSURE [┛]
WHITE BALANCE [┛]
BLC [┛]
DAY&NIGHT [┛]
IMAGE [┛]
SPECIAL [┛]
FACTORY DEFAULT
EXIT

FOCUS ADJUST

FOCUS VALUE: 28

>FOCUS WINDOW ON

RETURN

EXPOSURE

>BRIGHTNESS
SHUTTER
FLICKERLESS
AGC MAX
INITIAL
RETURN

> WB MODE ATW

RED CONTROL ---­ BLUE CONTROL ---­ PUSH AUTO ---­ INITIAL
RETURN

WHITE BALANCE

...

7

...

1/60

...

OFF

...

30dB

BLC

>ATR MODE ON
ATR LEVEL 4
BLC MODE ON
BLC ZONE CENTER
BLC LEVEL 8
INITIAL
RETURN

DAY & NIGHT

>D&N MODE AUTO

DWELL TIME 3SEC
D -> N LEVEL 1
N -> D LEVEL 3
BURST OFF
IR OPTIMIZER ON
IR OPT.LEVEL 8
LED CONTROL MANUAL
LED LEVEL 15
INITIAL
RETURN

14

9. OSD MANUAL

IMAGE

>MIRROR OFF
DNR ON
DNR LEVEL 4
SHARPNESS 8
INITIAL
RETURN

SPECIAL

>CAM TITLE [┛]
LANGUAGE ENGLISH
COMM ADJUST [┛]
PRIVACY [┛]
MOTION DETECT [┛]
DISPLAY [┛]
DEFECT
INITIAL
RETURN

CAM TITLE

0123456789ABCDEFGHIJK
LMNOPQRSTUVWXYZ!()<>
SPA

>> <<BAK

TITLE SET
LOCATION [┛]

RETURN

COMM ADJUST

> CAM ID 1
BAUDRATE 9600
RETURN

PRIVACY

MOTION DETECT

0
ON

0

>ZONE NO
MASK MODE
V START 7
V END 12
H START 10
H END 19
COLOR 1
TRANSPARENCY 0%
MOSAIC OFF
INITIAL
RETURN

>ZONE NO
MOTION MODE ON
LEVEL 4
V START 7
V END 12
H START 10
H END 19
INITIAL
RETURN

DISPLAY

> CAM ID
CAM TITLE
MOTION DETECT ON
INITIAL
RETURN

DEFECT

> COMPENSATION ON
DETECTION (

RETURN

↓

ON
ON

)

[TITLE LOCATION]

TITLE

[U] [D] [L] [R] [M] <

15

9. OSD MANUAL

MAIN MENU Sub Menu Sub MENU

SETUP
FOCUS ADJUST

EXPOSURE

WHITE BALANCE

BLC

DAY&NIGHT

IMAGE

FOCUS WINDOW
RETURN
BRIGHTNESS 0~15
SHUTTER
FLICKERLESS
AGC MAX 6dB, 9dB, 12dB, 15dB, 18dB, 21dB, 24dB, 27dB, 30dB, 33dB, 36dB, 39dB, 42dB
INITIAL
RETURN
WB MODE
RED CONTROL
BLUE CONTROL
PUSH AUTO
INITIAL
RETURN
ATR MODE
ATR LEVEL
BLC MODE
BLC ZONE
BLC LEVEL
INITIAL
RETURN
D&N MODE
DWELL TIME
D -> N LEVEL
N -> D LEVEL
BURST
IR OPTIMIZER
IR OPT.LEVEL
LED CONTROL
LED LEVEL
INITIAL
RETURN
MIRROR
DNR
DNR LEVEL
SHARPNESS
INITIAL
RETURN

SPECIAL CAM TITLE

OFF, ON

1/60(50), 1/120(100),1/250, 1/500, 1/1k, 1/2k, 1/4k, 1/6k, 1/10k, 1/50k, 1/100k
OFF, ON

