M141-HDX222-001
HD CCTV
Digital Video Camera
OPERATION MANUAL
Thank you for choosing our high quality camera. Before attempting to connect operate this
unit, please read and follow these instructions.
CAUTION
These servicing instructions are for use by qualied service personnel only.
To reduce the risk of electric shock do not perform any servicing other than that
contained in the operating instructions unless you are qualied to do so.
Use Class 2 Power Supply Only
2
CONTENTS
1. CAUTIONS
2. IMPORTANT SAFETY INSTRUCTIONS
3. FEATURES
4. EQUIPMENT AND ACCESSORIES
5. CAMERA COMPONENT DESCRIPTIONS
6. INSTALLATION
7. DIMENSIONS
8. SPECIFICATIONS
9. OSD MANUAL
3
1. CAUTIONS
This device complies with Part 15 of the FCC Rules.
Operation is subject to the following two conditions:
1. This device may not cause harmful interference.
2. This device must accept any interference received, including interference
that may cause undesired operation.
Note
This equipment has been tested and found to comply with the limits for a Class A digital
device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable
protection against harmful interference when the equipment is operated in a commercial
environment. This equipment generates, uses, and can radiate radio frequency energy
and, if not installed and used in accordance with the instruction manual, may cause harmful
interference to radio communications. Operation of this equipment in a residential area is
likely to cause harmful interference in which case the user will be required to correct the
interference at his own expense.
WARNING
This is a class A product. In a domestic environment this product may cause radio interference
in which case the user may be required to take adequate measures.
Caution
Any changes or modications in construction of this devices which are not expressly approved
by the party responsible for compliance could void the user’s authority to operate the
equipment.
1. A regulated DC12V 500mA power supply is recommended for use with this camera for the best
picture and the most stable operation. An unregulated power supply can cause damage to the
camera. When an unregulated power supply is applied, the product warranty will be void.
2. It is recommended that the camera be used with a monitor that has a CCTV quality 75Ω video
impedance level. If your monitor is switched to high impedance then please adjust accordingly.
3. Do not attempt to disassemble the camera to gain access to the internal components.
Refer servicing to your dealer.
4. Never face the camera towards the sun or any bright or reective light, which may cause smears
on the picture and possible damage to the Image Sensor.
5. Do not remove the serial sticker for the warranty service.
6. Do not expose the camera to rain or other types of liquid.
7. The apparatus must be connected to a main socket-outlet with a protective earth connection.
4
1. CAUTIONS
(Waste Electrical & Electronic Equipment)
WEEE
This marking shown on the product or its literature, indicates that it should not be disposed
with other household wastes at the end of its working life.
To prevent possible harm to the environment or human health from uncontrolled waste
disposal, please separate this from other types of wastes and recycle it responsibly to
promote the sustainable reuse of material resources. Household users should contact either
the retailer where they purchased this product, or their local government ofce, for details of
where and how they can take item for environmentally safe recycling.
Business users should contact their supplier and check the terms and conditions of
the purchase contract.
This product should not be mixed with other commercial wastes for disposal.
CAUTION
RISK OF ELECTRIC SHOCK DO NOT OPEN
CAUTION:
TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE
COVER (OR BACK). NO USER SERVICEABLE PARTS INSIDE. REFER
SERVICING TO QUALIFIED SERVICE PERSONNEL
This symbol is intended to alert the user to the presence of un-insulated
“dangerous voltage” within the product’s enclosure that may be of sufcient
magnitude to constitute a risk of electric shock.
This symbol is intended to alert the user to the presence of important operating
and maintenance (servicing) instructions i n the lit erature accompanyi ng the
appliance.
5
2. IMPORTANT SAFETY INSTRUCTIONS
1) Read these instructions.
2) Keep these instructions.
3) Heed all warnings.
4) Follow all instructions.
5) Do not use this apparatus near water.
6) Clean only with dry cloth.
7) Do not block any ventilation openings. Install in accordance
with the manufacturer’s instructions.
8) Do not install near any heat sources such as radiators, heat registers,
stoves, or other apparatus (including ampliers) that produce heat.
