M152-LP751-002
High Contrast License Plate
Capture Camera
OPERATION MANUAL
Thank you for choosing our high quality camera.
Before attempting to connect or operate this unit, please read and follow these
instructions.
Contents
1. Cautions
2. Important Safety Instructions
3. Features
4. Components
5. Product Diagrams
6. Installation Diagrams
7. Functions
8. Installation Guidelines
9. Specifications
10. Dimensions
CAUTION
These servicing instructions are for use by qualied service personnel only.
To reduce the risk of electric shock do not perform any servicing o ther than
that contained in the operating instructions unless you are qualied to do so.
Use Class 2 Power Supply Only
2
1. Cautions
This device complies with Part 15 of the FCC Rules.
Operation is subject to the following two conditions:
1. This device may not cause harmful interference.
2. This device must accept any interference received, including
interference that may cause undesired operation.
Note -
This equipment has been tested and found to comply with the limits
for a Class A digital device, pursuant to part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against
harmful interference when the equipment is operated in a commercial
environment. This equipment generates, uses, and can radiate radio
frequency energy and, if not installed and used in accordance with
the instruction manual, may cause harmful interference to radio
communications. Operation of this equipment in a residential area
is likely to cause harmful interference in which case the user will be
required to correct the interference at his own expense.
WARNING -
This is a class A product. In a domestic environment this product may
cause radio interference in which case the user may be required to take
adequate measures.
Caution -
Any changes or modifications in construction of this device which are
not expressly approved by the party responsible for compliance could
void the user’s authority to operate the equipment.
1. A regulated DC12V 3A power supply is recommended for use with this camera
for the best picture and the most stable operation.
An unregulated power supply can cause damage to the camera.
When an unregulated power supply is applied, the product warranty will be
void.
2. It is recommended that the camera be used with a monitor that has a CCTV quality
75 video impedance level.
If your monitor is switched to high impedance then please adjust accordingly.
3. Do not attempt to disassemble the camera to gain access to the internal componets.
Refer servicing to your dealer.
4. Never face the camera towards the sun or any bright or reective light, which may
cause smears on the picture and possible damage to the image sensor.
5. Do not remove the serial sticker for the warranty service.
3
1. Cautions
(Waste Electrical & Electronic Equipment)
WEEE
This marking shown on the product or its literature, indicates that it should
not be disposed with other household wastes at the end of its working
life. To prevent possible harm to the environment or human health from
uncontrolled waste disposal, please separate this from other types of
wastes and recycle it responsibly
to promote the sustainable reuse of material resources. Household users
should contact either the retailer where they purchased this product, or
their local government ofce, for details of where and how they can take
item for environmentally safe recycling.
Business users should contact their supplier and check the terms and
conditions of the purchase contract.
This product should not be mixed with other commercial wastes for
disposal.
CAUTION
RISK OF ELECTRIC SHOCK DO NOT OPEN
CAUTION:
TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT
REMOVE COVER (OR BACK). NO USER SERVICEABLE
PARTS INSIDE. REFER SERVICING TO QUALIFIED
SERVICE PERSONNEL
This symbol is intended to alert the user to the presence
of un-insulated “dangerous voltage” within the product’s
enclosure that may be of sufcient magnitude to constitute a
risk of electric shock.
This symbol is intended to alert the user to the presence of
important operating and maintenance (servicing) instructions
in the literature accompanying the appliance.
4
2. Important Safety Instruction
1) Read these instructions.
2) Keep these instructions.
3) Heed all warnings.
4) Follow all instructions.
5) Do not use this apparatus near water.
6) Clean only with dry cloth.
7) Do not block any ventilation openings. Install in accordance
with the manufacturer’s instructions.
8) Do not install near any heat sources such as radiators, heat registers,
stoves, or other apparatus (including ampliers) that produce heat.
9) Do not defeat the safety purpose of the polarized or grounding-type plug.
