M117-N701-001
HIGH PERFORMANCE
Super Night Vision Camera
OPERATION MANUAL
Thank you for choosing our high quality camera. Before attempting
to connect operate this unit,please read and follow these instructions.
M117-N701-001
HIGH PERFORMANCE
Super Night Vision Camera
OPERATION MANUAL
Thank you for choosing our high quality camera. Before attempting
to connect operate this unit,please read and follow these instructions.
CAUTION
These servicing instructions are for use by qualied service personnel only.
To reduce the risk of electric shock do not perform any servicing other than
that contained in the operating instructions unless you are qualied to do so.
In USA and Canada, Use Class 2 Power Supply Only
2
CONTENTS
1. CAUTIONS
2. IMPORTANT SAFETY INSTRUCTIONS
3. FEATURES
4. COMPONENTS
5. NAME AND FUNCTION
6. INSTALLATION
7. DIMENSIONS
8. SPECIFICATION
9. OSD MANUAL
10. COMMUNICATION PROTOCOL
3
1. CAUTIONS
This device complies with Part 15 of the FCC Rules.
Operation is subject to the following two conditions;
1. This device may not cause harmful interference.
2. This device must accept any interference received, including
interference that may cause undesired operation.
Note
This equipment has been tested and found to comply with the limits for a Class A digital
device, pursuant to part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference when the equipment is operated
in a commercial environment. This equipment generates, uses, and can radiate radio
frequency energy and, if not installed and used in accordance with the instruction
manual, may cause harmful interference to radio communications. Operation of this
equipment in a residential area is likely to cause harmful interference in which case the
user will be required to correct the interference at his own expense.”
WARNING
This is a class A product. In a domestic environment this product may cause radio
interference in which case the user may be required to take adequate measures.
Caution
Any changes or modications in construction of this device which are not expressly
approved by the party responsible for compliance could void the user’s authority to
operate the equipment.
1. A regulated DC12V 1A power supply is recommended for use with this camera
for the best picture and the most stable operation.
An unregulated power supply can cause damage to the camera.
When unregulated power supply is applied, product warranty will be
out of subject.
2. It is recommended that the camera is used with a monitor that has a CCTV quality
75 video impedance level.
If your monitor is switched to high impedance then please adjust accordingly.
3. Do not attempt to disassemble the camera to gain access to the internal componets.
Refer servicing to your dealer.
4. Never face the camera towards the sun or any bright or reective light, which may
cause smear on the picture and possible damage to the CCD.
5. Do not remove the serial sticker for the warranty service.
4
1. CAUTIONS
Correct Disposal of This Product
(Waste Electrical & Electronic Equipment)
(Applicable in the European Union and other European countries with
separate collection systems)
This marking shown on the product or its literature, indicate that it should not
be disposed with other household wastes at the end of its working life. To
prevent possible harm to the environment or human health from uncontrolled
waste disposal, please separate this from other types of wastes and recycle it
responsibly to promote the sustainable reuse of material resources.
This product should not be mixed with other commercial wastes purchased this
product, or their local government ofce, for details of where and how they can
take item for environmentally safe recycling.
Business users should contact their supplier and check the terms and
conditions of the purchase contract.
Household users should contact either the retailer where they for disposal.
5
2 . IMPORTANT SAFETY INSTRUCTION
1) Read these instructions.
2) Keep these instructions.
3) Heed all warnings.
4) Follow all instructions.
5) Do not use this apparatus near water.
6) Clean only with dry cloth.
7) Do not block any ventilation openings. Install in accordance
with the manufacturer’s instructions.
8) Do not install near any heat sources such as radiators, heat registers,
stoves, or other apparatus (including ampliers) that produce heat.
9) Do not defeat the safety purpose of the polarized or grounding-type plug. A
polarized plug has two blades with one wider than the other. A grounding type plug
has two blades and a third grounding prong. The wide blade or the third prong are
provided for your safety. If the provided plug does not t into your outlet, consult an
electrician for replacement of the obsolete outlet.
10) Protect the power cord from being walked on or pinched particularly at plugs,
convenience receptacles, and the point where they exit from the apparatus.
11) Only use attachments/accessories specied by the manufacturer.
12) Use only with the cart, stand, tripod, bracket, or table specied by the
manufacturer, or sold with the apparatus. When a cart is used,
use caution when moving the cart/apparatus combination to
avoid injury from tip-over.
13) Unplug this apparatus during lightning storms or when unused for long
periods of time.
14) Refer all servicing to qualied service personnel. Servicing is required when
the apparatus has been damaged in any way, such as power-supply cord or plug
is damaged, liquid has been spilled or objects have fallen into the apparatus, the
apparatus has been exposed to rain or moisture, does not operate normally, or has
been dropped.
6
3. FEATURES
• 1/3 960H SONY EXview HAD CCD II
• High Resolution of 700TV Lines
• OSD Function
• Multi Language
(ENGLISH, CHINESE, RUSSIAN, SPANISH, GERMAN, FRENCH, PORTUGUESE, JAPANESE)
• 2DNR
• Privacy Zone / Motion Detect
• Smart IR
• DC12V / AC24V Dual Voltage
• ATR(Adaptive Tone-curve Reproduction / Digital WDR)
The function provides gradation compensation to improve the contrast of subjects both
low-luminance areas and high luminance areas exist in the same picture
4. COMPONENTS
SUPER NIGHT VISION CAMERA
VIDEO OUTPUT
TEST CABLE
L-WRENCH / SCREW - 4ea
OPERATION MANUAL
7
5. NAME AND FUNCTION
① ②
③ ④ ⑤
• Service Video connector & OSD Joystick
①
Sunshield
②
Cable Concealed
Thru Bracket
③
LED : 45ea
④
Photo cell
⑤
Body
• CONTROL FUNCTION
(OSD JOYSTICK)
LEFT
UP
RIGHT
MENU
DOWN
8
5. NAME AND FUNCTION
• Heater
Heater
Built in heater protects the camera from low temperature.