ATW, PUSH, PUSH LOCK, MANUAL
0 ~ 255
0 ~ 255

-

OFF, ON
0 ~ 4
OFF, ON, HLC
TOP, BOTTOM, CENTER, LEFT, BIGHT
0 ~ 15

COLOR, B/W, AUTO
0 ~ 10
0 ~ 19
1 ~ 20
OFF, ON
OFF, ON
0 ~ 15
MANUAL, AUTO
0 ~ 15

OFF, ON
OFF, ON
0 ~ 15
0 ~ 15

CAM TITLE

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K
L M O P Q R S T U V W Y Z ! - () <>
SPA>> <<BAK
LOCATION
RETURN

16

9. OSD MANUAL

MAIN MENU Sub Menu Sub MENU

LANGUAGE

COMM ADJUST

PRIVACY

SPECIAL

MOTION DETECT

DISPLAY

DEFECT

INITIAL

FACTORY DEFAULT
EXIT

RETURN

ENGLISH, CHINESE, RUSSIAN, SPANISH, GERMAN, FRENCH, PORTUGUESE, JAPANESE
CAM ID 1 ~ 255
BAUDRATE 2400, 4800, 9600, 19200
RETURN
ZONE NO 0 ~ 3
MASK MODE OFF, ON
V START 0 ~ 17
V END 1 ~ 18
H START 0 ~ 29
H END 1 ~ 30
COLOR 0 ~ 7
TRANSPARENCY 0%, 25%, 50%
MOSAIC OFF, ON
INITIAL
RETURN
ZONE NO 0 ~ 3
MOTION MODE OFF, ON
LEVEL 0 ~ 15
V START 0 ~ 6
V END 1 ~ 7
H START 0 ~ 10
H END 1 ~ 11
INITIAL
RETURN
CAM ID OFF, ON
CAM TITLE OFF, ON
MOTION DETECT OFF, ON
INITIAL
RETURN
COMPENSATION OFF, ON
DETECTION
RETURN

17

9. OSD MANUAL

OSD FUNCTION DESCRIPTION

1. FOCUS ADJUST

: According to the brightness of light to minimize the depth of focus, to be more accurate to focus.

- FOCUS VALUE: The higher the number, the focus will be a good t.

- FOCUS WINDOW: AF detector frame display ON/OFF.

FOCUS ADJUST
FOCUS VALUE: 28

>FOCUS WINDOW ON

RETURN

2. EXPOSURE

: Enable user to set up the function of BRIGHTNESS, SHUTTER, FLICKERLESS, AGC MAX.
Set up using LEFT, RIGHT KEY at each menu.

EXPOSURE

>BRIGHTNESS 7

SHUTTER 1/60
FLICKERLESS OFF
AGC MAX 30dB
INTIAL
RETURN

- BRIGHTNESS
: Enable user to control the image brightness (0~15steps).

- SHUTTER

: Enable user to set up the Shutter Speed.

-> 1/60(50), 1/100(120), 1/250, 1/500, 1/1K, 1/2K, 1/4K, 1/6K, 1/10K, 1/50K, 1/100K.
*() is for PAL TYPE.

- FLICKERLESS
: Enable user to set up the FLICKERLESS ON / OFF.

- AGC MAX
: Enable user to make imager bright to amplify the Gain.

-> 6dB ~ 42dB

- INITIAL
: Enable user to initialize the Exposure menu set up.

18

9. OSD MANUAL

3. WHITE BALANCE

: Enable user to represent the accurate white color by controlling the R,G,B level.
Setting up LEFT, RIGHT KEY on each menu.

- WB MODE

①

ATW : Enable user to trace the White Balance

automatically in the range of 2,300K~10,000K.

②

PUSH : Enable user to search for White Balance
automatically. In this mode, color temperature range is
broader than ATW.

③

PUSH LOCK : Enable user to x the White Balance

according to the color temperature in the certain
environment.

④

MANUAL : Enable user to sets the White Balance
according to the circumstance.

- RED CONTROL

: In the MANUAL setting of WB MODE, enable user to set the RED GAIN.

- BLUE CONTROL

: In the MANUAL setting of WB MODE, enable user to set the BLUE GAIN.

- PUSH AUTO

: In the PUSH LOCK setting of WB MODE, enable user to x the White Balance in

camera setting.

- INITIAL

: Enable user to reset the WHITE BALANCE menu setting..

