KT&C KPC-N570 Operation Manual

HIGH PERFORMANCE

Super Night Vision Camera

OP ER AT IO N MA NU AL

Than k you for c hoosing o ur high q uality c a m era.
Befo r e attemp t i ng to c o n nect or o perate, p l ease r e a d and fo l l ow
thes e instruc t i ons.

M08 3 - N 570-00 1

CONTE N T S

1. C AU TI ON S

2. F EA TU RE S

3. C OM PO NE NT S

4. N AM E AN D FU NC TI ON

5. I NS TA LL AT IO N

6. D IM EN SI ON S

7. S PE CI FI CA TI ON

8. O SD M AN UA L

3

1. CAUTI O N S

4

This device complies with Part 15 of the FCC
Rules. Operation is subject to the following two
conditions;

1. Th i s device m a y not c a u se harm f u l inter f e rence.

2. Th i s device m u st acce p t any in t e rferenc e receive d , includ i n g
i n terfere n c e that m a y cause u ndesire d o perati o n .

1. A regulated DC12V 3A power supply is recommended for use with this camera
for the best picture and the most stable operation.
An unregulated power supply can cause damage to the camera.

When unregulated power supply is applied, product warranty will be
out of subject.

2. It is recommended that the camera is used with a monitor that has a CCTV quality
75 video impedance level.
If your monitor is switched to high impedance then please adjust accordingly.

3. Do not attempt to disassemble the camera to gain access to the internal componets.
Refer servicing to your dealer.

4. Never face the camera towards the sun or any bright or reective light, which may

cause smear on the picture and possible damage to the CCD.

5. Do not remove the serial sticker for the warranty service.

This equipment has been tested and found to comply with the limits for a Class A digital
device, pursuant to part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference when the equipment is operated
in a commercial environment. This equipment generates, uses, and can radiate radio
frequency energy and, if not installed and used in accordance with the instruction
manual, may cause harmful interference to radio communications. Operation of this
equipment in a residential area is likely to cause harmful interference in which case the
user will be required to correct the interference at his own expense.”

Note-

Any changes or modifications in construction of this device
which are not expressly approved by the party responsible
for compliance could void the user’s authority to operate the
equipment.

Caution -

This is a class A product. In a domestic environment this product
may cause radio interference in which case the user may be
required to take adequate measures.

WARNING -

1. CAUTI O N S

5

Correct Disposal of This Product

(Waste Electrical & Electronic Equipment)

(Applicable in the European Union and other European countries with
separate collection systems)

This marking shown on the product or its literature, indicate that it should not
be disposed with other household wastes at the end of its working life. To
prevent possible harm to the environment or human health from uncontrolled
waste disposal, please separate this from other types of wastes and recycle it
responsibly to promote the sustainable reuse of material resources.

This product should not be mixed with other commercial wastes purchased this

product, or their local government ofce, for details of where and how they can

take item for environmentally safe recycling.

Business users should contact their supplier and check the terms and
conditions of the purchase contract.
Household users should contact either the retailer where they for disposal.

2. FE ATURES

• 1/3" 410K/470K Sony Super-HAD CCD

Ⅱ

Minimum illumination 0.1 Lux (F2.0, 30 IRE, Sense-Up Off)
S/N Ratio 50 dB

• High Resolution 580TV Lines

This camera has realized high resolution of 580TV lines using the top-notch full
digital image processing, 10 Bit A/D serial signal processing and special algorithm
technologies.

• 3D DNR (3D Digital Noise Reduction)

The DNR technology eliminates noise thus generating a distinct and clear image.
This camera DNR function utilizes an adaptive 3D Filter reducing noise caused by
movement.

• DAY&NIGHT

This camera has the DayNight function.
Day&Night operation feature an ‘auto’ mode which switches between day and night
mode automatically based upon the level of illumination on the scene.
And also, the COLOR mode operates in daytime conditions to provide optimum colors,

and B/W mode operates in night-time conditions to enhance the denition

of the

image.

• Privacy Mask Function

Privacy masking allows for the ‘blanking’ of specic areas of a scene, where the viewing

or recording of images is prohibited or undesired.

• OSD (On Screen Display)

This camera can easily controlled by multi-language OSD function on the monitor
screen.