(Operating temperature with Heater:-40℃)
• External Zoom & Focus Adjustable
External Zoom & Focus Adjustable
9
6. INSTALLATION
• MOUNTING POSITION
90˚TLIT
360˚PAN
90˚TLIT
360˚PAN
10
6. INSTALLATION
• MONITOR CONNECTION
DC12V/AC24V
DC12V/AC24V
BNC FEMALE
DC 12V POWER SUPPLY or
AC 24V POWER SUPPLY
VIDEO IN
MONITOR
DC 12V POWER SUPPLY or
AC 24V POWER SUPPLY
VIDEO IN
MONITOR
RS485
When you install the camera, please glue up the end of cable to
keep it stable in order to protect the camera from the humidity problems.
11
7. DIMENSIONS
Unit : mm
45 LED
SENSOR
140
Ø80.6
83
110.6
M12XP1.25
243.3
10
(2EA)
135
125
106.5
Ø95
12
8. SPECIFICATION
Signal Format NTSC PAL
Image Device 1/3˝ 960H SONY EXview HAD CCD II
Scanning System 2 : 1 Interlace
Scanning Frequency 15.734KHz(H), 59.94Hz(V) 15.625KHz(H), 50Hz(V)
Total Pixels 1020(H) X 508(V) 1020(H) X 596(V)
Effective Pixels 976(H) X 494(V) 976(H) X 582(V)
Electronic Shutter Speed 1/60 sec 1/50 sec
H.Resolution 750TV Lines
S/N Ratio More than 50dB(AGC OFF)
Min.Illumination LED On : 0 Lux
Sync System Internal
Gamma r= 0.45
Video Output Level 1.0 Vp-p Composite(75Ω)
OSD Built in (Joystick)
BLC OFF / BLC / HLC
2DNR OFF/ON(Level adjustable)
ATR OFF/ON(Level adjustable)
SMART IR On / Off
White Balance ATW / PUSH / MANUAL / PUSH-LOCK
Privacy Masking 4 Zones
Motion Detection 4 Zones
Day & Night(ICR) AUTO / Color / BW
Language
IP Rating IP67 (Water proof)
IR LED 850nm, 45ea
IR LED Distance Up to 50M
Operating Temperature 14°F~122°F(-10°C~+50°C) / Heater On: -40°F~122°F(-40°C~+50°C)
Storage Temperature -4°F~140°F(-20°C~+60°C)
Humidity Less than 80%
Power Consumption
Lens Varifocal Lens
Dimension 98.6(W) x 83(H) x 110.6(D)
Weight Approx. 900g
Option RS-485, Heater
Specications and designs are subject to change for improving the functionality of this product without notice.
ENGLISH, CHINESE, RUSSIAN, SPANISH, GERMAN, FRENCH,
PORTUGUESE, JAPANESE
DC12V (±10%) Max.850mA, 1.1A(Heater On)
AC24V (±10%) Max.10W, 21W(Heater On)
13
9. OSD MANUAL
GENERAL STRUCTURE
SETUP
>FOCUS ADJUST [-]
EXPOSURE [-]
WHITE BALANCE [-]
BLC [-]
DAY&NIGHT [-]
IMAGE [-]
SPECIAL [-]
FACTORY DEFAULT
EXIT
FOCUS ADJUST
> RETURN
EXPOSURE
>BRIGHTNESS
SHUTTER
FLICKERLESS
AGC MAX
INITIAL
RETURN
> WB MODE AUTO
RED CONTROL --- BLUE CONTROL --- PUSH AUTO --- INITIAL
RETURN
WHITE BALANCE
...
...
...
...
BLC
>ATR MODE ON
ATR LEVEL 4
BLC MODE ON
BLC ZONE CENTER
BLC LEVEL 8
INITIAL
RETURN
DAY & NIGHT
>D&N MODE AUTO
DWELL TIME 3SEC
D -> N LEVEL 1
N -> D LEVEL 3
BURST OFF
SMART-IR ON
SMART-IR LEVEL 8
LED CONTROL MANUAL
LED LEVEL 20
INITIAL
RETURN
7
1/60
OFF
32dB
14
9. OSD MANUAL
IMAGE
>MIRROR OFF
DNR ON
DNR LEVEL 4
SHARPNESS 8
INITIAL
RETURN
SPECIAL
>CAM TITLE [-]
LANGUAGE ENGLISH
COMM ADJUST [-]
PRIVACY [-]
MOTION DETECT [-]
DISPLAY [-]
DEFECT
INITIAL
RETURN
CAM TITLE
0123456789ABCDEFGHIJK
LMNOPQRSTUVWXYZ!()<>
SPA
>> <<BAK
TITLE SET
LOCATION [┛]
RETURN
COMM ADJUST
> CAM ID 1
BAUDRATE 9600
RETURN
PRIVACY
MOTION DETECT
>ZONE NO
MASK MODE
V START 7
V END 12
H START 10
H END 19
COLOR 1
TRANSPARENCY 0%
MOSAIC OFF
INITIAL
RETURN
>ZONE NO
MOTION MODE ON
LEVEL 4
V START 7
V END 12
H START 10
H END 19
INITIAL
RETURN
DISPLAY
> CAM ID
CAM TITLE
MOTION DETECT ON
INITIAL
RETURN
DEFECT
> COMPENSATION ON
DETECTION (
RETURN
0
ON
0
ON
ON
)
↑
[TITLE LOCATION]
TITLE
[U] [D] [L] [R] [M] <
15
9. OSD MANUAL
MAIN MENU Sub Menu Sub MENU
SETUP
FOCUS ADJUST RETURN
EXPOSURE
WHITE BALANCE
BLC
DAY&NIGHT
IMAGE
SPECIAL CAM TITLE
BRIGHTNESS 0~15
SHUTTER
FLICKERLESS
AGC MAX 6dB, 9dB, 12dB, 15dB, 18dB, 21dB, 24dB, 27dB, 30dB, 33dB, 36dB, 39dB, 42dB
INITIAL
RETURN
WB MODE
RED CONTROL
BLUE CONTROL
PUSH AUTO
INITIAL
RETURN
ATR MODE
ATR LEVEL
BLC MODE
BLC ZONE
BLC LEVEL
INITIAL
RETURN
D&N MODE
DWELL TIME
D -> N LEVEL
N -> D LEVEL
BURST
SAMRT-IR
SMART-IR LEVEL
LED CONTROL
LED LEVEL
INITIAL
RETURN
MIRROR
DNR
DNR LEVEL
SHARPNESS
INITIAL
RETURN
1/60(50), 1/120(100),1/250, 1/500, 1/1k, 1/2k, 1/4k, 1/6k, 1/10k, 1/50k, 1/100k
OFF, ON
ATW, PUSH, PUSH LOCK, MANUAL
0 ~ 255
0 ~ 255
-
OFF, ON
0 ~ 4
OFF, ON, HLC
TOP, BOTTOM, CENTER, LEFT, BIGHT
0 ~ 15
COLOR, B/W, AUTO
0 ~ 10
0 ~ 19
1 ~ 20