9) Do not defeat the safety purpose of the polarized or grounding-type plug. A
polarized plug has two blades with one wider than the other. A grounding type plug has
two blades and a third grounding prong. The wide blade or the third prong are provided
for your safety. If the provided plug does not t into your outlet, consult an electrician for
replacement of the obsolete outlet.
10) Protect the power cord from being walked on or pinched particularly at plugs,
convenience receptacles, and the point where they exit from the apparatus.
11) Only use attachments/accessories specied by the manufacturer.
12) Use only with the cart, stand, tripod, bracket, or table specied by
the manufacturer, or sold with the apparatus. When a cart is used,
use caution when moving the cart/apparatus combination to
avoid injury from tip-over.
13) Unplug this apparatus during lightning storms or when unused for long
periods of time.
14) Refer all servicing to qualied service personnel. Servicing is required when
the apparatus has been damaged in any way, such as power-supply cord or plug is
damaged, liquid has been spilled or objects have fallen into the apparatus, the apparatus
has been exposed to rain or moisture, does not operate normally, or has been dropped.
6
3. FEATURES
• High Resolution
SONY 1/3” 2.1M/P Progressive Color CMOS Image Sensor,
1920x1080 30fps
• Support various digital video output
720p60, 720p50, 1080p30, 1080p25
• Video Outputs
Primary HD-SDI (BNC)
Test/Setup TV Out (Test Point-adapter to BNC included), NTSC/PAL selectable
• OSD menu for setup and configuration
• Lens Control
DC Iris
• Power Source
DC 12V / AC 24V ( Dual Power Type )
DC 12V ( DC Power Type )
7
4. EQUIPMENT AND ACCESSORIES
HD CCTV
Digital Video Camera
Auto Iris Lens
Connection Plug
C-mount Adaptor Ring
Operation Manual
NOTE
*
PLEASE REMOVE PROTECTION FILM
8
+ -
5. CAMERA COMPONENT DESCRIPTIONS
• FRONT
TRIPOD MOUNTING HOLE(1/4"-20 UNC)
C-MOUNT ADAPTOR RING
MOUNT COVER
CS-MOUNT ADAPTOR RING
CS-MOUNT ADAPTOR RING FIXING SCREW(2EA)
TRIPOD MOUNTING HOLE(1/4"-20 UNC)
AUTO
IRIS JACK
9
5. CAMERA COMPONENT DESCRIPTIONS
• BACK
➊ ➋ ➎ ➐
➍
➌
+ -
➓
DC12V GND
HD SDI
OUTPUT
➊ ➋ ➎ ➐
➍
➑
➌
➏
➒
➓
MENU/SETMENU/SET
DC12V/AC24V
VIDEOVIDEO
OFF/ONOFF/ON
POWERPOWER
HD SDI
OUTPUT
VIDEOVIDEO
➑
➏
➒
DC12V
①. MENU BUTTON
②. UP BUTTON
③. DOWN BUTTON
④. LEFT BUTTON
⑤. RIGHT BUTTON
⑥. POWER LED
(The LED turns on when power is supplied)
⑦. VIDEO OFF/ON SWITCH
⑧. HD SDI OUTPUT JACK
⑨. VIDEO OUT JACK
(Used to connect an external video monitor in jack)
⑩.POWER TERMINAL
(Used to connect an DC12V power source)
(Options : AC24V / DC12V)
AC24V / DC12V
10
6. INSTALLATION
• LENS CONNECTION
Mega Pixel Lenses are sold separately. Lenses such as an auto iris lens,
CS-Mount lens and C-Mount lens can be used (adapter included for C-Mount Lens).
NOTE
• Please keep the lens clean.
• Any foreign objects and Finger marks on the lens can cause
inferior image quality in low light level conditions
When using an auto iris lens
1. Please peel off about 8mm
of the outer skin of the auto iris lens cable.
2. Please peel off about 2mm of the outer skin
of the insulated conductor inside the lens cable.
.
11
6. INSTALLATION
3. Please remove the cover of the auto iris lens connection plug and
solder the lens cable to the connector pin in the plug.
