KT&C KPC-HDN722M User Manual

HD CCTV
Digital Video Camera

OPERATION MANUAL

M161-HDN722-001

Thank you for choosing our high quality camera.
Before attempting to connect operate this unit, please read and follow these instructions.

CAUTION

These servicing instructions are for use by qualied service personnel only.

To reduce the risk of electric shock do not perform any servicing other than that

contained in the operating instructions unless you are qualied to do so.

Use Class 2 Power Supply Only

2

CONTENTS

1. CAUTIONS

2. IMPORTANT SAFETY INSTRUCTION

3. FEATURES

4. EQUIPMENT AND ACCESSORIES

5. INSTALLATION

6. DIMENSIONS

7. SPECIFICATION

8. OSD MANUAL

3

1. CAUTIONS

This device complies with Part 15 of the FCC Rules.
Operation is subject to the following two conditions;

1. This device may not cause harmful interference.

2. This device must accept any interference received, including interference
that may cause undesired operation.

Note

This equipment has been tested and found to comply with the limits for a Class A digital
device, pursuant to part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference when the equipment is operated
in a commercial environment. This equipment generates, uses, and can radiate radio
frequency energy and, if not installed and used in accordance with the instruction
manual, may cause harmful interference to radio communications. Operation of this
equipment in a residential area is likely to cause harmful interference in which case the
user will be required to correct the interference at his own expense.”

WARNING

This is a class A product. In a domestic environment this product may cause radio
interference in which case the user may be required to take adequate measures.

Caution

Any changes or modications in construction of this devices which are not expressly

approved by the party responsible for compliance could void the user’s authority to
operate the equipment.

1. A regulated DC12V 1A power supply is recommended for use with this camera
for the best picture and the most stable operation.
An unregulated power supply can cause damage to the camera.

When unregulated power supply is applied, product warranty will be out of subject.

2. It is recommended that the camera is used with a monitor that has a CCTV

quality 75Ω video impedance level.

If yur monitor is switched to high impedance then please adjust accordingly.

3. Do not attempt to disassemble the camera to gain access to the internal components.

Refer servicing to your dealer.

4. Never face the camera towards the sun or any bright or reective light,

which may cause smear on the picture and possible damage to the Image Sensor.

5. Do not remove the serial sticker for the warranty service.

6. Do not expose the camera to rain or other types of liquid.

7. The apparatus must be connected to a mains socket-outlet with a protective earthing

connection.

4

1. CAUTIONS

Correct Disposal of This Product

(Waste Electrical & Electronic Equipment)

(Applicable in the European Union and other European countries with
separate collection systems)

This marking shown on the product or its literature, indicate that it should not
be disposed with other household wastes at the end of its working life. To
prevent possible harm to the environment or human health from uncontrolled
waste disposal, please separate this from other types of wastes and recycle it
responsibly to promote the sustainable reuse of material resources.

This product should not be mixed with other commercial wastes purchased this

product, or their local government ofce, for details of where and how they can

take item for environmentally safe recycling.
Business users should contact their supplier and check the terms and

conditions of the purchase contract.
Household users should contact either the retailer where they for disposal.

5

2. IMPORTANT SAFETY INSTRUCTION

1) Read these instructions.

2) Keep these instructions.

3) Heed all warnings.

4) Follow all instructions.

5) Do not use this apparatus near water.

6) Clean only with dry cloth.

7) Do not block any ventilation openings. Install in accordance
with the manufacturer’s instructions.

8) Do not install near any heat sources such as radiators, heat registers,

stoves, or other apparatus (including ampliers) that produce heat.

9) Do not defeat the safety purpose of the polarized or grounding-type plug. A
polarized plug has two blades with one wider than the other. A grounding type
plug has two blades and a third grounding prong. The wide blade or the third

prong are provided for your safety. If the provided plug does not t into your

outlet, consult an electrician for replacement of the obsolete outlet.

10) Protect the power cord from being walked on or pinched particularly at plugs,
convenience receptacles, and the point where they exit from the apparatus.