OFF, ON
OFF, ON
0 ~ 15
MANUAL, AUTO
0 ~ 20
OFF, ON
OFF, ON
0 ~ 15
0 ~ 15
CAM TITLE
0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K
L M O P Q R S T U V W Y Z ! - () <>
SPA>> <<BAK
LOCATION
RETURN
16
9. OSD MANUAL
MAIN MENU Sub Menu Sub MENU
LANGUAGE
COMM ADJUST
PRIVACY
SPECIAL
MOTION DETECT
DISPLAY
DEFECT
INITIAL
FECTORY DEFAULT
EXT
RETURN
ENGLISH, CHINESE, RUSSIAN, SPANISH, GERMAN, FRENCH, PORTUGUESE, JAPANESE
CAM ID 0 ~ 255
BAUDRATE 2400, 4800, 9600, 19200
RETURN
ZONE NO 0 ~ 3
MASK MODE OFF, ON
V START 0 ~ 17
V END 1 ~ 18
H START 0 ~ 29
H END 1 ~ 30
COLOR 0 ~ 7
TRANSPARENCY 0%, 25%, 50%
MOSAIC OFF, ON
INITIAL
RETURN
ZONE NO 0 ~ 3
MOTION MODE OFF, ON
LEVEL 0 ~ 15
V START 0 ~ 6
V END 1 ~ 7
H START 0 ~ 10
H END 1 ~ 11
INITIAL
RETURN
CAM ID OFF, ON
CAM TITLE OFF, ON
MOTION DETECT OFF, ON
INITIAL
RETURN
COMPENSATION OFF, ON
DETECTION
RETURN
17
9. OSD MANUAL
OSD FUNCTION DESCRIPTION
1. FOCUS ADJUST
: According to the brightness of light to minimize the depth of focus, to be more accurate to focus.
FOCUS
>RETURN
2. EXPOSURE
: Enable user to set up the function of BRIGHTNESS, SHUTTER, FLICKERLESS, AGC.
Set up using LEFT, RIGHT KEY at each menu.
EXPOSURE
>BRIGHTNESS 7
SHUTTER 1/60
FLICKERLESS OFF
AGC MAX 30dB
INTIAL
RETURN
- BRIGHTNESS
: Enable user to control the image brightness (0~15steps).
- SHUTTER
: Enable user to set up the Shutter Speed.
-> 1/60(50), 1/100(120), 1/250, 1/500, 1/1K, 1/2K, 1/4K, 1/6K, 1/10K, 1/50K, 1/100K.
*() is for PAL TYPE.
- FLICKERLESS
: Enable user to set up the FLICKERLESS ON/OFF.
- AGC MAX
: Enable user to make imager bright to amplify the Gain.
-> 6dB~42dB
- INITIAL
: Enable user to initialize the Exposure menu set up.
18
9. OSD MANUAL
3. WHITE BALANCE
: Enable user to represent the accurate white color by controlling the R,G,B level. Setting up
LEFT, RIGHT KEY on each menu.
- WB MODE
①
ATW : Enable user to trace the White Balance
automatically in the range of 2,300K~10,000K.
②
PUSH : Enable user to search for White Balance
automatically. In this mode, color temperature range is
broader than ATW.
③
PUSH LOCK : Enable user to x the White Balance
according to the color temperature in the certain
environment.
④
MANUAL : Enable user to sets the White Balance
according to the circumstance.
- RED CONTROL
: In the MANUAL setting of WB MODE, enable user to set the RED GAIN.
- BLUE CONTROL
: In the MANUAL setting of WB MODE, enable user to set the BLUE GAIN.
- PUSH AUTO
: In the PUSH LOCK setting of WB MODE, enable user to x the White Balance in
camera setting.
- INITIAL
: Enable user to reset the WHITE BALANCE menu setting..
4. BLC
: Use the condition which Image doesn’t gure out with BLC such as place surrounded windows
and lobby. Set the BLC using the LEFT, RIGHT KEY on the each menu.
- ATR MODE
: In this mode, the brightness of a single image is
compensated using the gamma curve.
- ATR LEVEL
: Enable user to set ATR Level(0~4 level).
- BLC(Back Light Compensation)
①
OFF : BLC mode off.
②
ON : BLC mode on.
③
HLC : High Light Compensation Mode on.
*High Light Compensation (HLC)
license plates and other such objects by suppressing or masking strong light sources (such as
the headlights of automobiles).
is a function that improves the visual recognition of
19
WHITE BALANCE
>WB MODE AUTO
RED CONTROL - - BLUE CONTROL - - PUSH AUTO - - INTIAL
RETURN
BLC
>ATR MODE ON
ATR LEVEL 4
BLC MODE ON
BLC ZONE CENTER
BLC LEVEL 8
INTIAL
RETURN
9. OSD MANUAL
- BLC ZONE :
-> TOP, BOTTOM, CENTER, LEFT, RIGHT.
- BLC LEVEL :
area(0~15 level).
- INITIAL :
5. DAY&NIGHT
: Conversion of output image COLOR / BW depending on exterior environment
Enable user to set the LEFT, RIGHT KEY in menu.
- D&N MODE
①
②
③
Enable user to convert to COLOR/BW automatically.
- DWELL TIME :
set to delay time for changing COLOR/BW(0~10sec).
- D->N LEVEL
: Day(Color) to Night(BW) a Sensor level(0~19).
- N->D LEVEL
: Night(BW) to Day(Color) a Sensor level(1~20).
- BURST
: In BW mode, Color burst signal ON / OFF.
- SMART-IR
: By the IR LED light, the screen is saturated, and automatically adjust the brightness,
so you can see the screen.