* PIN ASSIGNMENT OF THE LENS CONNECTOR
1) Video auto iris lens
Pin 1: Power source(DC 12V)
Pin 3: Video signal
Pin 4: Shield, GND(Ground)
2) DC auto iris lens
Pin 1: DAMP-(CTL-)
Pin 2: DAMP+(CLT+)
Pin 3: DRV+
Pin 4: DRV-(GND)
4. Please replace the auto iris lens connection plug cover and take off the sensor
protection cap and then attach the auto iris lens to the camera by screwing it in
clockwise.
12
6. INSTALLATION
5. Please insert the connection plug from the auto iris lens cable into the auto
lens connector, which is located on the side of the camera.
* NOTE
Use the lens under the specification as shown.
Otherwise the lens can damage the camera or
abnormal fixing may result.
C-mount lens : 10 mm or less
CS-mount lens : 5 mm or less
13
6. INSTALLATION
Installation of C-Mount Lens
Installation of CS-Mount Lens
C-MOUNT ADAPTOR RING
CS-MOUNT ADAPTOR RING
CS-MOUNT ADAPTOR RING
14
6. INSTALLATION
• MONITOR CONNECTION
- DC12V
VIDEO
HD SDI
OUTPUT
OFF/ON
MENU/SET
POWER
+ -
DC12V GND
- DC12V/AC24V
MENU/SET
DC12V/AC24V
VIDEO
DC12V REGULATED
POWER SUPPLY
VIDEO
HD SDI
OUTPUT
OFF/ON
POWER
VIDEO
DC12V / AC24V REGULATED
POWER SUPPLY
HD SDI OUTPUT
BNC FEMALE
VIDEO OUTPUT
HD SDI OUTPUT
BNC FEMALE
VIDEO OUTPUT
SDI
RECEIVER
DISPLAY
DEVICE
HD SDI INPUT
TV
MONITOR
VIDEO INPUT
SDI
RECEIVER
DISPLAY
DEVICE
HD SDI INPUT
TV
MONITOR
VIDEO INPUT
CAUTIONS
When you output Video
15
WDR function does not work
7. DIMENSIONS
Unit(mm)
86.1(C-MOUNT)
81.1(CS-MOUNT)
58
TRIPOD MOUNTING HOLE
(1/4"-20 UNC, Depth 5)
58
TRIPOD MOUNTING HOLE
(1/4"-20 UNC, Depth 5)
75.5(C-MOUNT)
70.5(CS-MOUNT)
16
8. SPECIFICATION
Image Device SONY 1/3” 2.1M/P Progressive Color CMOS Image Sensor
Effective Pixels 1984 (H) x 1105 (V) 30fps
Unit cell size 2.8um (H) x 2.8um (V)
Video Output Mode
Minimum Illumination 0.1 Lux
S/N Ratio More than 50dB
Shutter Speed Auto / Manual selectable
Manual Shutter Speed
Controllable Max Gain 29 dB
White Balance AUTO / AUTOext / PUSH / MANUAL
Lens Control DC Iris
OSD Menu Yes
Power
Consumption
Weight DC12V: 175g, DUAL: 200g
Dimension 58(W) x 58(H) x 70.5(D)
Conformity CE, FCC, KC
Temperature / Humidity
(no condensing)
DC DC12V(±10%), Max. 200mA
DUAL
Specifications and designs are subject to change for improving the
HD-SDI: 720p60, 720p50, 1080p30, 1080p25
TV Out: NTSC / PAL selectable
1/30(25), 1/60(50), 1/120(100), 1/240, 1/500,
1/1K, 1/2K, 1/4K, 1/8K, 1/16K, 1/30K, 1/60K
DC12V(±10%), Max. 270mA
AC24V(±10%), Max. 3.6W
Operation: 14°F~122°F(-10°C~+50°C / 20~80%)
Storage: -4°F~158°F(-20°C~+60°C / 20~95%)
functionality of this product without notice.