4. BLC

: Use the condition which Image doesn’t gure out with BLC such as place surrounded windows

and lobby. Set the BLC using the LEFT, RIGHT KEY on the each menu.

- ATR MODE

: In this mode, the brightness of a single image is
compensated using the gamma curve.

- ATR LEVEL

: Enable user to set ATR Level(0~4 level).

- BLC(Back Light Compensation)

①

OFF : BLC mode off.

②

ON : BLC mode on.

③

HLC : High Light Compensation Mode on.

*High Light Compensation (HLC)

license plates and other such objects by suppressing or masking strong light sources (such as
the headlights of automobiles).

is a function that improves the visual recognition of

19

WHITE BALANCE

>WB MODE AUTO

RED CONTROL - - ­BLUE CONTROL - - ­PUSH AUTO - - ­INTIAL
RETURN

BLC

>ATR MODE ON

ATR LEVEL 4
BLC MODE ON
BLC ZONE CENTER
BLC LEVEL 8
INTIAL
RETURN

9. OSD MANUAL

- BLC ZONE :

-> TOP, BOTTOM, CENTER, LEFT, RIGHT.

- BLC LEVEL :

area(0~15 level).

- INITIAL :

5. DAY&NIGHT

: Conversion of output image COLOR / BW depending on exterior environment
Enable user to set the LEFT, RIGHT KEY in menu.

- D&N MODE

①
②
③

Enable user to convert to COLOR/BW automatically.

- DWELL TIME :

set to delay time for changing COLOR/BW(0~10sec).

- D->N LEVEL

: Day(Color) to Night(BW) a Sensor level(0~19).

- N->D LEVEL

: Night(BW) to Day(Color) a Sensor level(1~20).

- BURST

: In BW mode, Color burst signal ON / OFF.

- IR OPTIMIZER

: By the IR LED light, the screen is saturated, and automatically adjust the brightness,
so you can see the screen.

- IR OPT. LEVEL

: Enable user to control the Level (0~15steps).

- LED CONTROL

①
②

- LED LEVEL

: Enable user to control the IR-LED Level (0~15steps).

- INITIAL

: Enable user to initialize the setting in DAY&NIGHT menu.

Enable user to set the BLC area

Enable user to set BLC in selected

Enable user to initialize the BLC setting.

COLOR : Enable user to t the output image in color.
B/W : Enable user to t the output image in B/W.

AUTO :

In D&N MODE AUTO, enable user to

MANUAL : IR LED brightness is adjusted manually.
AUTO : IR LED brightness is adjusted automatically.

TOP

LEFT CENTER RIGHT

BOTTOM

DAT&NIGHT

>DAY&MODE AUTO

DWELL TIME 3SEC
D -> N LEVEL 1
N -> D LEVEL 3
BURST OFF
IR OPTIMIZER ON
IR OPT.LEVEL 8
LED CONTROL MANUAL
LED LEVEL 15
INTIAL
RETURN

20

9. OSD MANUAL

6. IMAGE

: MIRROR, DNR, SHARPNESS functions set up by pressing LEFT, RIGHT KEY.

IMAGE

>MIRROR OFF

DNR ON
DNR LEVEL 4
SHARPNESS 8
INITAL
RETURN

(OFF) (ON)

- MIRROR:

- DNR :

Enable user to reverse the image.

This function reduces noise by undertaking spatial ltering for one image.

(Outline of DNR function)

- DNR LEVEL :

- SHARPNESS :

- INITIAL :

7. SPECIAL

etting up the CAM TITLE, LANGUAGE, COMM ADJUST, PRIVACY, MOTION DETECT,

: S

DISPLAY, DEFECT. Set up using LEFT and RIGHT key in each menu.

Enable user to set level(0~15 steps).

Enable user to control the image sharpness (0~15steps).

Enable user to initialize the setting on IMAGE menu.

SPECIAL

>CAM TITLE

LANGUAGE ENGLISH
COMM ADJUST
PRIVACY
MOTION DETECT
DISPLAY
DEFECT
INITAL
RETURN

[┛]

[┛]
[┛]
[┛]
[┛]
[┛]

21

9. OSD MANUAL

- CAM TITLE :

①

A letter Choice from the screen using menu key.