11) Only use attachments/accessories specied by the manufacturer.

12) Use only with the cart, stand, tripod, bracket, or table specied by

the manufacturer, or sold with the apparatus. When a cart is used,
use caution when moving the cart/apparatus combination to
avoid injury from tip-over.

13) Unplug this apparatus during lightning storms or when unused for long

periods of time.

14) Refer all servicing to qualied service personnel. Servicing is required when

the apparatus has been damaged in any way, such as power-supply cord
or plug is damaged, liquid has been spilled or objects have fallen into the
apparatus, the apparatus has been exposed to rain or moisture, does not
operate normally, or has been dropped.

6

3. FEATURES

• High Resolution

SONY 1 / 3” 2.1M Progressive Color CMOS Image Sensor,
1080p(1920x1080)@30fps (Standard)

• Support various digital video output

1080p@30fps, 1080p@25fps, 720p@60fps, 720p@50fps

• Video Outputs

Primary HD-SDI (BNC)
Test/Setup TV Out (Test Point-adapter to BNC included) NTSC/PAL selectable

• OSD menu for setup and configuration

• Support RS485 Communucation Protocol for

Camera Configuration Remote Control

• Lens Control

DC Iris

• 8 Hyper LED and range to 40m ( 131 Feet )

• Provides True Day/Night Capability with Motorized IR Cut Filter

• Power Source

DC12V, DUAL(DC 12V / AC 24V)

• IP67 Weather Resistant

7

4. EQUIPMENT AND ACCESSORIES

HD CCTV
Digital Video Camera

SERVICE VIDEO OUTPUT
TEST CABLE

L WRENCH

OPERATION MANUAL

SCREW - 4ea

8

5. INSTALLATION

• CAMERA MOUNTING POSITION

90˚ TLIT

90˚ TLIT

<Cable Concealed Thru Bracket>

360˚ PAN

9

360˚ PAN

5. INSTALLATION

• External Zoom & Focus Adjustable

The workmanship to adjust zoom and focus,
opening the window cap might cause the
humidity problems to the camera. The External
Zoom and Focus system with out state-of-the­art technology provides easy camera installation
without opening the window cap to adjust zoom
and focus the lens.

• Service Video Out & OSD Control

• OSD Control Joystick

Up

Left

Down

• Service video connector • Power LED

Right

10

5. INSTALLATION

• MONITOR CONNECTION

DC12V / AC24V

RS485(+)
RS485(-)

VIDEO IN

SDI
RECEIVER
DISPLAY

HD SDI IN

DEVICE

DC12V / AC24V REGULATED
POWER SUPPLY

TEST CABLE

DC12V

TEST CABLE

When you install the camera, please seal the ends of cables to protect
the camera connections from humidity problems.

11

RS485(+)
RS485(-)

VIDEO IN

HANDHELD

MONITOR

SDI
RECEIVER
DISPLAY

HD SDI IN

DEVICE

DC12V REGULATED
POWER SUPPLY

HANDHELD

MONITOR

6. DIMENSIONS

DC12V / AC24V

98.6
196

83

High power LED

Photo cell

DC12V

83

High power LED

Photo cell

Unit(mm)

98.6

Lens

Lens

88.3

88.3

140

110.5

168.6

250

329

160

M15xP1.25

10

150

10

2ea

Ø110

M15xP1.25

2ea

125

12

Ø95

7. SPECIFICATION

Image Device 2.1 Mega Pixel, 1/3” Exmor CMOS
Effective Pixels 1984 (H) x 1105 (V)
Unit cell size 2.8um (H) x 2.8um (V)

Video output mode
Minimum illumination 0 Lux ( IR LED ON )