A polarized plug has two blades with one wider than the other. A grounding
type plug has two blades and a third grounding prong. The wide blade or the
third prong are provided for your safety. If the provided plug does not t into
your outlet, consult an electrician for replacement of the obsolete outlet.
10) Protect the power cord from being walked on or pinched particularly
at plugs, convenience receptacles, and the point where they exit from the
apparatus.
11) Only use attachments/accessories specied by the manufacturer.
12) Use only with the cart, stand, tripod, bracket, or table specied by the
manufacturer, or sold with the apparatus. When a cart is used,
use caution when moving the cart/apparatus combination to
avoid injury from tip-over.
13) Unplug this apparatus during lightning storms or when unused for long
periods of time.
14) Refer all servicing to qualied service personnel. Servicing is required
when the apparatus has been damaged in any way, such as power-supply
cord or plug is damaged, liquid has been spilled or objects have fallen into
the apparatus, the apparatus has been exposed to rain or moisture,
does not operate normally, or has been dropped.
5
3. Features
• 1/3" 960H SONY EXview HAD CCD
• High Resolution 700TV Lines
• Special filter and IR LED provides maximum readability
despite headlight glare
• Plate capture up to 75mph (120Km/H)
• 5.0 ~ 50.0mm Vari-focal lens captures license plate
from 16ft ~ 65ft (5M ~ 20M)
• IP67 rated Water Proof
• Cable concealed bracket
• DC12V / AC24V Dual power with auto-polarity
Ⅱ
4. Components
LP Camera
Video Output
Test Cable
L-Wrench / Screws
Operation Manual
6
5. Product Diagrams
①
③
④
②
①
Sunshield
②
Cable Concealed
Bracket
③
LED : 10ea
④
Body
• CONTROL FUNCTION
(OSD JOYSTICK)
LEFT
MENU
UP
RIGHT
DOWN
7
5. Product Diagrams
Built in heater protects the camera from low temperatures.
(Operating temperature with Heater: -40℃)
Heater
External Zoom & Focus Adjuster
8
6. Installation Diagrams
• MOUNTING POSITION
90˚TILT
90˚TILT
360˚PAN
360˚PAN
9
6. Installation Diagrams
• Monitor Connection
DC12V
DC12V
DUAL(DC12V/AC24V)
DC12V/AC24V
When you install the camera, please glue the end of cable to
keep it stable in order to protect the camera from humidity problems.
• Service Video Connector
DC 12V Power Supply
VIDEO IN Monitor
DC 12V Power Supply or
AC 24V Power Supply
Video In Monitor
Handheld Monitor
10
7. Functions
OSD Menu Structure
• MODE
- INSTALLATION
Installation Mode provides a bright
video screen for adjusting the angle and focus.
- LICENSE-PLATE
License-plate Mode provides high contrast
and clear license plate images for license plate capture.
SETUP
▶
MODE
SHUTTER
NEG. IMAGE
EXIT
LICENSE-PLATE
1/9000
OFF
• SHUTTER
1/250,1/500 ~ 1/10000
1/30K,1/50K, 1/70K, 1/90K, 1/100K.
- Adjusted when LICENSE-PLATE MODE is
performed(Initial value: 1/9000).
- Indicated as “----“ when INSTALLATION MODE
is set.
• NEGATIVE
The user can select positive or negative image.
Negative OFF
(adjusted to 1/500sec measure),
Negative ON
• EXIT
Enables user to EXIT the OSD menu by using
SELECT. If Installation Mode is
selected, the user can see the screen as below.
11
SETUP
MODE
LICENSE-PLATE
SHUTTER
▶
NEG. IMAGE
EXIT
SETUP
MODE
LICENSE-PLATE
SHUTTER
▶
NEG. IMAGE
EXIT
INSTALLATION MODE
FOCUS VALUE: 2↑
1/9000
OFF
1/9000
OFF
8. Installation Guidelines
Camera Height
Must consider height in distance calculation.
