KT&C KPC-LV40NU User Manual

M150-LD40LV40-001

HIGH PERFORMANCE

WDR FLAT DOME CAMERA

OPERATION MANUAL

VANDAL DOME

PLASTIC DOME

Before attempting to connect operate this unit, please read and follow these instructions.

Thank you for choosing our high quality camera.

CONTENTS

1. CAUTIONS

2. IMPORTANT SAFETY INSTRUCTION

3. EQUIPMENT AND ACCESSORIES

4. CAMERA COMPONENT DESCRIPTIONS

• Plastic Dome / Vandal Dome Type

5. INSTALLATION

• Plastic Dome / Vandal Dome Type

6. DIMENSIONS

• Plastic Dome / Vandal Dome Type

7. SPECIFICATION

8. OSD MANUAL

• Menu structure

• Function Description

CAUTION

These servicing instructions are for use by qualied service personnel only.
To reduce the risk of electric shock do not perform any servicing o ther than
that contained in the operating instructions unless you are qualied to do so.

Use Class 2 Power Supply Only

2

1. CAUTIONS

This device complies with Part 15 of the FCC Rules.
Operation is subject to the following two conditions;

1. This device may not cause harmful interference.

2. This device must accept any interference received, including
interference that may cause undesired operation.

Note

This equipment has been tested and found to comply with the limits for a Class A
digital device, pursuant to part 15 of the FCC Rules. These limits are designed to
provide reasonable protection against harmful interference when the equipment is
operated in a commercial environment. This equipment generates, uses, and can
radiate radio frequency energy and, if not installed and used in accordance with
the instruction manual, may cause harmful interference to radio communications.
Operation of this equipment in a residential area is likely to cause harmful
interference in which case the user will be required to correct the interference at his
own expense.”

WARNING

This is a class A product. In a domestic environment this product may cause radio
interference in which case the user may be required to take adequate measures.

Caution

Any changes or modications in construction of this devices which are not expressly

approved by the party responsible for compliance could void the user’s authority to
operate the equipment.

1. A regulated DC12V 300mA power supply is recommended for use with
this camera for the best picture and the most stable operation.
An unregulated power supply can cause damage to the camera.

When unregulated power supply is applied, product warranty will be out
of subject.

2. It is recommended that the camera is used with a monitor that has a CCTV
quality 75 video impedance level. If your monitor is switched to high impedance
then please adjust accordingly.

3. Do not attempt to disassemble the camera to gain access to the internal
components. Refer servicing to your dealer.

4. Never face the camera towards the sun or any bright or reective light, which

may cause smear on the picture and possible damage to the CCD.

5. Do not remove the serial sticker for the warranty service.

6. Do not expose the camera to rain or other types of liquid.

7. The apparatus must be connected to a mains socket-outlet with a protective
earthing connection.

3

1. CAUTIONS

Correct Disposal of This Product

(Waste Electrical & Electronic Equipment)

(Applicable in the European Union and other European
countries with separate collection systems)

This marking shown on the product or its literature, indicate that it should not be
disposed with other household wastes at the end of its working life. To prevent
possible harm to the environment or human health from uncontrolled waste
disposal, please separate this from other types of wastes and recycle it responsibly
to promote the sustainable reuse of material resources.
This product should not be mixed with other commercial wastes purchased this

product, or their local government ofce, for details of where and how they can

take item for environmentally safe recycling.
Business users should contact their supplier and check the terms and conditions of
the purchase contract.
Household users should contact either the retailer where they for disposal.

CAUTION

RISK OF ELECTRIC SHOCK DO NOT OPEN

CAUTION:

TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT
REMOVE COVER (OR BACK). NO USER. SERVICEABLE
PARTS INSIDE. REFER SERVICING TO QUALIFIED
SERVICE PERSONNEL

This symbol is intended to alert the user to the presence of un­insulated “dangerous voltage” within the product’s enclosure
that may be of sufficient magnitude to constitute a risk of
electric shock to persons.

This symbol is intended to alert the user to the presence of
important operating and maintenance (servicing) instructions
in the literature accompanying the appliance

4

2. IMPORTANT SAFETY INSTRUCTION

1) Read these instructions.