- SMART-IR LEVEL
: Enable user to control the Level (0~15steps).
- LED CONTROL
①
②
- LED LEVEL
: Enable user to control the IR-LED Level (0~15steps).
- INITIAL
: Enable user to initialize the setting in DAY&NIGHT menu.
Enable user to set the BLC area
Enable user to set BLC in selected
Enable user to initialize the BLC setting.
COLOR : Enable user to t the output image in color.
B/W : Enable user to t the output image in B/W.
AUTO :
In D&N MODE AUTO, enable user to
MANUAL : IR LED brightness is adjusted manually.
AUTO : IR LED brightness is adjusted automatically.
TOP
LEFT CENTER RIGHT
BOTTOM
DAT&NIGHT
>DAY&MODE AUTO
DWELL TIME 3SEC
D -> N LEVEL 1
N -> D LEVEL 3
BURST OFF
SMART-IR ON
SMART-IR-LEVEL 8
LED CONTROL MANUAL
LED LEVEL 20
INTIAL
RETURN
20
9. OSD MANUAL
6. IMAGE
: MIRROR, DNR, SHARPNESS functions set up by pressing LEFT, RIGHT KEY.
IMAGE
>MIRROR OFF
DNR ON
DNR LEVEL 4
SHARPNESS 8
INITAL
RETURN
(OFF) (ON)
- MIRROR:
- DNR :
Enable user to reverse the image.
This function reduces noise by undertaking spatial ltering for one image.
(Outline of DNR function)
- DNR LEVEL :
- SHARPNESS :
- INITIAL :
7. SPECIAL
etting up the CAM TITLE, LANGUAGE, COMM ADJUST, PRIVACY, MOTION DETECT,
: S
DISPLAY, DEFECT. Set up using LEFT and RIGHT key in each menu.
Enable user to set level(0~15 steps).
Enable user to control the image sharpness (0~15steps).
Enable user to initialize the setting on IMAGE menu.
SPECIAL
>CAM TITLE
LANGUAGE ENGLISH
COMM ADJUST
PRIVACY
MOTION DETECT
DISPLAY
DEFECT
INITAL
RETURN
[┛]
[┛]
[┛]
[┛]
[┛]
[┛]
21
9. OSD MANUAL
- CAM TITLE :
①
A letter Choice from the screen using menu key
②
Enable user to move to next menu using LEFT, RIGHT KEY in LOCATION.
③
By using UP, DOWN, LEFT, RIGHT KEY, enable user to choose any letters in
LOCATION and then get back to previous step.
④
Enable user to nish words choice and position by using LEFT, RIGHT KEY in RETURN
- LANGUAGE :
ENGLISH, CHINESE, RUSSIAN, SPANISH, GERMAN, FRENCH, PORTUGUESE, JAPANESE.
->
- COMM ADJUST :
Enable user to set up CAMERA ID, BAUDRATE.
①
CAM ID : Enable user to set up Camera ID (0~255).
②
BAUDRATE : A communication speed to Communicate
with external device. (2400, 4800, 9600, 19200).
- PRIVACY :
some part on screen to prevent private life
(Maximum 4 point covered).
①
ZONE : Enable user to set up a position from 0 to 3 area.
②
MASK : Enable user to set up screen output of chosen position.
③
V START : Mask Vertical start position.
④
V END : Mask Vertical end position.
⑤
H START : Mask Horizontal start position.
⑥
H END : Mask Horizontal end position.
⑦
COLOR : Set the mask color.
⑧
TRANSPARENCY : Set the transparency of the mask.
⑨
MOSAIC : Mosaic is set to mask the effect.
⑩
INITIAL : Enable user to initialize setting of
PRIVACY MENU
Enable user to choose any word in screen(Maximum 10 letter is available)
CAM TITLE
0123456789ABCDEFGHIJK
LMNOPQRSTUVWXYZ!-()<>
SPA>> <<BAK
TITLE SET
LOCATION [┛]
RETURN
[TITLE LOCATION]
TITLE SET
[U] [D] [L] [R] [M] <
Enable user to set up an OSD language
COMM ADJUST
>CAM ID
Privacy is the function that covers the
BAUDRATE 9600
RETURN
PRIVACY
>ZONE NO 0
MASK MODE ON
V START 7
V END 12
H START 10
H END 19
COLOR 1
TRANSPARENCY 0%
MOSAIC OFF
INITIAL
RETURN
1
22
9. OSD MANUAL
- MOTION DETECT : Motion detection function.
①
MOTION MODE : Enable user to set up ON/OFF
②
LEVEL : Enable user to setup a motion detect sensitivity (0~3)
③
V START : Motion area Vertical start position.
④
V END : Motion area Vertical end position.
⑤
H START : Motion area Horizontal start position.
⑥
H END : Motion area Horizontal end position.
⑦
INITIAL : Enable user to initialize setting of
MOTION DETECT
MOTION DETECT
>ZONE NO 0
MOTION MODE ON
LEVEL 4
V START 7
V END 12
H START 10
H END 19
INITIAL
RETURN
- DISPLAY :
MOTION DETECT.
①
Enable user to set up output on Camera ID screen
②
Enable user to set up output in xed CAM TITLE
③
MOTION on the screen as MOTION DETECT ON setting.
④
- DEFECT :
compensate up to 64 white pixels.
①
②
8. FACTORY DEFAULT
: Enable user to reset all of the status as the factory default Setting up using
LEFT, RIGHT KEY
9. EXIT
: Enable user to EXIT the OSD menu Setting up using LEFT, RIGHT KEY
Enable user to set up a screen marking of CAM ID, CAM TITLE,
CAM ID :
CAM TITLE :
MOTION DETECT: Enable user to set up out put of
INITIAL : Enable user to initialize of DISPLAY menu.
DISPLAY
CAM ID ON
CAM TITLE ON
MOTION DETECT ON
INITIAL
RETURN
The white pixel detection and compensation function can automatically detect and
COMPENSATION
DETECTION : White pixel detection..
DEFECT COMPENSATION On/Off..
