KT&C KPC-HNV522MB User Manual

M151-HNV522-001

HD CCTV
Digital Video
IR LED Dome Camera

User Manual

Thank you for choosing our high quality camera.
Before attempting to connect operate this unit, please read and follow these instructions.

CAUTION

These servicing instructions are for use by qualied service personnel only.

To reduce the risk of electric shock do not perform any servicing other than that

contained in the operating instructions unless you are qualied to do so.

Use Class 2 Power Supply Only

2

CONTENTS

1. CAUTIONS

2. IMPORTANT SAFETY INSTRUCTION

3. FEATURES

4. EQUIPMENT AND ACCESSORIES

5. CAMERA COMPONENT DESCRIPTIONS

6. INSTALLATION

7. DIMENSIONS

8. SPECIFICATION

9. OSD MANUAL

3

1. CAUTIONS

This device complies with Part 15 of the FCC Rules.
Operation is subject to the following two conditions;

1. This device may not cause harmful interference.

2. This device must accept any interference received, including interference
that may cause undesired operation.

Note

This equipment has been tested and found to comply with the limits for a Class A digital
device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable
protection against harmful interference when the equipment is operated in a commercial
environment. This equipment generates, uses, and can radiate radio frequency energy
and, if not installed and used in accordance with the instruction manual, may cause harmful
interference to radio communications. Operation of this equipment in a residential area is
likely to cause harmful interference in which case the user will be required to correct the
interference at his own expense.”

WARNING

This is a class A product. In a domestic environment this product may cause radio interference
in which case the user may be required to take adequate measures.

Caution

Any changes or modications in construction of this devices which are not expressly approved

by the party responsible for compliance could void the user’s authority to operate the
equipment.

1. A regulated DC12V 500mA power supply is recommended for use with this camera
for the best picture and the most stable operation.

An unregulated power supply can cause damage to the camera.
When unregulated power supply is applied, product warranty will be out of subject.

2. It is recommended that the camera is used with a monitor that has a CCTV quality 75Ω video

impedance level. If your monitor is switched to high impedance then please adjust accordingly.

3. Do not attempt to disassemble the camera to gain access to the internal components.
Refer servicing to your dealer.

4. Never face the camera towards the sun or any bright or reective light, which may cause smear

on the picture and possible damage to the Image Sensor.

5. Do not remove the serial sticker for the warranty service.

6. Do not expose the camera to rain or other types of liquid.

7. The apparatus must be connected to a mains socket-outlet with a protective earthing connection.

4

1. CAUTIONS

Correct Disposal of This Product

(Waste Electrical & Electronic Equipment)

(Applicable in the European Union and other European countries with separate collection systems)

This marking shown on the product or its literature, indicate that it should not be disposed
with other household wastes at the end of its working life. To prevent possible harm to the
environment or human health from uncontrolled waste disposal, please separate this from
other types of wastes and recycle it responsibly to promote the sustainable reuse of material
resources.

This product should not be mixed with other commercial wastes purchased this product,

or their local government ofce, for details of where and how they can take item for

environmentally safe recycling.

Business users should contact their supplier and check the terms and conditions of the
purchase contract. Household users should contact either the retailer where they for
disposal.

5

2. IMPORTANT SAFETY INSTRUCTION

1) Read these instructions.

2) Keep these instructions.

3) Heed all warnings.

4) Follow all instructions.

5) Do not use this apparatus near water.

6) Clean only with dry cloth.

7) Do not block any ventilation openings. Install in accordance
with the manufacturer’s instructions.

8) Do not install near any heat sources such as radiators, heat registers,

stoves, or other apparatus (including ampliers) that produce heat.

9) Do not defeat the safety purpose of the polarized or grounding-type plug. A
polarized plug has two blades with one wider than the other. A grounding type plug has
two blades and a third grounding prong. The wide blade or the third prong are provided

for your safety. If the provided plug does not t into your outlet, consult an electrician for

replacement of the obsolete outlet.

10) Protect the power cord from being walked on or pinched particularly at plugs,
convenience receptacles, and the point where they exit from the apparatus.

11) Only use attachments/accessories specied by the manufacturer.

12) Use only with the cart, stand, tripod, bracket, or table specied by

the manufacturer, or sold with the apparatus. When a cart is used,
use caution when moving the cart/apparatus combination to
avoid injury from tip-over.

13) Unplug this apparatus during lightning storms or when unused for long

periods of time.

14) Refer all servicing to qualied service personnel. Servicing is required when

the apparatus has been damaged in any way, such as power-supply cord or plug is
damaged, liquid has been spilled or objects have fallen into the apparatus, the apparatus
has been exposed to rain or moisture, does not operate normally, or has been dropped.