2) Keep these instructions.

3) Heed all warnings.

4) Follow all instructions.

5) Do not use this apparatus near water.

6) Clean only with dry cloth.

7) Do not block any ventilation openings. Install in accordance
with the manufacturer’s instructions.

8) Do not install near any heat sources such as radiators, heat registers,

stoves, or other apparatus (including ampliers) that produce heat.

9) Do not defeat the safety purpose of the polarized or grounding-type plug. A
polarized plug has two blades with one wider than the other. A grounding type plug
has two blades and a third grounding prong. The wide blade or the third prong are

provided for your safety. If the provided plug does not t into your outlet, consult

an electrician for replacement of the obsolete outlet.

10) Protect the power cord from being walked on or pinched particularly at plugs,
convenience receptacles, and the point where they exit from the apparatus.

11) Only use attachments/accessories specied by the manufacturer.

12) Use only with the cart, stand, tripod, bracket, or table specied by

the manufacturer, or sold with the apparatus. When a cart is used,

use caution when moving the cart/apparatus combination to

avoid injury from tip-over.

13) Unplug this apparatus during lightning storms or when unused for long

periods of time.

14) Refer all servicing to qualied service personnel. Servicing is required when

the apparatus has been damaged in any way, such as power-supply cord or plug
is damaged, liquid has been spilled or objects have fallen into the apparatus, the
apparatus has been exposed to rain or moisture, does not operate normally, or
has been dropped.

5

3. EQUIPMENT AND ACCESSORIES

Plastic Dome Type Mount Guide (Plastic Dome Type)

Vandal Dome Type Mount Guide (Vandal Dome Type)

Manual

Screws(3ea) / L-Wrench Service Video Output Test Cable / Fixed Tape

6

4. CAMERA COMPONENT DESCRIPTIONS

• Plastic Dome Type

1

2

3

4

5

6

7

NO PART NAME

8

1 Top Case

2 Dome Cover

3 Dome Bracket

4 Dome Ass'y

5 Cable

6 Main PCB

7 OSD Controller

8 Bottom Case

7

4. CAMERA COMPONENT DESCRIPTIONS

• Vandal Dome Type

1

2

3

4

5

6

7

8

NO PART NAME

1 Top Case

2 Dome Cover

9

3 Case Rubber

4 Dome Bracket

5 Dome Ass'y

6 Main PCB

7 Safety Wire

8 OSD Controller

9 Bottom Case

8

5. INSTALLATION

1. Attach the FLAT DOME on the ceiling with using
the screws provided, considering the camera
angle required for the surveillance function.

2. Adjust the LENS ANGLE to the desired
location by hand.

3. Connect the VIDEO OUT CABLE and check the
video image. Change the SETTINGS accordingly
using the OSD controller.

<TILT ANGLE : 20~90°>

TILT: +90°

<PAN ANGLE : ±10°>

(Plastic Dome)

TAPPING SCREW (4 x 20L) - 3EA

OSD CONTROLLER

TILT: 0°

TILT: +20°

SECOND VIDEO CABLE

* FIXED TAPE: It attached when you install the
product in areas where vibration occurs.

FIXED TAPE attached examples.

PAN: ±10°

PAN: 0°

4. After the LENS SETTING is completed,
install the TOP COVER.

ASSEMBLY HOOK

(2 point)

* FIXED TAPE

TILT 45° when attaching TILT 90° when attaching

TOP HOUSING

(Assembly direction)

TOP HOUSING

(Separation Direction)

M4 STAR SCREW

9

L-WRENCH(T-20)

5. INSTALLATION

1. Attach the FLAT DOME on the ceiling with using the screws
provided, considering the camera angle required for the
surveillance function.