:
DEFECT
>COMPENSATION ON
DETECTION (↑)
RETURN
23
10. Communication Protocol
Pelco “D” Protocol Commands
• Most widely used Commands
- TELE = UP KEY
- WIDE = DOWN KEY
- NEAR = LEFT KEY
- FAR = RIGHT KEY
- MENU = MENU KEY
24
CAUTION
These servicing instructions are for use by qualied service personnel only.
To reduce the risk of electric shock do not perform any servicing other than
that contained in the operating instructions unless you are qualied to do so.
In USA and Canada, Use Class 2 Power Supply Only
2
CONTENTS
1. CAUTIONS
2. IMPORTANT SAFETY INSTRUCTIONS
3. FEATURES
4. COMPONENTS
5. NAME AND FUNCTION
6. INSTALLATION
7. DIMENSIONS
8. SPECIFICATION
9. OSD MANUAL
10. COMMUNICATION PROTOCOL
3
1. CAUTIONS
This device complies with Part 15 of the FCC Rules.
Operation is subject to the following two conditions;
1. This device may not cause harmful interference.
2. This device must accept any interference received, including
interference that may cause undesired operation.
Note
This equipment has been tested and found to comply with the limits for a Class A digital
device, pursuant to part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference when the equipment is operated
in a commercial environment. This equipment generates, uses, and can radiate radio
frequency energy and, if not installed and used in accordance with the instruction
manual, may cause harmful interference to radio communications. Operation of this
equipment in a residential area is likely to cause harmful interference in which case the
user will be required to correct the interference at his own expense.”
WARNING
This is a class A product. In a domestic environment this product may cause radio
interference in which case the user may be required to take adequate measures.
Caution
Any changes or modications in construction of this device which are not expressly
approved by the party responsible for compliance could void the user’s authority to
operate the equipment.
1. A regulated DC12V 1A power supply is recommended for use with this camera
for the best picture and the most stable operation.
An unregulated power supply can cause damage to the camera.
When unregulated power supply is applied, product warranty will be
out of subject.
2. It is recommended that the camera is used with a monitor that has a CCTV quality
75 video impedance level.
If your monitor is switched to high impedance then please adjust accordingly.
3. Do not attempt to disassemble the camera to gain access to the internal componets.
Refer servicing to your dealer.
4. Never face the camera towards the sun or any bright or reective light, which may
cause smear on the picture and possible damage to the CCD.
5. Do not remove the serial sticker for the warranty service.
4
1. CAUTIONS
Correct Disposal of This Product
(Waste Electrical & Electronic Equipment)
(Applicable in the European Union and other European countries with
separate collection systems)
This marking shown on the product or its literature, indicate that it should not
be disposed with other household wastes at the end of its working life. To
prevent possible harm to the environment or human health from uncontrolled
waste disposal, please separate this from other types of wastes and recycle it
responsibly to promote the sustainable reuse of material resources.
This product should not be mixed with other commercial wastes purchased this
product, or their local government ofce, for details of where and how they can
take item for environmentally safe recycling.
Business users should contact their supplier and check the terms and
conditions of the purchase contract.
Household users should contact either the retailer where they for disposal.
5
2 . IMPORTANT SAFETY INSTRUCTION
1) Read these instructions.
2) Keep these instructions.
3) Heed all warnings.
4) Follow all instructions.
5) Do not use this apparatus near water.
6) Clean only with dry cloth.
7) Do not block any ventilation openings. Install in accordance
with the manufacturer’s instructions.
8) Do not install near any heat sources such as radiators, heat registers,
stoves, or other apparatus (including ampliers) that produce heat.
9) Do not defeat the safety purpose of the polarized or grounding-type plug. A
polarized plug has two blades with one wider than the other. A grounding type plug
has two blades and a third grounding prong. The wide blade or the third prong are
provided for your safety. If the provided plug does not t into your outlet, consult an
electrician for replacement of the obsolete outlet.
10) Protect the power cord from being walked on or pinched particularly at plugs,
convenience receptacles, and the point where they exit from the apparatus.
11) Only use attachments/accessories specied by the manufacturer.
12) Use only with the cart, stand, tripod, bracket, or table specied by the
manufacturer, or sold with the apparatus. When a cart is used,
use caution when moving the cart/apparatus combination to
avoid injury from tip-over.
13) Unplug this apparatus during lightning storms or when unused for long
periods of time.
14) Refer all servicing to qualied service personnel. Servicing is required when
the apparatus has been damaged in any way, such as power-supply cord or plug
is damaged, liquid has been spilled or objects have fallen into the apparatus, the
apparatus has been exposed to rain or moisture, does not operate normally, or has
been dropped.
6
3. FEATURES
• 1/3 960H SONY EXview HAD CCD II
• High Resolution of 700TV Lines
• OSD Function
• Multi Language
(ENGLISH, CHINESE, RUSSIAN, SPANISH, GERMAN, FRENCH, PORTUGUESE, JAPANESE)
• 2DNR
• Privacy Zone / Motion Detect
• Smart IR
• DC12V / AC24V Dual Voltage
• ATR(Adaptive Tone-curve Reproduction / Digital WDR)
The function provides gradation compensation to improve the contrast of subjects both
low-luminance areas and high luminance areas exist in the same picture
4. COMPONENTS
SUPER NIGHT VISION CAMERA
VIDEO OUTPUT
TEST CABLE
L-WRENCH / SCREW - 4ea
OPERATION MANUAL
7
5. NAME AND FUNCTION
① ②
③ ④ ⑤
• Service Video connector & OSD Joystick
①
Sunshield
②
Cable Concealed
Thru Bracket
③
LED : 45ea
④
Photo cell
⑤
Body
• CONTROL FUNCTION
(OSD JOYSTICK)
LEFT
UP
RIGHT
MENU
DOWN
8
5. NAME AND FUNCTION
• Heater
Heater
Built in heater protects the camera from low temperature.
(Operating temperature with Heater:-40℃)
• External Zoom & Focus Adjustable
External Zoom & Focus Adjustable
9
6. INSTALLATION
• MOUNTING POSITION
90˚TLIT
360˚PAN
90˚TLIT
360˚PAN
10
6. INSTALLATION
• MONITOR CONNECTION
DC12V/AC24V
DC12V/AC24V
BNC FEMALE
DC 12V POWER SUPPLY or
AC 24V POWER SUPPLY
VIDEO IN
MONITOR
DC 12V POWER SUPPLY or
AC 24V POWER SUPPLY
VIDEO IN
MONITOR
RS485
When you install the camera, please glue up the end of cable to
keep it stable in order to protect the camera from the humidity problems.