6

3. CO M P ONENTS

SUPER NIGHT VISION
CAMERA

VIDEO OUTPUT
TEST CABLE

L-WRENCH,
SCREW - 3ea

OPERATION MANUAL

7

8

4. NA ME AND F U NCTION

①

Suns h i eld Fix i n g Bolt

②

Suns h i eld

③

Moun t i ng Brac k e t

④

IR I l l uminato r

LED : L e f t ( 35ea), R i g h t (35ea)

⑤

Phot o cell

⑥

Body

⑦

Body F ixing R i n g

①

⑤ ④④ ④

③

⑥

③ ②

Back

Cable Concealed Thru Bracke t

⑦

5. IN S TALLATION

• MOUNTING POSITION

9

360°

90°

15°

* 1st Axis * 2nd Axis

* 3rd Axis

360°

10

5. IN S TALLATION

• MONITOR CONNECTION

(1) DC12V

(2) DUAL(DC12V/AC24V)

DC12V

BNC FEMALE

DC12V POWER SUPPLY

VIDEO IN

DC12V/AC24V

BNC FEMALE

DC12V /AC24VPOWER SUPPLY

VIDEO IN

When you install the camera, please glue up the end of cable to
keep it stable in order to protect the camera from the humidity problems.

6. DI M E NSIONS

11

79.2

77.9

106.4

Ø60

175.5

145

129.4

263.4

135

125

Ø80

M12XP1

12

7. SP E C IFICAT ION

Signal Format NTSC PAL

Image Device

1/3" Sony Super HAD CCD

Ⅱ

Total Pixels

811(H) x 508(V) 795(H) x 596(V)

Effective Pixels

768(H) x 494(V) 752(H) x 582(V)

Inter. H/V

15,734/KHz(H), 59.94Hz(V) 15,625KHz(H), 50Hz(V)

H.Resolution

More than 580TV Lines

Minimum illumination

0.1Lux / F2.0

S/N Ratio

More than 50dB (AGC Off)

Sync Syste m

Internal

Gamma

r=0.05 ~1.0 Adjustable / USER

Video Output

1.0 Vp-p Composite(75Ω)

Lens

Varifocal

Electronic Shutter

1/60 sec

1/50 sec

Manual Shutter

1/60(50), FLK, 1/250, 1/500, 1/2K, 1/5K, 1/10K, 1/100K

X2, X4, X8, X16, X32, X64, X128, X256

Sense-up

Off / Auto (X2, X4, X8, X16, X32, X64, X128, X256)

AGC

Off / Low / Middle / High

BLC

Off / BLC / HSBLC

White Bala n c e

ATW / PUSH / PUSH-LOCK / MANUAL / Indoor / Outdoor

Day&Night

True Day & Night With ICR Mechanism

Motion Detection

Zone 4ea(Mask On / Off)

Privacy Zone

Zone 8ea(Mask On / Off)

3-DNR

Off / On(0~100 Level Adjustable)

D-WDR

Off / Indoor / Outdoor

Image

Freeze / Mirror / D-zoom / Sharpness / Color gain / Gamma / NEG.Image

OSD

Available

Language

Option1: English, French, Russian, German, Spanish,Dutch

Option2: English, Chinese

IR LED

850nm, 70ea, Up to 50m

IR LED Operation

On: 1Lux, Off: 3Lux

IP Rating

IP66(Weatherproof)

Operating Temperature

14˚F~122˚F(-10˚C ~ +50˚C)

Storage Temperature

-4˚F~140˚F(-20˚C ~ +60˚C)

Input Power
Source

DC12V

DC12V ±10% Max 1.2A

DUAL

AC24V ±10% Max 12.5W, DC12V ±10% Max 1.2A

Weight

Approx. 1200g

Option

DUAL(AC24V/DC12V)

