KT&C KPC-HDX210 Operation Manual

HD CCTV
Digital Video Camera

OPERATION MANUAL

Thank you for choosing our high quality camera.
Before attempting to connect or operate, please read and follow
these instructions.

M133-HDX210-001

These servicing instructions are for use by qualied service personnel only.
To reduce the risk of electric shock do not perform any servicing other than
that contained in the operating instructions unless you are qualied to do so.

Use Class 2 Power Supply Only

CAUTION

2

CONTENTS

1. CAUTIONS

2. IMPORTANT SAFETY INSTRUCTION

3. FEATURES

4. EQUIPMENT AND ACCESSORIES

5. CAMERA COMPONENT DESCRIPTIONS

6. INSTALLATION

7. DIMENSIONS

8. SPECIFICATION

9. OSD MANUAL

3

4

1. CAUTIONS

This device complies with Part 15 of the FCC Rules.
Operation is subject to the following two conditions;

1. This device may not cause harmful interference.

2. This device must accept any interference received,
including interference that may cause undesired operation.

Note

This equipment has been tested and found to comply with the limits for a Class A digital
device, pursuant to part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference when the equipment is operated
in a commercial environment. This equipment generates, uses, and can radiate radio
frequency energy and, if not installed and used in accordance with the instruction
manual, may cause harmful interference to radio communications. Operation of this
equipment in a residential area is likely to cause harmful interference in which case the
user will be required to correct the interference at his own expense.”

WARNING

This is a class A product. In a domestic environment this product may cause radio
interference in which case the user may be required to take adequate measures.

Caution

Any changes or modications in construction of this devices which are not expressly

approved by the party responsible for compliance could void the user’s authority to
operate the equipment.

1. A regulated DC12V 1A power supply is recommended for use with this camera
for the best picture and the most stable operation.
An unregulated power supply can cause damage to the camera.

When unregulated power supply is applied, product warranty will be out of subject.

2. It is recommended that the camera is used with a monitor that has a CCTV quality
75 video impedance level.
If your monitor is switched to high impedance then please adjust accordingly.

3. Do not attempt to disassemble the camera to gain access to the internal components.
Refer servicing to your dealer.

4. Never face the camera towards the sun or any bright or reective light, which may

cause smear on the picture and possible damage to the CCD.

5. Do not remove the serial sticker for the warranty service.

6. Do not expose the camera to rain or other types of liquid.

7. The apparatus must be connected to a mains socket-outlet with a protective earthing
connection.

CAUTIONS

1. CAUTIONS

5

Correct Disposal of This Product

(Waste Electrical & Electronic Equipment)

(Applicable in the European Union and other European countries with
separate collection systems)

This marking shown on the product or its literature, indicate that it should not
be disposed with other household wastes at the end of its working life. To
prevent possible harm to the environment or human health from uncontrolled
waste disposal, please separate this from other types of wastes and recycle it
responsibly to promote the sustainable reuse of material resources.

This product should not be mixed with other commercial wastes purchased this

product, or their local government ofce, for details of where and how they can

take item for environmentally safe recycling.
Business users should contact their supplier and check the terms and

conditions of the purchase contract.
Household users should contact either the retailer where they for disposal.

2. IMPORTANT SAFETY INSTRUCTION

1) Read these instructions.

2) Keep these instructions.

3) Heed all warnings.

4) Follow all instructions.

5) Do not use this apparatus near water.

6) Clean only with dry cloth.

7) Do not block any ventilation openings. Install in accordance
with the manufacturer’s instructions.

8) Do not install near any heat sources such as radiators, heat registers,

stoves, or other apparatus (including ampliers) that produce heat.

9) Do not defeat the safety purpose of the polarized or grounding-type plug. A
polarized plug has two blades with one wider than the other. A grounding type
plug has two blades and a third grounding prong. The wide blade or the third

prong are provided for your safety. If the provided plug does not t into your

outlet, consult an electrician for replacement of the obsolete outlet.

10) Protect the power cord from being walked on or pinched particularly at plugs,
convenience receptacles, and the point where they exit from the apparatus.

11) Only use attachments/accessories specied by the manufacturer.

12) Use only with the cart, stand, tripod, bracket, or table specied by

the manufacturer, or sold with the apparatus. When a cart is used,
use caution when moving the cart/apparatus combination to
avoid injury from tip-over.