2. Adjust the LENS ANGLE to the desired
ocation by hand.

3. Please remove the protective lm when installing.

(Vandal Dome)

TAPPING SCREW (4 x 20L)-3EA

4. Connect the VIDEO OUT CABLE and check the video image.
Change the SETTINGS accordingly using the OSD controller.

<TILT ANGLE : 20~90°>

TILT: +90°

<PAN ANGLE : ±10°>

PAN: ±10°

PAN: 0°

TILT: 0°

TILT: +20°

OSD CONTROLLER

SECOND VIDEO CABLE

* FIXED TAPE: It attached when you install the
product in areas where vibration occurs.

FIXED TAPE attached examples.

TILT 45° when attaching TILT 90° when attaching

* FIXED TAPE

5. After the LENS SETTING is completed, install the TOP COVER.

*CASE RUBBER:

Before assembling the top housing,

Be sure the Rubber correctly positioned.

M4 STAR SCREW

L-WRENCH(T-20)

10

* Protective lm

5. INSTALLATION

• MONITOR CONNECTION

- DC12V/AC24V

CAMERA

- DC12V

CAMERA

DC12V/AC24V

(TERMINAL BLOCK)

BNC FEMALE

DC12V
(DC JACK)

BNC FEMALE

DC12V/AC24V

POWER SUPPLY

VIDEO IN

DC12V ADAPTER

VIDEO IN

MONITOR

MONITOR

When you install the camera, please glue up the end of cable to
keep it stable in order to protect the camera from the humidity problems.

11

6. DIMENSIONS

• Plastic Dome Type • Vandal Dome Type

119

119

139

42

134

49

Unit(mm)

12

7. SPECIFICATION

Image Sensor 1/3” 960H SONY Double Scan Super HAD CCD II

Scanning System 2 : 1 Interlace

H Resolution. 750TV Lines

Scanning Frequency 15.734KHz(H), 59.94Hz(V) 15 .625KHz( H) , 50 Hz (V )

Total Pixels No. 1028(H) X 508(V) 1028(H) X 596(V)

Effective Pixels No. 976(H) X 494(V) 976(H) X 582(V)
S/N Ratio More than 50dB(AGC OFF, 3DNR ON)

Min. Illumination Color:0.1Lux, BW:0.1Lux (30IRE@F2.0, AGC 36dB) 0.000001Lux (DSS x256)

Sync System Internal

Gamma r= 0.45
Video Output 1.0 Vp-p Composite(75Ω)

Lens Board Lens
Digital Zoom Ratio 3x
Electronic Shutter 1/60 ~1/100,000sec 1/50 ~1/100,000sec
Digital Slow Shutter OFF, 2 ~ 256 Field

Flickerless ON / OFF
WDR ON / OFF (Level adjustable)
BLC ON / OFF (Level adjustment, Area selection)
HLC ON / AUTO / OFF (Level adjustable)

AGC OFF, 6 ~ 36dB

DNR(2D/3D) ON / OFF (Level adjustable)

Image Function Image reverse(Normal/Flip), Freeze, Contrast, Sharpness
Day & Night COLOR / BW / AUTO(DIGITAL D/N)

Motion Detection 4 Zones (Level adjustable, Area adjustment)
Privacy Masking 15 Zones (Area adjustment)

White Balance

OSD Built in (Joystick)

Language

Operating Temperature 14°F~122°F(-10°C~+50°C)

Storage Temperature -4°F~140°F(-20°C~+60°C)
Humidity Less than 80%

Weight

Power
Consumption

Dimension (mm)

DC DC12V (±10%), Max. 140mA

DUAL

Specications and designs are subject to change for improving the

NTSC PAL

ATW / PUSH / USER1 / USER2 / ANTI CR /

MANUAL / PUSH-LOCK

ENGLISH / JAPANESE / GERMAN / FRENCH /

RUSSIAN / PORTUGUESE / SPANISH / CHINESE

PLASTIC DOME Type: Approx. 200g
VANDAL DOME Type: Approx. 500g

DC12V (±10%), Max. 190mA

AC24V (±10%), Max. 2.5W

PLASTIC DOME Type: 119mm x 119mm x 42mm

VANDAL DOME Type: 139mm x 134mm x 49mm

functionality of this product without notice.