17
9. OSD MANUAL
• Menu structure
Main Sub Menu Sub Menu
BRIGHTNESS 0 ~ 20
AE MODE NORMAL AE / INDOOR
LENS(IRIS) MANUAL / AUTO
EXPOSURE
BALANCE
WDR / BLC
SHUTTER
DSS OFF, X2, X3, X4, X5, X6, X7, X8
AGC 0 ~ 10
BASE FREQ 60Hz / 50Hz
RESET DATA BACK / DEF.
RETURN BACK / EXIT.
WB MODE
WHITE
SATURATION 0 ~ 20
RESET DATE BACK / DEF.
RETURN BACK / EXIT.
MODE OFF, WDR, BLC, D-WDR
WDR WGT 0 ~ 4
BLC OSD OFF ~ ON
BLC POS-X 0 ~ 20
BLC POS-Y 0 ~ 20
BLC SIZE-X 0 ~ 20
BLC SIZE-Y 0 ~ 20
RESET DATA BACK / DEF.
RETURN BACK / EXIT.
DNR OFF, LOW, MIDDLE, HIGH
DAY &
NIGHT
LEVEL
MANUAL /
AUTO
RETURN BACK / EXIT
COLORTEMP. LOW / MIDDLE / HIGH
AUTO
R-GAIN 0 ~ 20
/AUTOext
/PUSH
B-GAIN 0 ~ 20
/MANUAL
RETURN BACK / EXIT
D&N DETECT AGC
DELAY 1sec, 3, 5, 10, 15, 20, 25, 30, 40, 50, 60sec
COLOR/
D->N LEVEL 3 ~ 20
B&W/
N->D LEVEL 0 ~ 16
AUTO
RESET DATA BACK / DEF.
RETURN BACK / EXIT.
1/30(25), 1/60(50), 1/120(100), 1/240, 1/500,
1/1K, 1/2K, 1/4K, 1/8K, 1/16K, 1/30K, 1/60K.
18
9. OSD MANUAL
Main Sub Menu Sub Menu
SHARPNESS 0 ~ 20
GAMMA 0 ~ 4
FLIP OFF, H FLIP, V FLIP, HV FLIP
IMAGE
LENS SHADING OFF, ON
DZOOM 1x, 2x, 4x, 6x, 8x, 10x, 12x, 14x, 16x, 18x, 20x
RESET DATA BACK / DEF.
RETURN BACK / EXIT.
PRIVACY OFF / ON
SPECIAL
HLMASK OFF / ON
PATTERN OFF / 0 / 1
RESET DATA BACK / DEF.
RETURN BACK / EXIT.
SDI FORMAT 1080P / 720P
SDI FPS 30(60) / 25(50)
CVBS FORMAT
APPLY OK / ON
SYSTEM
SYSTEM INFO.
REBOOT
RETURN BACK / EXIT.
ZONE NO 0 ~ 23
ZONE OP OFF / ON
X-POS 0 ~ 60
Y-POS 0 ~ 40
X-SIZ 0 ~ 40
Y-SIZ 0 ~ 40
COLOR BLK, WHT, YEL, CYN, GRN, MAG, RED, BLU
TRANS. 0 ~ 4
RESET DATA BACK / DEF.
RETURN BACK / EXIT.
LEVEL 0 ~ 20
COLOR BLK, WHT, YEL, CYN, GRN, MAG, RED, BLU
RESET DATA BACK / DEF.
RETURN BACK / EXIT.
CVBS OUT AUTO / OFF / ON(WDR OFF)
NTSC /
CVBS VIEW CROP / FULL
PAL
RETURN BACK / EXIT.
S/W VERSION
SET VERSION
RETURN BACK / EXIT.
19
9. OSD MANUAL
• Function Description
0. SETUP
- EXPOSURE : Go sub menu for camera exposure control.
- WHITE ALANCE : Go sub menu for camera white balance control.
- WDR/BLC : Go sub menu for camera WDR or BLC action.
- DNR : Control noise reduction setting.
- DAY & NIGHT : Go sub menu for camera day & night control.
- IMAGE : Go sub menu for adjust image functions.
- SPECIAL : Go sub menu for special feature control.
- SYSTEM : Go sub menu for system control & information.
- RESET DATA ALL : Reset camera’s all feature data to default value.
1. EXPOSURE
- BRIGHTNESS : Adjust image brightness value.