13) Unplug this apparatus during lightning storms or when unused for long

periods of time.

14) Refer all servicing to qualied service personnel. Servicing is required when

the apparatus has been damaged in any way, such as power-supply cord
or plug is damaged, liquid has been spilled or objects have fallen into the
apparatus, the apparatus has been exposed to rain or moisture, does not
operate normally, or has been dropped.

6

3. FEATURES

• High Resolution.

1/3” SONY Progressive Color CMOS Image Sensor,
1920 x 1080 60fps

• Support various digital video output.

720p30, 720p60, 720p25, 720p50,
1080i60, 1080i50,
1080p30, 1080p25

• Video Output.

Primary HD-SDI (BNC)
Test / Setup TV Out (BNC), NTSC / PAL selectable.

• Support RS485 Communucation Protocol for

Camera Configuration Remote Control.

• OSD menu for setup and configuration.

• Lens Control.

Manual Iris,
DC Iris (or Video Iris : factory selectable).

• Provides True Day/Night Capability with Motorized IR Cut Filter.

• Accepts CS Mount Lenses

Adapter included for C-Mount Lens.

• Power Source

DC 12V / AC 24V

7

4. EQUIPMENT AND ACCESSORIES

HD CCTV

Digital Video Camera

AUTO IRIS LENS

CONNECTION PLUG

C-MOUNT ADAPTOR RING

OPERATION MANUAL

TERMINAL BLOCK

8

*

NOTE

PLEASE REMOVE PROTECTION FILM

HDcctv 1.0

OUTPUT

AC 24V

DC 12V

5. CAMERA COMPONENT DESCRIPTIONS

• FRONT

9

TRIPOD MOUNTING HOLE(1/4"-20 UNC)

AUTO IRIS JACK

MOUNT COVER

C-MOUNT
ADAPTOR RING
(Optional use for C-Mount lens only)

TRIPOD MOUNTING HOLE(1/4"-20 UNC)

BACK FOCUS CONTROL LEVER

5. CAMERA COMPONENT DESCRIPTIONS

• BACK

①. MENU SET BUTTON
MENU NAVIGATION BUTTONS
②. UP BUTTON
③. DOWN BUTTON
④. LEFT BUTTON
⑤. RIGHT BUTTON
⑥. POWER LED
⑦. SDI OUT BNC
⑧. VIDEO OUT BNC
⑨. MIC IN JACK
⑩. AUDIO OUT JACK (TBD)
⑪. TERMINAL (POWER, RS-485, Digital Input/Output)

10

① ②

③

④

⑤

⑥

⑦

⑧

⑨⑩

⑪

HDcctv 1.0

OUTPUT

AC 24V
DC 12V

AC 24V

DC 12V

11

6. INSTALLATION

• LENS CONNECTION

Mega Pixel Lenses are sold separately. Lenses such as an auto iris lens,
CS-Mount lens and C-Mount lens can be used (adapter included for C-Mount Lens).

NOTE

• Please keep the lens clean.

• Any foreign objects and Finger marks on the lens can cause

inferior image quality in low light level conditions

.

When using an auto iris lens

1. Please peel off about 8mm of the outer skin of the auto iris lens cable.

2. Please peel off about 2mm of the outer skin of the insulated conductor

inside the lens cable.

12

6. INSTALLATION

3. Please remove the cover of the auto iris lens connection plug and

solder the lens cable to the connector pin in the plug.

* PIN ASSIGNMENT OF THE LENS CONNECTOR

1) Video auto iris lens
Pin 1: Power source(DC 12V)
Pin 2: N.C(Not used)
Pin 3: Video signal
Pin 4: Shield, GND(Ground)

2) DC auto iris lens
Pin 1: DAMP-(CTL-)
Pin 2: DAMP+(CLT+)
Pin 3: DRV+
Pin 4: DRV-(GND)

4. Please replace the auto iris lens connection plug cover and take off the sensor

protection cap and then attach the auto iris lens to the camera by screwing it in
clockwise.

6. INSTALLATION

5. Please insert the connection plug from the auto iris lens cable into the auto

lens connector, which is located on the side of the camera.