13

8. OSD MANUAL

• Menu structure

Main MENU 1st Sub MENU 2nd Sub MENU 3rd Sub MENU 4th Sub MENU 5th Sub MENU

HIGH LUMINANCE

EXPOSURE

WHITE
BALANCE

DAY&NIGHT

AUTO

MANUAL

ATW

PUSH

USER1

USER2

ANTI CR

MANUAL

PUSH LOCK

COLOR

AUTO

BW

LOW LUMINANCE

RETURN

MODE SHUT, SLOW

SHUT

AGC 6, 12, 18, 24, 30, 36, 42, 44.8

RETURN

SPEED 0 ~ 255

DELAY CNT 0 ~ 255

ATW FRAME x0.5, x1.0, x1.5, x2.0

ENVIRONMENT INDOOR, OUTDOOR

RETURN

B-GAIN 0 ~ 255

R-GAIN 0 ~ 255

RETURN

B-GAIN 0 ~ 255

R-GAIN 0 ~ 255

RETURN

LEVEL UP PUSH ENTER

LEVEL DOWN PUSH ENTER

PRESET

RETURN

BURST OFF, ON

DELAY CNT 0 ~ 255

DAY > NIGHT 0 ~ 255

NIGHT > DAY 0 ~ 255

RETURN

BURST OFF, ON

RETURN

FLICKERLESS OFF / ON

BRIGHTNESS 0 ~ 255

MODE

AGC MAX 6, 12, 18, 24, 30, 36

DSS MAX 2, 4, 8, 16, 32, 64, 128, 256

BRIGHTNESS x0.25, x0.5, x0.75, x1.0

MODE (SHUT) ONLY

1/50(PAL), 1/60(NTSC), 1/100(NTSC), 1/120(PAL),
1/250, 1/500, 1/1000, 1/2000, 1/4000, 1/10000

MODE (SLOW) ONLY 2, 4, 8, 16, 32, 64, 128, 256

AGC, SLOW, AGC > SLOW, SLOW >
AGC, OFF

14

8. OSD MANUAL

Main MENU 1st Sub MENU 2nd Sub MENU 3rd Sub MENU 4th Sub MENU 5th Sub MENU

WDR MODE OFF, ON

WDR/BLC

DNR

IMAGE

SPECIAL

FACTORY
DEFAULT

EXIT
SAVE&EXIT

BLC MODE OFF, ON

HLC MODE OFF, ON, AUTO

2DNR MODE OFF, ON
2DNR LEVEL 0 ~ 15
3DNR MODE OFF, ON
3DNR LEVEL 0 ~ 63
RETURN
HV-FLIP OFF, ON
FREEZE OFF, ON
EZOOM 1.0x ~ 3.0x
CONTRAST 0 ~ 63
SHARPNESS 0 ~ 15
RETURN
CAMERA TITLE OFF, ON DISPLAY THE TITLE EDITING MENU

LANGUAGE

PRIVACY

MOTION DET OFF, ON

ENGLISH / 中文 /
PORTUGUÊS / 日本語

AREA SEL 1/15 ~ 15/15
MODE OFF, ON
POSITION NEXT: PUSH ENTER

COLOR

TRANSP 0.00, 0.50, 0.75, 1.00
MOSAIC OFF, ON
RETURN

LEVEL 0 ~ 15
CONTRAST1 0 ~ 7
CONTRAST2 0 ~ 4
RETURN

ZONE

LEVEL 0 ~ 15
RETURN
CLIP LEVEL 0 ~ 255
SCALE 0 ~ 15
RETURN

RETURN

Р у с с к и й

"WHITE, BLACK, RED, GREEN, BLUE,
YELLOW, CYAN, MAGENTA"

DETECT SENSE 0 ~ 127
BLOCK DISP OFF, ON

MONITOR AREA

CENTER, TOP, BOTTOM,
LEFT, RIGHT

/ ESPAÑOL / DEUTSCH / FRANCAIS /

AREA SEL 1/4 ~ 4/4
MODE OFF, ON
TOP 0 ~ 15
BOTTOM 0 ~ 15
LEFT 0 ~ 23
RIGHT 0 ~ 23
RETURN

15