6

3. FEATURES

• High Resolution

SONY 1 / 3” 2.1 M Progressive Color CMOS Image Sensor,
1920x1080 30fps

• Support various digital video output

720p60, 720p50, 1080p30, 1080p25

• Video Outputs

Primary HD-SDI (BNC)
Test / Setup TV Out (Test Point-adapter to BNC included),
NTSC / PAL selectable

• OSD menu for setup and configuration

• Provides True Day / Night Capability with Motorized IR Cut Filter

• 20 Long Life IR illuminations for 0 Lux viewing performance and
range to 10m ( 32 feet )

• Lens: Board Lens

• Power Source: DC 12V

• 3-Axis Gimbal

• IP66 Weather Resistant

7

4. EQUIPMENT AND ACCESSORIES

Camera Manual

Template Screws, Set Screw / L-Wrench / Plastic Anchors

Plastic Anchors

Screws

L-Wrench

Option - Remote Control (OSD Key)

Max. 35M

Set Screw

8

5. CAMERA COMPONENT DESCRIPTIONS

Housing Ball

IR LED

Housing Top

Photo Cell

Housing Ball
Bracket

Housing Bottom

9

6. INSTALLATION

Template

70°

140°

70°

Set Screw-M2.5x3L

10

Open

(1ea)

Plastic Anchors

(4ea)

Tapping Screws-4x25L

(4ea)

Close

L-Wrench

6. INSTALLATION

• MONITOR CONNECTION

RCA Jack

(OSD Key Jack)

BNC Female
(2'nd Video)

DC12V IN (Black)

* Option: Remote Control
(OSD Key)

DC12V

Adapter

BNC Female

(HD-SDI Jack)

HD-SDI IN

* Remote Control - Circuit Diagram (Option)

Function

SW1: Menu OSD Menu on / off, Selection.
SW2: Up OSD Menu up.
SW3: Down OSD Menu Down.
SW4: Left OSD Menu Left.
SW5: Right OSD Menu Right.

When you install the camera, please glue up the end of cable to
keep it stable in order to protect the camera from the humidity problems.

11

Monitor

7. DIMENSIONS

Unit(mm)

Ø 93

20-IR LED

Ø 69

63

4-Ø4.5

77

Ø68.5

(The maximum rotation)

12

8. SPECIFICATION

Image Device 2.1Mega Pixel. 3/1" Exmor SONY CMOS
Effective Pixels 1984 (H) x 1105 (V) 30fps
Unit Cell Size(um) 2.8 (H) x 2.8 (V)

Video Output Mode

Minimum Illumination 0 Lux
Video Output HD-SDI / 1.0 Vp-p Composite (75Ω)
IR LED 850nm , 20ea
IR Beam Range Up to 10M ( 32 Feet )
S/N Ratio More than 50dB
Shutter Speed Auto / Manual selectable

Manual Shutter Speed

D-WDR / BLC OFF / BLC / D-WDR
AGC Max. 29 dB
3DNR OFF / LOW / MIDDLE / HIGH
Day & Night True Day & Night with ICR Mechanism
White Balance AUTO / AUTOext / PUSH / MANUAL
Digital Zoom Ratio 1x ~ 20x
Privacy Masking Zone 24, On / Off
Lens Board Lens
OSD Built-in
Power Consumption DC 12V(±10%), Max. 420mA
Weight Approx. 330g
Dimension(mm) Ø93 X 63
Conformity CE, FCC, KC
Temperature / Humidity
(no condensing)

*Specifications and designs are subject to change for improving the

functionality of this product without notice.

HD-SDI: 720p60, 720p50,1080p30, 1080p25

TV Out: NTSC / PAL Selectable

1/30(25), 1/60(50), 1/120(100), 1/240, 1/500,

1/1K, 1/2K, 1/4K, 1/8K, 1/16K, 1/30K, 1/60K

Operation: 14°F~122°F(-10°C~+50°C / 20~80%)

Storage: -4°F~140°F(-20°C~+60°C / 20~90%)

13

9. OSD MANUAL

• Menu structure

Main Sub Menu Sub Menu

BRIGHTNESS 0 ~ 20

SHUTTER

EXPOSURE

BALANCE

DSS OFF, X2, X3, X4, X5, X6, X7, X8
AGC 0 ~ 10
BASE FREQ 60Hz / 50Hz
RESET DATA BACK / DEF.
RETURN BACK / EXIT.

WB MODE

WHITE

SATURATION 0 ~ 20
RESET DATE BACK / DEF.
RETURN BACK / EXIT.
MODE OFF, BLC, D-WDR
BLC OSD OFF ~ ON
BLC POS-X 0 ~ 20
BLC POS-Y 0 ~ 20

D-WDR /

BLC

BLC SIZE-X 0 ~ 20
BLC SIZE-Y 0 ~ 20
RESET DATA BACK / DEF.
RETURN BACK / EXIT.

DNR OFF, LOW, MIDDLE, HIGH

LEVEL

MANUAL /
AUTO

RETURN BACK / EXIT

COLORTEMP. LOW / MIDDLE / HIGH

AUTO

R-GAIN 0 ~ 20

/AUTOext
/PUSH

B-GAIN 0 ~ 20

/MANUAL

RETURN BACK / EXIT

1/30(25), 1/60(50), 1/120(100), 1/240, 1/500,
1/1K, 1/2K, 1/4K, 1/8K, 1/16K, 1/30K, 1/60K.