13

C-mount lens : 10mm or less
CS-mount lens : 5mm or less

*NOTE

When using a CS-Mount Lens, you can attach it directly to camera.
If using a C-Mount Lens, you must attach the ring spacer provided,
otherwise if will crack the image sensor.

6. INSTALLATION

Installation of C-Mount Lens

Installation of CS-Mount Lens

14

C-MOUNT ADAPTOR RING

15

6. INSTALLATION

• MONITOR CONNECTION

DC12V / AC24V REGULATED
POWER SUPPLY

BNC FEMALE
VIDEO

To VIDEO IN

To HD - SDI IN

HDcctv DVR
or Other
HDcctv Signal
Equipment

Hand - Held
Test Monitor

HDcctv 1.0

OUTPUT

AC 24V
DC 12V

16

7. DIMENSIONS

Unit(mm)

143.5(C-Mount)

138.5(CS-Mount)

AUTO IRIS JACK

MOUNTING HOLE

C-MOUNT ADAPTOR RING

(Optional use for C-Mount lens only)

72.5

66

MOUNTING HOLE

(1/4"-20 UNC, Depth 5)

8. SPECIFICATION

Image Device SONY 1/3” Progressive Color CMOS Image Sensor

Effective Pixels 2096(H) x 1561(V) 60fps

Unit cell size 2.5um(H) x 2.5um(V)

Video output mode

HD-SDI : 720p30, 720p60, 720p25, 720p50,

1080i60, 1080i50,
1080p30, 1080p25

TV Out : NTSC / PAL selectable

Minimum illumination 1.0 Lux

S/N Ratio Max 50dB

Shutter speed Auto / Manual selectable

Min. Exposure Time 1/10000 sec

Flickerless Off / 60Hz(50Hz) selectable

True Day/Night

IR Cut / Pass Filter change

White Balance

ATW / Manual / Specific Color / Push

BLC On / Off (by OSD)

WDR On / Off (by OSD)

Lens Control Manual Iris, DC Iris (or Video Iris : factory setting only)

Privacy Mask On / Off selectable & Position controlable each 15 Zone

OSD Menu Yes

Power
Consumption

DC 12V (±10%) Max. 500mA

AC 24V (±10%) Max. 6W

Dimension (W x H x D) 72.5

mm

x 66mm x 138.5mm

Weight 450g

Lens Mount CS / C-mount

Conformity CE, FCC, KC, HDcctv Alliance Base-Line Compliance

Temperature/Humidity
(non-condensing)

Operation : -10~50 / 20~80%

Storage : -20~70 / 20~95%

Specications and designs are subject to change for improving the functionality of this product without notice.

17

18

9. OSD MANUAL

• Menu structure

- Main Menu

- VIDEO OUT Menu

SYSTEM

VIDEO OUT

LENS

EXPOSURE

WHITE BALANCE

DAY / NIGHT

IMAGE

VIDEO SDI RESOLUTION

SDI FRAME RATE

CDBS FORMAT

VIDEO APPLY

30HZ / 25HZ

NTSC / PAL

30HZ / 25HZ / 60HZ / 50HZ

60HZ / 50HZ

1080P / 1080I / 720P

1080P

720P

1080i

9. OSD MANUAL

- LENS Menu

- EXPOSURE Menuv

19

LENS LENS TYPE

IRIS VOLUME 0 ~ 50

DC IRIS (VIDEO IRIS) / MANUAL IRIS

EXPOSURE SHUTTER

AGC

FLICKERLESS

BRIGHTNESS

BLC

WDR

0 ~ 186

OFF / 50HZ / 60HZ

0 ~ 255

ON / OFF

ON / OFF

SHUTTER MODE

AE PRIORITY

USER MODE

GAIN LEVEL

SHUTTER

LEVEL

1 ~ 4

1 ~ 150

1 ~ 160

GAIN LEVEL

SHUTTER LEVEL 1 ~ 160

NORMAL AE / AE HOLD / MANUAL

NORMAL / GAIN / SHUTTER

0 DB / 1.2 DB / 3.31 DB

5.12 DB / 6.92 DB / 9.33 DB /

11.14 DB / 12.94 DB /

15.34 DB / 17.16 DB /

18.96 DB / 21.37 DB /

23.18 DB / 24 DB /

27.09 DB / 29.2 DB

NORMAL AE

NORMAL

GAIN

SHUTTER

9. OSD MANUAL

- WHITE BALANCE Menu

- DAY / NIGHT Menu

WHITE BALANCE WB MODE

R GAIN

ATW MODE

0 ~ 255

INDOOR / OUTDOOR

B GAIN

TARGET TEMP

0 ~ 255

1500K / 1567K / 1641K / 1721K /
1810K / 1909K / 2019K / 2143K /
2283K / 2442K / 2625K / 2838K /
3088K / 3387K / 3750K / 4200K /
4773K / 5526K / 6563K / 8077K /