•
Sharper angle will alter appearance of plate.
•
Camera Height (Ft) Horizontal Distance (Ft) Capture Distance(Ft)
10 10 14.14
11 20 22.83
12 30 32.31
13 40 42.06
14 50 51.92
12
8. Installation Guidelines
Camera Angles
Both the vertical and the horizontal angle must be less than 30
•
degrees in order to get an optimal view of the license plate.
V-angle less than 30˚ (correct) H-angle less than 30˚ (correct)
Capture Zone
Wide angle provides a shorter capture distance.
•
Tele angle provides a longer capture distance.
•
What will the plate look like on screen?
WIDE SETTING -66.5 @ f=5mm
TELE SETTING -7.4 @ f=50mm
WIDE END -66.5 @ f=5mm
TELE END -7.4 @ f=50mm
o
o
(All pictures taken with high-beam)
Optimized Capture
Range for S/W
License Plate can be
recongnizable with eyes
13
8. Installation Guidelines
Lane Width
Narrow lanes = less variation in plate location.
•
Wider lanes = more variation in plate location.
•
Lens should cover entire width of the lane.
•
Ensure that the horizontal eld of view is wide enough.
•
Speed
Camera can capture moving vehicles up to 75mph.
•
Keep camera as low as possible.
•
Minimize horizontal angle.
•
Zoom in the lens as close as possible.
•
Up to 75 mph
14
8. Installation Guidelines
DVR
Camera is fully compatible with industry standard DVRs.
•
Check compression settings.
•
Non-conditional refresh compression. (i.e. MJPEG or JPEG)
•
D1 (720x480) resolution.
•
30fps (each channel) for best results.
•
9. Specifications
Signal Format NTSC PAL
Image Device 1/3" 960H SONY EXview HAD CCD II
Scanning System 2 : 1 Interlace
Total Pixels 1020(H) X 508(V) 1020(H) X 596(V)
Effective Pixels 976(H) X 494(V) 976(H) X 582(V)
Inter. H/V 15.734KHz(H), 59.94Hz(V) 15.625KHz(H), 50Hz(V)
H.Resolution 70TV Lines
Minimum Illumination 0 Lux (IR LED ON)
S/N Ratio More than 50dB (AGC Off)
Sync System Internal
Gamma r= 0.45
Video Output 1.0 Vp-p Composite(75Ω)
Negative Image On / Off
Function Focus Adjust MODE
Day & Night BW
Lens 5-50mm DC Drive Vari-focal lens
IR LED 850nm, Power LED, 10EA
License
Plate
Capture
Operating Temperature
Storage Temperature -4˚F~140˚F(-20˚C ~ +60˚C)
Power
Consumption
Weight Approx. 1.37Kg
Dinmension(mm) 98.6(W) x 83(H) x 126(D)
IP Rating IP67 (rated WaterProof)
Speed Rage Up to 75mph (120km/h)
Capture
Distance
Capture Angle Maximum 30 degree offset
DC
DC
DUAL
AC
* Specications and designs are subject to change for improving
the functionality of this product without notice.
16ft ~ 65ft (5m ~ 20m)
14°F~122°F(-10°C~+50°C) /
Heater On: -40°F~122°F(-40°C~+50°C)
DC12V(±10%), Max 700mA (Without Heater)
DC12V(±10%), Max 1.6A (With Heater)
DC12V(±10%), Max 760mA (Without Heater)
DC12V(±10%), Max 990mA (With Heater)
AC24V(±10%), Max 9W (Without Heater)
AC24V(±10%), Max 20W (With Heater)
15
10. Dimensions
unit: mm
Power LED(10ea)
98.6
89.5
83.0
140
126.0
M12XP1.25
16
(256.5)
Ø95
(2EA)
106.5
10
135
125
Mount Guide
4-ø6.0
Loading...