11
7. DIMENSIONS
Unit : mm
45 LED
SENSOR
140
Ø80.6
83
110.6
M12XP1.25
243.3
10
(2EA)
135
125
106.5
Ø95
12
8. SPECIFICATION
Signal Format NTSC PAL
Image Device 1/3˝ 960H SONY EXview HAD CCD II
Scanning System 2 : 1 Interlace
Scanning Frequency 15.734KHz(H), 59.94Hz(V) 15.625KHz(H), 50Hz(V)
Total Pixels 1020(H) X 508(V) 1020(H) X 596(V)
Effective Pixels 976(H) X 494(V) 976(H) X 582(V)
Electronic Shutter Speed 1/60 sec 1/50 sec
H.Resolution 750TV Lines
S/N Ratio More than 50dB(AGC OFF)
Min.Illumination LED On : 0 Lux
Sync System Internal
Gamma r= 0.45
Video Output Level 1.0 Vp-p Composite(75Ω)
OSD Built in (Joystick)
BLC OFF / BLC / HLC
2DNR OFF/ON(Level adjustable)
ATR OFF/ON(Level adjustable)
SMART IR On / Off
White Balance ATW / PUSH / MANUAL / PUSH-LOCK
Privacy Masking 4 Zones
Motion Detection 4 Zones
Day & Night(ICR) AUTO / Color / BW
Language
IP Rating IP67 (Water proof)
IR LED 850nm, 45ea
IR LED Distance Up to 50M
Operating Temperature 14°F~122°F(-10°C~+50°C) / Heater On: -40°F~122°F(-40°C~+50°C)
Storage Temperature -4°F~140°F(-20°C~+60°C)
Humidity Less than 80%
Power Consumption
Lens Varifocal Lens
Dimension 98.6(W) x 83(H) x 110.6(D)
Weight Approx. 900g
Option RS-485, Heater
Specications and designs are subject to change for improving the functionality of this product without notice.
ENGLISH, CHINESE, RUSSIAN, SPANISH, GERMAN, FRENCH,
PORTUGUESE, JAPANESE
DC12V (±10%) Max.850mA, 1.1A(Heater On)
AC24V (±10%) Max.10W, 21W(Heater On)
13
9. OSD MANUAL
GENERAL STRUCTURE
SETUP
>FOCUS ADJUST [-]
EXPOSURE [-]
WHITE BALANCE [-]
BLC [-]
DAY&NIGHT [-]
IMAGE [-]
SPECIAL [-]
FACTORY DEFAULT
EXIT
FOCUS ADJUST
> RETURN
EXPOSURE
>BRIGHTNESS
SHUTTER
FLICKERLESS
AGC MAX
INITIAL
RETURN
> WB MODE AUTO
RED CONTROL --- BLUE CONTROL --- PUSH AUTO --- INITIAL
RETURN
WHITE BALANCE
...
...
...
...
BLC
>ATR MODE ON
ATR LEVEL 4
BLC MODE ON
BLC ZONE CENTER
BLC LEVEL 8
INITIAL
RETURN
DAY & NIGHT
>D&N MODE AUTO
DWELL TIME 3SEC
D -> N LEVEL 1
N -> D LEVEL 3
BURST OFF
SMART-IR ON
SMART-IR LEVEL 8
LED CONTROL MANUAL
LED LEVEL 20
INITIAL
RETURN
7
1/60
OFF
32dB
14
9. OSD MANUAL
IMAGE
>MIRROR OFF
DNR ON
DNR LEVEL 4
SHARPNESS 8
INITIAL
RETURN
SPECIAL
>CAM TITLE [-]
LANGUAGE ENGLISH
COMM ADJUST [-]
PRIVACY [-]
MOTION DETECT [-]
DISPLAY [-]
DEFECT
INITIAL
RETURN
CAM TITLE
0123456789ABCDEFGHIJK
LMNOPQRSTUVWXYZ!()<>
SPA
>> <<BAK
TITLE SET
LOCATION [┛]
RETURN
COMM ADJUST
> CAM ID 1
BAUDRATE 9600
RETURN
PRIVACY
MOTION DETECT
>ZONE NO
MASK MODE
V START 7
V END 12
H START 10
H END 19
COLOR 1
TRANSPARENCY 0%
MOSAIC OFF
INITIAL
RETURN
>ZONE NO
MOTION MODE ON
LEVEL 4
V START 7
V END 12
H START 10
H END 19
INITIAL
RETURN
DISPLAY
> CAM ID
CAM TITLE
MOTION DETECT ON
INITIAL
RETURN
DEFECT
> COMPENSATION ON
DETECTION (
RETURN
0
ON
0
ON
ON
)
↑
[TITLE LOCATION]
TITLE
[U] [D] [L] [R] [M] <
15
9. OSD MANUAL
MAIN MENU Sub Menu Sub MENU
SETUP
FOCUS ADJUST RETURN
EXPOSURE
WHITE BALANCE
BLC
DAY&NIGHT
IMAGE
SPECIAL CAM TITLE
BRIGHTNESS 0~15
SHUTTER
FLICKERLESS
AGC MAX 6dB, 9dB, 12dB, 15dB, 18dB, 21dB, 24dB, 27dB, 30dB, 33dB, 36dB, 39dB, 42dB
INITIAL
RETURN
WB MODE
RED CONTROL
BLUE CONTROL
PUSH AUTO
INITIAL
RETURN
ATR MODE
ATR LEVEL
BLC MODE
BLC ZONE
BLC LEVEL
INITIAL
RETURN
D&N MODE
DWELL TIME
D -> N LEVEL
N -> D LEVEL
BURST
SAMRT-IR
SMART-IR LEVEL
LED CONTROL
LED LEVEL
INITIAL
RETURN
MIRROR
DNR
DNR LEVEL
SHARPNESS
INITIAL
RETURN
1/60(50), 1/120(100),1/250, 1/500, 1/1k, 1/2k, 1/4k, 1/6k, 1/10k, 1/50k, 1/100k
OFF, ON
ATW, PUSH, PUSH LOCK, MANUAL
0 ~ 255
0 ~ 255
-
OFF, ON
0 ~ 4
OFF, ON, HLC
TOP, BOTTOM, CENTER, LEFT, BIGHT
0 ~ 15
COLOR, B/W, AUTO
0 ~ 10
0 ~ 19
1 ~ 20
OFF, ON
OFF, ON
0 ~ 15
MANUAL, AUTO
0 ~ 20
OFF, ON
OFF, ON
0 ~ 15
0 ~ 15
CAM TITLE
0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K
L M O P Q R S T U V W Y Z ! - () <>
SPA>> <<BAK
LOCATION
RETURN
16
9. OSD MANUAL
MAIN MENU Sub Menu Sub MENU
LANGUAGE
COMM ADJUST
PRIVACY
SPECIAL
MOTION DETECT
DISPLAY
DEFECT
INITIAL
FECTORY DEFAULT