10500K / 15000K

ATW / MANUAL / SPECIFIC COLOR / PUSH

ATW

MANUAL

SPECIFIC
COLOR

DAY & NIGHT DAY & NIGHT

DAY THRESHOLD

DELAY TIME

NIGHT THRESHOLD

AUTO / BW / COLOR

AUTO

0 ~ 255

0 SEC ~ 10 SEC

0 ~ 255

20

21

9. OSD MANUAL

- IMAGE Menu

IMAGE Y GAMMA

ZONE SELECT

OFF / H FLIP / V FLIP / HV FLIP

C GAMMA

MASK ON / OFF

COLOR

TRANSPARANT

POSITION
CONTROL

ZONE 0 ~ ZONE 14

ON / OFF

WHITE / BLACK / RED / GREEN / BLUE

YELLOW / CYAN / MAGENTA

0 / 0.5 / 0.75 / 1

0 ~ 1080V SIZE

0 ~ 1920H SIZE

0 ~ 1080V POSITION

0 ~ 1920H POSITION

ON / OFFMOSAIC

GAMMA

SHARPNESS

CONTRAST

SATURATION

DNR

PRIVACY

MIRROR

0 ~31

0 ~ 31

0 ~ 31

OFF / LOW / MIDDLE / HIGH

PRESET 0 ~ PRESET 3

PRESET 0 ~ PRESET 3

22

9. OSD MANUAL

- SYSTEM Menu

SYSTEM FIRMWARE VER

COMMUNICATION CAMERA ID

BAUD RATE

NO. 0 ~ NO.255

2.4K / 4.8K / 9.6K

19.2K / 38.4K /57.6K

COMM APPLY

FOCUS MODE

AUDIO MODE

ON / OFF

ENABLE / DISABLE

FACTORY RESET

23

9. OSD MANUAL

• Main Menu

- VIDEO : Select SDI out format and TV out format.

- LENS : Select the IRIS type and adjust the IRIS control value.

- EXPOSURE : Adjust exposure control.

- WHITE BALANCE : Adjust white balance control.

- DAY / NIGHT : Day & Night control.

- IMAGE : Apply image processing effects.

- SYSTEM : System information & setting.

- EXIT : Close OSD Menu.

MAIN MENU

＋ VIDEO
＋ LENS
＋ EXPOSURE
＋ WHITE BALANCE
＋ DAY / NIGHT
＋ IMAGE
＋ SYSTEM

＊ EXIT

24

9. OSD MANUAL

• Video

- SDI RESOLUTION

Use the LEFT/RIGHT button to select the SDI
output video resolution - 720p, 1080i, 1080p

* Note : When the OSD menu is not displayed on video,
720p resolution can be selected by pressing the UP
button in 5 seconds. Similarly, 1080p resolution can be
selected by pressisng the DOWN button in 5 seconds.

- SDI FRAME RATE

Use the LEFT/RIGHT button to select the SDI output video frame rate

SDI resolution Available frame rate

1080p 30Hz, 25Hz

1080i 60Hz, 50Hz

720p 30Hz, 25Hz, 60Hz, 50Hz

- CVBS FORMAT

Use the LEFT/RIGHT button to select the TV out video format - NTSC, PAL

* Note : When the OSD menu is not displayed on video, NTSC video format can be selected by pressing
the LEFT button. Similarly, PAL video format can be selected by pressing the RIGHT button.

- VIDEO APPLY

Apply all video setting changed at once. Use the SET button to apply.

- ESC

Back to the prevois menu page.

• LENS

- LENS TYPE

Use the LEFT/RIGHT button to select the lens
type for iris control.

- DC IRIS(VIDEO IRIS), MANUAL IRIS.