13

8. OS D MANUAL

GENERAL STRUCTURE

SETUP MENU

LE NS

•BRI G H TNESS • RETURN

EX POSU RE

•SHU T T ER •B R I GHTNESS •AGC

•SEN S E -UP • B L C •D- W D R

•RET U R N

WH ITE BAL

•ATW •PUSH • PUSH-LO C K

•MAN U A L •IN D O OR •O U T DOOR

DA Y&NI GHT

•COL O R •B/W •AUTO

IM AGE

•FRE E Z E •MI R R OR •D - Z OOM

•SHA R P NESS • C OLOR GA I N

•GAM M A •NEG. I M AGE • R E TURN

3D NR

•LEV E L •RET U R N

SP ECIA L

•CAM T ITLE • L ANGUAGE

•MOT I O N •PR I V ACY • S Y NC

•RET U R N

RE SET

EX IT

14

8. OS D MANUAL

LENS MENU STRUCTURE

EXPOSURE MENU STRUCTURE

LENS

→

DC

→

BRIGHT

→

1~100

↕

EXPOSURE

↕

WHITE BAL

↕

DAY NIGHT

↕

IMAGE

↕

3DNR

↕

SPECIAL

↕

RESET

↕

EXIT

LENS SHUTTER

→

X256 ~1/100K

↕ ↕

EXPOSURE

→

AGC

→

LOW, MIDDLE, HIGH

↕ ↕

WHITE BAL SENSE-UP

→

X2 ~ X256

↕ ↕

GAIN, LEFT/RIGHT, WIDTH,

TOP/BOTTOM, HEIGNT

DAY NIGHT BLC

→

BLC

→

↕ ↕

IMAGE

↕

HSBLC

→

LEVEL, LEFT/RIGHT, WIDTH,

TOP/BOTTOM, HEIGNT

↕

3DNR D-WDR

→

INDOOR, OUTDOOR

↕

SPECIAL

↕

RESET

↕

EXIT

15

8. OS D MANUAL

WHITE BALANCE MENU STRUCTURE

DAY & NIGHT MENU STRUCTURE

LENS

↕

EXPOSURE

↕

WHITE BAL

→

ATW

↕ ↕

DAY NIGHT PUSH

↕ ↕

IMAGE P-LOCK

↕ ↕

3DNR MANUAL

→

BLUE 1~ 100

↕ ↕ ↕

SPECIAL INDOOR RED 1~ 100

↕ ↕

RESET OUTDOOR

↕

EXIT

LENS

↕

EXPOSURE

↕

WHITE BAL

↕

DAY NIGHT

→

AUTO

↕ ↕

IMAGE B/W

→

BURST

→

ON / OFF

↕ ↕

3DNR COLOR

↕

SPECIAL

↕

RESET

↕

EXIT

16

8. OS D MANUAL

IMAGE MENU STRUCTURE

3DNR MENU STRUCTURE

LENS FREEZE

→

ON/OFF

↕ ↕

EXPOSURE MIRROR

→

MIRROR

↔

V-FLIP

↔

ROATE

↕ ↕

WHITE BAL D-ZOOM

→

x1 ~ x32

↔

PAN -100~100

↔

TILT -100~100

↕ ↕

DAY NIGHT SHARPNESS

→

0 ~ 31

↕ ↕

IMAGE

→

COLOR GAIN

→

BLUE 1 ~100

↔

RED 1 ~100

↕ ↕

3DNR GAMMA

→

0.05~1

↕ ↕

SPECIAL NEG.IMAGE

→

ON/OFF

↕

RESET

↕

EXIT

LENS

↕

EXPOSURE

↕

WHITE BAL

↕

DAY NIGHT

↕

IMAGE

↕

3DNR

→

ON

→

LEVEL

→

1~100

↕

SPECIAL

↕

RESET

↕

EXIT

17

8. OS D MANUAL

SPECIAL MENU STRUCTURE

LENS

↕

EXPOSURE

↕

WHITE BAL

CAM TITLE

→

ON / OFF

↔

POSITION CONTROL

↕

↕

DAY NIGHT

LANGUAGE

→

ENGLISH

↔

FRANÇAIS

↔

РУССКИЙ

↔

ESPAÑOL

↔

DEUTSCH

↕

IMAGE

ON /

OFF

AREA

SEL

AREA

DISPLAY

LEFT /
RIGHT

WIDTH

TOP /

BOTTOM

↕

MOTION

→ ↔ ↔ ↔ ↔ ↔

3DNR

↕

↕

AREA 1~4 ON/OFF

MOTION

VIEW

↔

SENSITIVITY

↔

HEIGHT

SPECIAL

→

PRIVACY

→

AREA SEL

↔

AREA DISPLAY

↔

LEFT/RIGHT

↔

WIDTH

↔

TOP/BOT TOM

↕ ↓ ↓ ↕

RESET

AREA 1~8

ON/OFF

COLOR

↔

HEIGHT

↕

EXIT

SYNC

→

INT

RESET MENU STRUCTURE

LENS

↕

EXPOSURE

↕

WHITE BAL

↕

DAY NIGHT

↕

IMAGE

↕

3DNR

↕

SPECIAL

↕

RESET

→

FACTORY RESET

↕

EXIT

18

8. OS D MANUAL

OSD FUNCTION DESCRIPTION

1.LENS

- LEVEL DC
BRIGHTNESS : Enable user to select the
DC level for Brightness of image(1~100).

2. EXPOSURE

: Enable user to set up the function of SHUTTER, AGC.

- SHUTTER

• FLK : Enable user to set up the FLICKERLESS.
(NTSC: 1/100, PAL: 1/120)

• FIXED : Enable user to set up the Shutter Speed.
> 1/60(50), 1/250, 1/500, 1/2K, 1/5K, 1/10K, 1/100K.
* ( ) is for PAL TYPE.

- BRIGHTNESS : Enable user to set up the MANUAL
electronic Shutter value.

- AGC : Enable user to make imager bright to
amplify the Gain.

- SENSE-UP : Low-speed shutter control.

- BLC : The Function of Back Light Compensation.

• HSBLC : Highlight Suppression BLC will darken
image portions for clearer images.