14

9. OSD MANUAL

Main Sub Menu Sub Menu

SHARPNESS 0 ~ 20
GAMMA 0 ~ 4
FLIP OFF / H FLIP / V FLIP / HV FLIP
LENS SHADING OFF / ON

IMAGE

DZOOM 1X / 2X / 4X / 6X / 8X / 10X / 12X / 14X / 16X / 18X / 20X
RESET DATA BACK / DEF
RETURN BACK / EXIT

PRIVACY OFF/ ON

SPECIAL

HLMASK OFF/ ON

PATTERN OFF / 0 / 1
RESET DATA BACK / DEF.
RETURN BACK / EXIT.
SDI FORMAT 1080P / 720P
SDI FPS 30(60) / 25(50)

CVBS FORMAT

APPLY OK / ON

SYSTEM

SYSTEM INFO.

REBOOT
RETURN BACK / EXIT

NTSC /
PAL

ZONE NO 0 ~ 23
ZONE OP OFF/ ON
X-POS 0 ~ 60
Y-POS 0 ~ 40
X-SIZ 0 ~ 40
Y-SIZ 0 ~ 40

COLOR

TRANS 0 ~ 4
RESET DATA BACK / DEF.
RETURN BACK / EXIT.
LEVEL 0 ~ 20

COLOR

RESET DATA BACK / DEF.
RETURN BACK / EXIT.

CVBS VIEW CROP / FULL
RETURN BACK / EXIT.

S/W VERSION
SET VERSION
RETURN BACK / EXIT.

BLK, WHI, YEL, CYN, GRN,
MAG, RED, BLU

BLK, WHI, YEL, CYN, GRN,
MAG, RED, BLU

15

9. OSD MANUAL

• Function Description

0. SETUP

- EXPOSURE : Go sub menu for camera exposure control.

- WHITE ALANCE : Go sub menu for camera white balance control.

- D-WDR / BLC : Go sub menu for camera D-WDR or BLC action.

- DNR : Control noise reduction setting.

- IMAGE : Go sub menu for adjust image functions.

- SPECIAL : Go sub menu for special feature control.

- SYSTEM : Go sub menu for system control & information.

- Reset Data All : Reset camera’s all feature data to default value.

1. EXPOSURE

- BRIGHTNESS : Adjust image brightness value.

- SHUTTER : Select shutter speed control type.

• LEVEL : Adjust shutter speed at manual shutter mode.

- DSS : Adjust digital slow shutter control level.

- AGC : Adjust max gain level for brightness control.

- BASE FREQ : Select basic control frequency for control camera feature.

2. WHITE BALANCE

- WB MODE : Select white balance control mode.
> AUTO : Full auto control mode in color temperature rage 2300K~10000K.
> AUTOext : Extended auto mode for special illumination.
> PUSH : Enable fix the control setting for specific environment.

> MANUAL : Enable WB control setting by user’s intention.

• COLOR TEMP. : Select color temperature range for WB control at manual mode.

• R-GAIN

• B-GAIN

- SATURATION : Adjust color saturation level.

Push & release, for fix WB control setting.

: Adjust red color gain for WB control at maual mode.
: Adjust blue color gain for WB control at manual mode.

16

9. OSD MANUAL

3. D-WDR / BLC

- MODE : Select D-WDR / BLC mode.
> BLC : Act in Backlight compensation mode.
> D-WDR : Digital wide dynamic range control.

- BLC OSD : Display BLC control zone in screen.

- BLC POS-X : Select BLC control zone vertical position.

- BLC POS-Y : Select BLC control zone horizontal position.

- BLC SIZ-X : Select BLC control zone vertical size.

- BLC SIZ-Y : Select BLC control zone horizontal size.

4. DNR: Reduce image’s noise

5. IMAGE

- SHARPNESS : Adjust image sharpness level.

- GAMMA : Gamma Curve Select.

- FLIP : Vertical & Horizontal flip setting.

- LENS SHADING : Enable lens shading compensation.

- DZOOM : Select digital zoom magnification.

6. SPECIAL

- PRIVACY : Setting for protect private area in image using mask setting.

• ZONE NO. : Select private mask zone number.

• ZONE OP. : Select zone mask display on/off.

• X-POS : Select zone horizontal position.

• Y-POS : Select zone vertical position.

• X-SIZ : Select zone horizontal size.

• Y-SIZ : Select zone vertical size.

• COLOR : Select mask color

• TRANS. : Select mask transparency level.

- HLMASK : Mask image high light area.

• LEVEL : Select high light level.

• COLOR : Select mask color.

- PATTERN : Color bar display Select.

17

9. OSD MANUAL

7. SYSTEM

- SDI FORMAT : 1080P / 720P

- SDI FPS : 30 or 25 fps in 1080p mode.

- CVBS FORMAT : NTSC / PAL

• CVBS VIEW : CVBS out video angle setting.
CROP

◦

FULL

◦

- APPLY : Apply all video setting changed at once.

- SYSTEM INFO.

• S/W VERSION : Camera’s basic software version.

• SET VERSION : Camera’s feature control setting version.

60 or 50 fps in 720p mode.

: Cut the scene outside area for keep image aspect ratio.
: Fill the full angle scene into image with
H-V size & ratio change.

Use the Set button to apply.

18