- IRIS VOLUME

Use the LEFT/RIGHT button to adjust the iris
volume level.
Iris volume control does not apply when the
LENS TYPE is set to MANUAL IRIS.

VIDEO OUT

＊ SDI RESOLUTION
＊ SDI FRAME RATE
＊ CVBS FORMAT

＋ VIDEO APPLY

＊ ESC
＊ EXIT

1080p

30HZ

NTSC

LENS

＊ LENS TYPE
＊ IRIS VOLUME

＊ ESC
＊ EXIT

DC IRIS

25

25

9. OSD MANUAL

• EXPOSURE

- SHUTTER

Use the SET button to go to the SHUTTER sub menu.

- FLICKERLESS

Use the LEFT/RIGHT button to select the flickerless control
setting - OFF, 60Hz, 50Hz.

- BRIGHTNESS

Use the LEFT/RIGHT button to adjust the brightness reference level.

- AGC

Use the LEFT/RIGHT button to adjust the AGC max value

- BLC

Use the LEFT/RIGHT button to select ON/OFF the Back-Light
Compensation control.

- WDR

Use the LEFT/RIGHT button to select ON/OFF the Wide Dynamic
Range effect control.

EXPOSURE

＋ SHUTTER
＊ FLICKERLESS
＊ BRIGHRNESS
＊ AGC
＊ BLC
＊ WDR

＊ ESC
＊ EXIT

OFF

30

140
OFF
OFF

26

9. OSD MANUAL

• SHUTTER (Sub Menu)

- SHUTTER MODE

Use the LEFT/RIGHT button to select shutter & gain control mode

- NORMAL AE, AE HOLD, MANUAL.

- AE PRIORITY

This menu can be accessed when the SHUTTER MODE is set to NORMAL AE.
Use the LEFT/RIGHT button to select the AE control priority setting.

- NORMAL, GAIN, SHUTTER.

- USER MODE

This menu can be accessed when the SHUTTER MODE is set to MANUAL.
Use the LEFT/RIGHT button to select the user mode(1~4) to save setting.

- GAIN LEVEL

In GAIN priority mode at NORMAL AE mode.
This menu can be accessed when the SHUTTER MODE is set to
NORMAL AE and AE PRIORITY is set to GAIN.
Use the LEFT/RIGHT button to select the Gain value setting.

- GAIN LEVEL

In MANUAL mode.
This menu can be accessed when the SHUTTER MODE is set to MANUAL.
Use the LEFT/RIGHT button to select the Gain level setting.

- SHUTTER LEVEL

This menu can be accessed when the SHUTTER MODE is set to MANUAL.
Use the LEFT/RIGHT button to select the Shutter level setting.

SHUTTER

＊ SHUTTER MODE
＊ AE PRIORITY

＊ ESC
＊ EXIT

NORMAL AE

NORMAL

SHUTTER

＊ SHUTTER MODE

＊ ESC
＊ EXIT

AE HOLD

SHUTTER

＊ SHUTTER MODE
＊ AE PRIORITY
＊ GAIN LEVEL

＊ ESC
＊ EXIT

NORMAL AE

GAIN

0 DB

SHUTTER

＊ SHUTTER MODE
＊ USER MODE
＊ GAIN LEVEL

＊ SHUTTER LEVEL

＊ ESC
＊ EXIT

MANUAL

1

20
50

SHUTTER

＊ SHUTTER MODE
＊ AE PRIORITY
＊ SHUTTER LEVEL

＊ ESC
＊ EXIT

NORMAL AE

SHUTTER

25

27

9. OSD MANUAL

• WHITE BALANCE

- MODE

Use the LEFT/RIGHT button to select White balance modes

- ATW, MANUAL, SPECIFIC COLOR, PUSH

ATW Auto trace white balance mode
MANUAL Manual white balance mode
SPECIFIC COLOR Manual setting with target color temperature
PUSH White Balance Push mode to Auto AWB

- ATW MODE

This menu can be accessed when the WB MODE is set to ATW.
Use the LEFT/RIGHT button to select environment setting. - INDOOR, OUTDOOR

- TARGET TEMP

This menu can be accessed when the WB MODE is set to SPECIFIC COLOR.
Use the LEFT/RIGHT button to select target color temperature.