- AE MODE : Adjust AE control mode.
- LENS(IRIS) : Select lens iris control type.
- SHUTTER : Select shutter speed control type.
• LEVEL : Adjust shutter speed at manual shutter mode.
- DSS : Adjust digital slow shutter control level.
- AGC : Adjust max gain level for brightness control.
- BASE FREQ : Select basic control frequency for control camera feature.
2. WHITE BALANCE
- WB MODE : Select white balance control mode.
• AUTO : Full auto control mode in color temperature rage 2300K~10000K.
• AUTOext : Extended auto mode for special illumination.
• PUSH : Enable fix the control setting for specific environment.
• MANUAL : Enable WB control setting by user’s intention.
COLOR TEMP. : Select color temperature range for WB control at manual mode.
◦
R-GAIN : Adjust red color gain for WB control at maual mode.
◦
B-GAIN : Adjust blue color gain for WB control at manual mode.
◦
- SATURATION : Adjust color saturation level.
Push & release, for fix WB control setting.
20
9. OSD MANUAL
3. WDR/BLC
- MODE : Select WDR / BLC mode.
• WDR : Act in wdie dynamic rage mode. Controled video frame rate in 1/2.
• BLC : Act in Backlight compensation mode.
• D-WDR : Digital wide dynamic range control.
- WDR WGT : WDR weight control level settig at WDR mode.
- BLC OSD : Display BLC control zone in screen.
- BLC POS-X : Select BLC control zone vertical position.
- BLC POS-Y : Select BLC control zone horizontal position.
- BLC SIZ-X : Select BLC control zone vertical size.
- BLC SIZ-Y : Select BLC control zone horizontal size.
4. DNR: Reduce image’s noise
5. DAY & NIGHT
- MODE : Select TDN(True Day & Night control) mode.
• AUTO : Camera controlled automatically to decide day or night environment
• COLOR : Fix to mode at day environment setting.
• B&W : Fix to mode at night environment setting.
■
D/N DETECT : Fixed selection to AGC for TDN auto control.
■
DELAY : Delay time for change day or night mode at auto mode.
■
D->N LEVEL : Threshold level for change Day to Night mode.
■
N->D LEVEL : Threshold level for change Night to Day mode.
6. IMAGE
- SHARPNESS : Adjust image sharpness level.
- GAMMA : Gamma curve select.
- FLIP : Vertical & Horizontal flip setting.
- LENS SHADING : Enable lens shading compensation.
- DZOOM : Select digital zoom magnification.
using AGC calculation data or input level data from CDS sense.
Make video image act in color.
Make video image act in B/W.
21
9. OSD MANUAL
7. SPECIAL
- PRIVACY : Setting for protect private area in image using mask setting.
• ZONE NO. : Select private mask zone number.
• ZONE OP. : Select zone mask display on/off.
• X-POS : Select zone horizontal position.
• Y-POS : Select zone vertical position.
• X-SIZ : Select zone horizontal size.
• Y-SIZ : Select zone vertical size.
• COLOR : Select mask color
• TRANS. : Select mask transparency level.
- HLMASK : Mask image high light area.
• LEVEL : Select high light level.
• COLOR : Select mask color.
- PATTERN : Color bar display select.
8. SYSTEM
- SDI FORMAT : 1080P / 720P
- SDI FPS : 30 or 25 fps in 1080p mode.
- CVBS FORMAT : NTSC / PAL
• CVBS OUT : Select mode for CVBS out action.
ON, OFF : Enable or Disable CVBS out data.
◦
AUTO : Check automatically CVBS video cable connection.
◦
• CVBS VIEW : CVBS out video angle setting.
CROP : Cut the scene outside area for keep image aspect ratio.
◦
FULL : Fill the full angle scene into image with
◦
- APPLY : Apply all video angle setting. Use the set button to apply.
- SYSTEM INFO.
• S/W VERSION : Camera’s basic software version.
• SET VERSION : Camera’s feature control setting version.
60 or 50 fps in 720p mode.
If connected, CVBS out data is enable and WDR mode
is setted off automatically.
H-V size & ratio change.
22
Loading...