EXT
RETURN
ENGLISH, CHINESE, RUSSIAN, SPANISH, GERMAN, FRENCH, PORTUGUESE, JAPANESE
CAM ID 0 ~ 255
BAUDRATE 2400, 4800, 9600, 19200
RETURN
ZONE NO 0 ~ 3
MASK MODE OFF, ON
V START 0 ~ 17
V END 1 ~ 18
H START 0 ~ 29
H END 1 ~ 30
COLOR 0 ~ 7
TRANSPARENCY 0%, 25%, 50%
MOSAIC OFF, ON
INITIAL
RETURN
ZONE NO 0 ~ 3
MOTION MODE OFF, ON
LEVEL 0 ~ 15
V START 0 ~ 6
V END 1 ~ 7
H START 0 ~ 10
H END 1 ~ 11
INITIAL
RETURN
CAM ID OFF, ON
CAM TITLE OFF, ON
MOTION DETECT OFF, ON
INITIAL
RETURN
COMPENSATION OFF, ON
DETECTION
RETURN
17
9. OSD MANUAL
OSD FUNCTION DESCRIPTION
1. FOCUS ADJUST
: According to the brightness of light to minimize the depth of focus, to be more accurate to focus.
FOCUS
>RETURN
2. EXPOSURE
: Enable user to set up the function of BRIGHTNESS, SHUTTER, FLICKERLESS, AGC.
Set up using LEFT, RIGHT KEY at each menu.
EXPOSURE
>BRIGHTNESS 7
SHUTTER 1/60
FLICKERLESS OFF
AGC MAX 30dB
INTIAL
RETURN
- BRIGHTNESS
: Enable user to control the image brightness (0~15steps).
- SHUTTER
: Enable user to set up the Shutter Speed.
-> 1/60(50), 1/100(120), 1/250, 1/500, 1/1K, 1/2K, 1/4K, 1/6K, 1/10K, 1/50K, 1/100K.
*() is for PAL TYPE.
- FLICKERLESS
: Enable user to set up the FLICKERLESS ON/OFF.
- AGC MAX
: Enable user to make imager bright to amplify the Gain.
-> 6dB~42dB
- INITIAL
: Enable user to initialize the Exposure menu set up.
18
9. OSD MANUAL
3. WHITE BALANCE
: Enable user to represent the accurate white color by controlling the R,G,B level. Setting up
LEFT, RIGHT KEY on each menu.
- WB MODE
①
ATW : Enable user to trace the White Balance
automatically in the range of 2,300K~10,000K.
②
PUSH : Enable user to search for White Balance
automatically. In this mode, color temperature range is
broader than ATW.
③
PUSH LOCK : Enable user to x the White Balance
according to the color temperature in the certain
environment.
④
MANUAL : Enable user to sets the White Balance
according to the circumstance.
- RED CONTROL
: In the MANUAL setting of WB MODE, enable user to set the RED GAIN.
- BLUE CONTROL
: In the MANUAL setting of WB MODE, enable user to set the BLUE GAIN.
- PUSH AUTO
: In the PUSH LOCK setting of WB MODE, enable user to x the White Balance in
camera setting.
- INITIAL
: Enable user to reset the WHITE BALANCE menu setting..
4. BLC
: Use the condition which Image doesn’t gure out with BLC such as place surrounded windows
and lobby. Set the BLC using the LEFT, RIGHT KEY on the each menu.
- ATR MODE
: In this mode, the brightness of a single image is
compensated using the gamma curve.
- ATR LEVEL
: Enable user to set ATR Level(0~4 level).
- BLC(Back Light Compensation)
①
OFF : BLC mode off.
②
ON : BLC mode on.
③
HLC : High Light Compensation Mode on.
*High Light Compensation (HLC)
license plates and other such objects by suppressing or masking strong light sources (such as
the headlights of automobiles).
is a function that improves the visual recognition of
19
WHITE BALANCE
>WB MODE AUTO
RED CONTROL - - BLUE CONTROL - - PUSH AUTO - - INTIAL
RETURN
BLC
>ATR MODE ON
ATR LEVEL 4
BLC MODE ON
BLC ZONE CENTER
BLC LEVEL 8
INTIAL
RETURN
9. OSD MANUAL
- BLC ZONE :
-> TOP, BOTTOM, CENTER, LEFT, RIGHT.
- BLC LEVEL :
area(0~15 level).
- INITIAL :
5. DAY&NIGHT
: Conversion of output image COLOR / BW depending on exterior environment
Enable user to set the LEFT, RIGHT KEY in menu.
- D&N MODE
①
②
③
Enable user to convert to COLOR/BW automatically.
- DWELL TIME :
set to delay time for changing COLOR/BW(0~10sec).
- D->N LEVEL
: Day(Color) to Night(BW) a Sensor level(0~19).
- N->D LEVEL
: Night(BW) to Day(Color) a Sensor level(1~20).
- BURST
: In BW mode, Color burst signal ON / OFF.
- SMART-IR
: By the IR LED light, the screen is saturated, and automatically adjust the brightness,
so you can see the screen.
- SMART-IR LEVEL
: Enable user to control the Level (0~15steps).
- LED CONTROL
①
②
- LED LEVEL
: Enable user to control the IR-LED Level (0~15steps).