- R GAIN

This menu can be accessed when the WB MODE is set to MANUAL.
Use the LEFT/RIGHT button to adjust the Red Gain.

- B GAIN

This menu can be accessed when the WB MODE is set to MANUAL.
Use the LEFT/RIGHT button to adjust the Blue Gain.

WHITE BALANCE

＊ WB MODE
＊ ATW MODE

＊ ESC
＊ EXIT

ATW

INDOOR

WHITE BALANCE

＊ WB MODE
＊ R GAIN

＊ B GAIN

＊ ESC
＊ EXIT

MANUAL

48
64

WHITE BALANCE

＊ WB MODE
＊ TARGET TEMP

＊ ESC
＊ EXIT

SPECIFIC COLOR

3387K

WHITE BALANCE

＊ WB MODE

＊ ESC
＊ EXIT

PUSH

28

9. OSD MANUAL

• Day / Night

- DAY & NIGHT:

Use the LEFT/RIGHT button to select Day & Night modes

- AUTO, EXT, COLOR, BW

AUTO Auto controlled by AGC level in the processor. (AGC Type)
EXT Auto controlled by EXT signal.
COLOR Fixed Day State. Color Image.
BW Fixed Night State. BW Image.

- DELAY TIME:

This menu can be accessed when the DAY & NIGHT is set to AUTO.
Use the LEFT/RIGHT button to select state change delay time.

- DAY THRESHOLD:

This menu can be accessed when the DAY & NIGHT is set to AUTO.
Use the LEFT/RIGHT button to select threshold value of change from
night state to day state.

- NIGHT THRESHOLD:

This menu can be accessed when the DAY & NIGHT is set to AUTO.
Use the LEFT/RIGHT button to select threshold value of change from
day state to night state.

DAY & NIGHT

＊ DAY & NIGHT
＊ DELAY TIME
＊ DAY THRESHOLD

＊ NIGHT THRESHOLD

＊ ESC
＊ EXIT

AUTO

3 SEC

101
188

DAY & NIGHT

＊ DAY & NIGHT

＊ ESC
＊ EXIT

EXT

DAY & NIGHT

＊ DAY & NIGHT

＊ ESC
＊ EXIT

COLOR

DAY & NIGHT

＊ DAY & NIGHT

＊ ESC
＊ EXIT

BW

9. OSD MANUAL

• IMAGE

- GAMMA: Use the SET button to go to the GAMMA sub menu.

- SHARPNESS: Use the LEFT/RIGHT button to adjust the sharpness value.

- CONTRAST: Use the LEFT/RIGHT button to adjust the contrast value.

- SATURATION: Use the LEFT/RIGHT button to adjust the saturation level.

- DNR: Use the LEFT/RIGHT button to select the digital noise reduction

level. - OFF, LOW, MIDDLE, HIGH

- PRIVACY: Use the SET button to go to the PRIVACY MASK sub menu.

- MIRROR: Use the SET button to select image flip modes.

- OFF, H FLIP, V FLIP and H/V FLIP.

• GAMMA (Sub Menu)

- Y GAMMA:

Use the LEFT/RIGHT button to select preset gamma setting for luma.

- C GAMMA:

Use the LEFT/RIGHT button to select preset gamma setting for chroma.

29

IMAGE

＋

GAMMA

＊ SHARPNESS
＊ CONTRAST
＊ SATURATION
＊ DNR
＋ PRIVACY
＊ MIRROR

＊ ESC
＊ EXIT

7
17
18

OFF
OFF

GAMMA

＊ Y GAMMA
＊ C GAMMA

＊ ESC
＊ EXIT

RPESET 2
RPESET 3

9. OSD MANUAL

• PRIVACY MASK (Sub Menu)

- ZONE SELECT: Use the LEFT/RIGHT button to select the mask

zone number to setting.

- MASK ON/OFF: Use the LEFT/RIGHT button to select ON/OFF
the mask that is zone selected.

- TRANSPARENT: Use the LEFT/RIGHT button to adjust the mask transparent
level.

- COLOR: Use the LEFT/RIGHT button to select the mask color.

- POSITION CONTROL: Use the SET button to go to the mask position setting sub

menu

• PRIVACY MASK (Sub Menu)

- V SIZE: Use the LEFT/RIGHT button to adjust the mask vertical size.