- D-WDR : allows every detail to be captured accurately
even if one portion is bright while other portions are dark.

LENS

BRIGHT 50
RETURN RET

┛

EXPOSURE

SHUTTER 1/60
BRIGHTNESS 50
AGC OFF
SENSE-UP AUTO
BLC BLC

┛

D-WDR OFF
RETURN RET

┛

19

8. OS D MANUAL

3. WHITE BALANCE

: Enable user to represent the accurate white color by controlling the R.G.B level.

• ATW :

Enable user to trace the White Balance
automatically in the Wide range.
(2,500K ~ 9,500K)

• PUSH :

Enable user to trace the White Balance

automatically in all the range.

• P-LOCK :

Enable user to set up automatically

readjusted only at the request of the user.

• MANUAL

: Enable user to set the RED

GAIN or BLUE GAIN.

• INDOOR

: Enable user to set up 3,200K base mode.

• OUTDOOR

: Enable user to set up 5,400K base mode.

4. DAY&NIGHT

: Conversion of output image COLOR/BW depending on exterior environment.

- AUTO : Sensor mode auto change.

- B/W : Enable user to x the output image in B/W.

• BURST ON/OFF : Select the burst signal ON/OFF
when Night condition.

- COLOR : Enable user to x the output image in COLOR.

WHITE BAL MANUAL

BLUE 24
RED 32
RETURN RET

┛

20

8. OS D MANUAL

5. IMAGE

:Setting up the FREEZE, MIRROR, D-ZOOM, SHARPNESS, COLOR GAIN,
GAMMA, NEGATIVE IMAGE.

- FREEZE : Setting of moving images in
freeze-frame mode.

- MIRROR

• MIRROR : Enable user to set up
reversed LEFT and RIGHT image.

• V-FLIP : Enable user to set up vertically

ipped video.

• ROTATION : Enable user to set up 180-degree

rotation lp function.

- D-ZOOM : Enable user to expand one part
of the monitor screen for viewing.

- SHARPNESS : Enable user to set up
sharpness control.

- COLOR GAIN : Enable user to set the
RED GAIN or BLUE GAIN.

- GAMMA : Enable user to set up compensation
according to gamma value.

- NEG.IMAGE : Enable user to set up negative
image ON/OFF.

6. 3DNR

: three-dimensional noise reduction.

- LEVEL : Enable user to set up noise
reduction level.

IMAGE

FREEZE OFF
MIRROR OFF
D-ZOOM ON

┛

SHARPNESS 5
COLOR GAIN

┛

GAMMA 0.45
NEG.IMAGE OFF
RETURN RET

┛

3DNR

LEVEL 50
RETURN RET

┛

21

8. OS D MANUAL

7. SPECIAL

: Setting up the CAM TITLE, LANGUAGE, MOTION, PRIVACY, SYNC.

- CAMERA TITLE : Display the title editing menu.

- LANGUAGE : Enable user to set up Language for OSD.
(Option1: English, Russian, Spanish, German, French
Option2: English, Chinese)

- MOTION : The camera monitors the movement of image,
and it sends an alarm signal or OSD icon.

• AREA SELECT : Enable user to select the 4 motion area.

• AREA DISPLAY : Enable user to set up ON/OFF in selected area

• LEFT/RIGHT : Enable user to set up LEFT/RIGHT position in selected area.

• WIDTH : Enable user to set up width in selected area.

• TOP/BOTTOM : Enable user to set up TOP/BOTTOM position in selected area.

• HEIGHT : Enable user to set up height in selected area.

• SENSITIVITY : Enable user to set up the movement detection threshold value.

• MOTION VIEW : Display the motion area on the screen.

- PRIVACY : Privacy is the function that covers the some part on screen to prevent
private life Maximum 8 point covered.

• AREA SELECT : Enable user to set up a area from 1 to 8.

• AREA DISPLAY : Enable user to set up ON/OFF in selected area.

• LEFT/RIGHT : Enable user to set up LEFT/RIGHT position in selected area.

• WIDTH : Enable user to set up width in selected area.

• TOP/BOTTOM : Enable user to set up TOP/BOTTOM position in selected area.

• HEIGHT : Enable user to set up height in selected area.

• COLOR : Enable user to set up MASK COLOR.

- SYNC : Synchronization pulses for lock the viewing monitor on the picture.

• INT : Internal Synchronization system.

SPECIAL

CAM TITLE OFF
LANGUAGE ENGLISH
MOTION ON

┛

PRIVACY ON

┛

SYNC INT
RETURN RET

┛

22

8. OS D MANUAL

8. RESET

: Enable user to reset all of the status as the factory default.

RESET

FACTORY RESET

┛

RETURN RET

┛