②

Enable user to move to next menu using LEFT, RIGHT KEY in LOCATION.

③

By using UP, DOWN, LEFT, RIGHT KEY, enable user to choose any letters in
LOCATION and then get back to previous step.

④

Enable user to nish words choice and position by using LEFT, RIGHT KEY in RETURN.

- LANGUAGE :

ENGLISH, CHINESE, RUSSIAN, SPANISH, GERMAN, FRENCH, PORTUGUESE, JAPANESE.

->

- COMM ADJUST :

Enable user to set up CAMERA ID, BAUDRATE.

①

CAM ID : Enable user to set up Camera ID (1~255).

②

BAUDRATE : A communication speed to Communicate

with external device. (2400, 4800, 9600, 19200).

- PRIVACY :

(Maximum 4 point covered).

①

ZONE : Enable user to set up a position from 0 to 3 area.

②

MASK : Enable user to set up screen output of chosen position.

③

V START : Mask Vertical start position.

④

V END : Mask Vertical end position.

⑤

H START : Mask Horizontal start position.

⑥

H END : Mask Horizontal end position.

⑦

COLOR : Set the mask color.

⑧

TRANSPARENCY : Set the transparency of the mask.

⑨

MOSAIC : Mosaic is set to mask the effect.

⑩

INITIAL : Enable user to initialize setting of

PRIVACY MENU.

Enable user to choose any word in screen(Maximum 10 letter is available)

CAM TITLE

0123456789ABCDEFGHIJK
LMNOPQRSTUVWXYZ!-()<>
SPA>> <<BAK

TITLE SET
LOCATION [┛]

RETURN

[TITLE LOCATION]

TITLE SET

[U] [D] [L] [R] [M] <

Enable user to set up an OSD language

COMM ADJUST

>CAM ID

BAUDRATE 9600
RETURN

Privacy is the function that covers the some part on screen to prevent private life

PRIVACY

>ZONE NO 0

MASK MODE ON
V START 7
V END 12
H START 10
H END 19
COLOR 1
TRANSPARENCY 0%
MOSAIC OFF
INITIAL
RETURN

1

22

9. OSD MANUAL

- MOTION DETECT : Motion detection function.

①

MOTION MODE : Enable user to set up ON/OFF

②

LEVEL : Enable user to setup a motion detect sensitivity (0~3)

③

V START : Motion area Vertical start position.

④

V END : Motion area Vertical end position.

⑤

H START : Motion area Horizontal start position.

⑥

H END : Motion area Horizontal end position.

⑦

INITIAL : Enable user to initialize setting of

MOTION DETECT.

MOTION DETECT

>ZONE NO 0
MOTION MODE ON
LEVEL 4
V START 7
V END 12
H START 10
H END 19
INITIAL
RETURN

- DISPLAY:

- DEFECT :

compensate up to 64 white pixels.

8. FACTORY DEFAULT

: Enable user to reset all of the status as the factory default Setting up using
LEFT, RIGHT KEY.

9. EXIT

: Enable user to EXIT the OSD menu Setting up using LEFT, RIGHT KEY.

Enable user to set up a screen marking of CAM ID, CAM TITLE, MOTION DETECT.

①

CAM ID:
Enable user to set up output on Camera ID screen

②

CAM TITLE :

Enable user to set up output in xed CAM TITLE

③

MOTION DETECT: Enable user to set up out put of

MOTION on the screen as MOTION DETECT ON setting.

④

INITIAL : Enable user to initialize of DISPLAY menu.

DISPLAY

CAM ID ON
CAM TITLE ON
MOTION DETECT ON
INITIAL
RETURN

The white pixel detection and compensation function can automatically detect and

①

COMPENSATION

②

DETECTION : White pixel detection..

DEFECT COMPENSATION On/Off..

:

DEFECT

>COMPENSATION ON
DETECTION ( ↓ )
RETURN

23

10. Communication Protocol

Pelco “D” Protocol Commands

• Most widely used Commands

- TELE = UP KEY

- WIDE = DOWN KEY

- NEAR = LEFT KEY

- FAR = RIGHT KEY

- MENU = MENU KEY

24

MEMO

MEMO

Mount Guide

4-ø6.0