- H SIZE: Use the LEFT/RIGHT button to adjust the mask horizontal size.

- V POSITION: Use the LEFT/RIGHT button to adjust the mask vertical position.

- H POSITION: Use the LEFT/RIGHT button to adjust the mask horizontal position.

- MOSAIC: Use the LEFT/RIGHT button to select ON/OFF the mask mosaic

setting.

PRIVACY MASK

＊ ZONE SELECT
＊ MASK ON / OFF
＊ TRANSPARANT
＊ COLOR

＋ POSITION CONTROL

＊ ESC
＊ EXIT

ZONE 0

OFF

0.5

WHITE

PRIVACY MASK

＊ V SIZE
＊ H SIZE
＊ V POSITION
＊ H POSITION
＊ MOSAIC

＊ ESC
＊ EXIT

0
0
0
0

OFF

30

31

9. OSD MANUAL

• SYSTEM

- FIRMWARE VER : Information of camera’s

firmware version.

- COMMUNICATION: Use the SET
button to go to the
COMMUNICATION sub
menu.

- AUDIO OUTPUT: Use the LEFT/RIGHT
button to select the
audio output ENABLE/
DISABLE.

- FOCUS MODE: Use the LEFT/RIGHT button to select ON/OFF the Focus
mode. In Focus mode, the iris becomes fully open, electronic
shutter controls the light level, and the TV out screen zooms
into the center in order to make focusing easier. When in
Focus Mode, the OSD menu is not displayed.

- FACTORY RESET: Use the SET button to action start of reset. Clear all setting
and initialize to factory setting.

• COMMUNICATION (Sub Manu)

- CAMERA ID : Use the LEFT/RIGHT button

to select the RS485 ID
Address.

- BAUD RATE : Use the LEFT/RIGHT button
to select the baudrate setting
for RS485 communication.

- COMM APPLY : Apply all communication
setting changed at once.
Use the SET button to apply.

• EXIT

This menu can be accessed when use the EXIT action in all menu pages.

- SAVE & EXIT SETUP:

Save all current setting and Close OSD
menu. These setting are loaded and applied
automatically when the Camera is power on.

- EXIT WITHOUT SAVING:

Close OSD menu. Camera’s current setting is
not saved. Use the SET button to action.

SYSTEM

＊ FIRMWARE
＊ COMMUNICATION
＊ AUDIO OUTPUT
＊ FOCUS MODE
＊ FACTORY RESET

＊ ESC
＊ EXIT

0.2B.25

DISABLE

OFF

COMMUNICATION

＊ CAMERA ID
＊ BAUD RATE

＊ COMM APPLY

＊ ESC
＊ EXIT

NO. 1

2.4K

SAVE & EXIT SETUP

EXIT WITHOUT SAVING

Quick Setup Guide

(HD CCTV CAMERA)

■

OSD Menu Button.

- Video out Format Change (NTSC/PAL Selection)

Default(Factory default setting) video out format is NTSC.
Camera power on & Until push the SET button(While OSD menu is not displayed on
video), Can select NTSC/PAL video format output on VIDEO port - Push the LEFT
button to select NTSC format video out mode or Push the RIGHT button to select
PAL format video out mode.

*Warning : When HD-SDI out format is setted 1080P, NTSC/PAL video out
is not supported. While OSD menu is not displayed on video, Can select
1080P/720P format output on HD-SDI port - Push the UP button in 3 seconds
to select 720P format video out or Push the DOWN button in 3 seconds to
select 1080p format video out.

- OSD menu Display on Video

Push the SET button.

- Use the Focus mode

Can be found in SYSTEM menu section in OSD menu.
Use the LEFT/RIGHT button to select ON/OFF the Focus mode.

·Video output port

- HDcctv 1.0 OUTPUT (BNC) :

HD-SDI video out to HDcctv DVR or Other HDcctv Signal Equipment.

- VIDEO (BNC) :

NTSC or PAL video out to Hand-Held Test Equipment(TV Monitor).

·Focus Mode

In the Focus mode, the Iris becomes fully open and the TV out screen zooms into
the center in order to make focusing easier.
When turn on the Focus mode, the OSD menu display in turned off automatically
and when turn off the focus mode, the OSD menu display is back.

UP / 720p

DOWN / 1080p

LEFT / NTSC RIGHT / PAL