- INITIAL
: Enable user to initialize the setting in DAY&NIGHT menu.
Enable user to set the BLC area
Enable user to set BLC in selected
Enable user to initialize the BLC setting.
COLOR : Enable user to t the output image in color.
B/W : Enable user to t the output image in B/W.
AUTO :
In D&N MODE AUTO, enable user to
MANUAL : IR LED brightness is adjusted manually.
AUTO : IR LED brightness is adjusted automatically.
TOP
LEFT CENTER RIGHT
BOTTOM
DAT&NIGHT
>DAY&MODE AUTO
DWELL TIME 3SEC
D -> N LEVEL 1
N -> D LEVEL 3
BURST OFF
SMART-IR ON
SMART-IR-LEVEL 8
LED CONTROL MANUAL
LED LEVEL 20
INTIAL
RETURN
20
9. OSD MANUAL
6. IMAGE
: MIRROR, DNR, SHARPNESS functions set up by pressing LEFT, RIGHT KEY.
IMAGE
>MIRROR OFF
DNR ON
DNR LEVEL 4
SHARPNESS 8
INITAL
RETURN
(OFF) (ON)
- MIRROR:
- DNR :
Enable user to reverse the image.
This function reduces noise by undertaking spatial ltering for one image.
(Outline of DNR function)
- DNR LEVEL :
- SHARPNESS :
- INITIAL :
7. SPECIAL
etting up the CAM TITLE, LANGUAGE, COMM ADJUST, PRIVACY, MOTION DETECT,
: S
DISPLAY, DEFECT. Set up using LEFT and RIGHT key in each menu.
Enable user to set level(0~15 steps).
Enable user to control the image sharpness (0~15steps).
Enable user to initialize the setting on IMAGE menu.
SPECIAL
>CAM TITLE
LANGUAGE ENGLISH
COMM ADJUST
PRIVACY
MOTION DETECT
DISPLAY
DEFECT
INITAL
RETURN
[┛]
[┛]
[┛]
[┛]
[┛]
[┛]
21
9. OSD MANUAL
- CAM TITLE :
①
A letter Choice from the screen using menu key
②
Enable user to move to next menu using LEFT, RIGHT KEY in LOCATION.
③
By using UP, DOWN, LEFT, RIGHT KEY, enable user to choose any letters in
LOCATION and then get back to previous step.
④
Enable user to nish words choice and position by using LEFT, RIGHT KEY in RETURN
- LANGUAGE :
ENGLISH, CHINESE, RUSSIAN, SPANISH, GERMAN, FRENCH, PORTUGUESE, JAPANESE.
->
- COMM ADJUST :
Enable user to set up CAMERA ID, BAUDRATE.
①
CAM ID : Enable user to set up Camera ID (0~255).
②
BAUDRATE : A communication speed to Communicate
with external device. (2400, 4800, 9600, 19200).
- PRIVACY :
some part on screen to prevent private life
(Maximum 4 point covered).
①
ZONE : Enable user to set up a position from 0 to 3 area.
②
MASK : Enable user to set up screen output of chosen position.
③
V START : Mask Vertical start position.
④
V END : Mask Vertical end position.
⑤
H START : Mask Horizontal start position.
⑥
H END : Mask Horizontal end position.
⑦
COLOR : Set the mask color.
⑧
TRANSPARENCY : Set the transparency of the mask.
⑨
MOSAIC : Mosaic is set to mask the effect.
⑩
INITIAL : Enable user to initialize setting of
PRIVACY MENU
Enable user to choose any word in screen(Maximum 10 letter is available)
CAM TITLE
0123456789ABCDEFGHIJK
LMNOPQRSTUVWXYZ!-()<>
SPA>> <<BAK
TITLE SET
LOCATION [┛]
RETURN
[TITLE LOCATION]
TITLE SET
[U] [D] [L] [R] [M] <
Enable user to set up an OSD language
COMM ADJUST
>CAM ID
Privacy is the function that covers the
BAUDRATE 9600
RETURN
PRIVACY
>ZONE NO 0
MASK MODE ON
V START 7
V END 12
H START 10
H END 19
COLOR 1
TRANSPARENCY 0%
MOSAIC OFF
INITIAL
RETURN
1
22
9. OSD MANUAL
- MOTION DETECT : Motion detection function.
①
MOTION MODE : Enable user to set up ON/OFF
②
LEVEL : Enable user to setup a motion detect sensitivity (0~3)
③
V START : Motion area Vertical start position.
④
V END : Motion area Vertical end position.
⑤
H START : Motion area Horizontal start position.
⑥
H END : Motion area Horizontal end position.
⑦
INITIAL : Enable user to initialize setting of
MOTION DETECT
MOTION DETECT
>ZONE NO 0
MOTION MODE ON
LEVEL 4
V START 7
V END 12
H START 10
H END 19
INITIAL
RETURN
- DISPLAY :
MOTION DETECT.
①
Enable user to set up output on Camera ID screen
②
Enable user to set up output in xed CAM TITLE
③
MOTION on the screen as MOTION DETECT ON setting.
④
- DEFECT :
compensate up to 64 white pixels.
①
②
8. FACTORY DEFAULT
: Enable user to reset all of the status as the factory default Setting up using
LEFT, RIGHT KEY
9. EXIT
: Enable user to EXIT the OSD menu Setting up using LEFT, RIGHT KEY
Enable user to set up a screen marking of CAM ID, CAM TITLE,
CAM ID :
CAM TITLE :
MOTION DETECT: Enable user to set up out put of
INITIAL : Enable user to initialize of DISPLAY menu.
DISPLAY
CAM ID ON
CAM TITLE ON
MOTION DETECT ON
INITIAL
RETURN
The white pixel detection and compensation function can automatically detect and
COMPENSATION
DETECTION : White pixel detection..
DEFECT COMPENSATION On/Off..
:
DEFECT
>COMPENSATION ON
DETECTION (↑)
RETURN
23
10. Communication Protocol
Pelco “D” Protocol Commands
• Most widely used Commands
- TELE = UP KEY
- WIDE = DOWN KEY
- NEAR = LEFT KEY
- FAR = RIGHT KEY
- MENU = MENU KEY
24
Loading...