Video output HD-SDI / 1.0 Vp-p Composite (75Ω)
IR LED 850 nm, Hyper LED (8 ea)
IR Beam Range Up to 40 m (131 feet)
S/N Ratio More than 50dB
Shutter speed Auto / Manual selectable
Manual Shutter

speed
WDR / BLC OFF / WDR / BLC / D-WDR
AGC Max. 29 dB
3DNR OFF / LOW / MIDDLE / HIGH
Day & Night True Day & Night with ICR Mechanism
White Balance AUTO / AUTOext / PUSH / MANUAL
Digital Zoom Ratio 1x ~ 20x
Digital Slow Shutter Off, x2 ~ x8
Privacy Masking Zone 24 ea, On / Off
Lens Control DC Iris Varifocal Lens ( ICR )
Angle View Wide: 92.9°(H) x 67.9°(V) / Tele: 31.7°(H) x 23.7°(V)
OSD Built-in

Power
Consumption

Dimension
(mm)

IP Rating IP67 (Water Proof)
Weight Approx. 1.37 kg (DC12V) / Approx. 1.9 kg (Dual)
Conformity CE, FCC, KC
Operating Temperature 14°F~112°F (-10°C ~ 50°C)
Storage Temperature -4˚F~140˚F (-20˚C ~ 60°C)
Humidity Operating: Less than 80% / Storage: Less than 95%

HD-SDI: 1080p@30fps, 1080p@25fps, 720p@60fps, 720p@50fps

DC12V DC12V (±10%), Max. 700 mA
Dual
DC12V 99(W) x 83(H) x 111(D)

Dual 99(W) x 83(H) x 169(D)

Specications and designs are subject to change for improving

the functionality of this product without notice.

TV Out: NTSC / PAL selectable

1/30(25), 1/60(50), 1/120(100), 1/240, 1/500,

1/1K, 1/2K, 1/4K, 1/8K, 1/16K, 1/30K, 1/60K

DC12V (±10%), Max. 700 mA /

AC24V (±10%), Max. 8.5 W

13

8. OSD MANUAL

• Menu structure

SETUP
EXPOSURE

WHITE BALANCE
WDR / BLC
DNR
IMAGE
SPECIAL
SYSTEN
RESET DATA ALL
EXIT

Main Sub Menu Sub Menu

EXPOSURE

WHITE
BALANCE

WDR / BLC

DNR OFF, LOW, MIDDLE, HIGH

BRIGHTNESS 0 ~ 20
AE MODE NORMAL AE / INDOOR
LENS(IRIS) MANUAL / AUTO

SHUTTER

DSS Off / X2 / X3 / X4 / X5 / X6 / X7 / X8
AGC 0 ~ 10
NIGHT

ANTI-SAT
BASE FREQ 60Hz / 50Hz
RESET DATA BACK / DEF.
RETURN BACK / EXIT.

WB MODE

SATURATION 0 ~ 20
RESET DATA BACK / DEF.
RETURN BACK / EXIT.
MODE OFF / WDR / BLC / D-WDR
WDR WGT 0 ~ 4
BLC OSD OFF ~ ON
BLC POS-X 0 ~ 20
BLC POS-Y 0 ~ 20
BLC SIZE-X 0 ~ 20
BLC SIZE-Y 0 ~ 20
RESET DATA BACK / DEF.
RETURN BACK / EXIT.

LEVEL

MANUAL /
AUTO

RETURN BACK / EXIT

0 ~ 20

COLORTEMP. LOW / MIDDLE / HIGH

AUTO

R-GAIN 0 ~ 20

/AUTOext
/PUSH

B-GAIN 0 ~ 20

/MANUAL

RETURN BACK / EXIT

1/30(25), 1/60(50), 1/120(100), 1/240, 1/500,
1/1K, 1/2K, 1/4K, 1/8K, 1/16K, 1/30K, 1/60K.

14

8. OSD MANUAL

Main Sub Menu Sub Menu

IMAGE

SPECIAL

SYSTEM

SHARPNESS 0 ~ 20
GAMMA 0 ~ 4
FLIP OFF, H FLIP, V FLIP, HV FLIP
LENS SHADING OFF, ON
DZOOM 1x, 2x, 4x, 6x, 8x, 10x, 12x, 14x, 16x, 18x, 20x
RESET DATA BACK / DEF.
RETURN BACK / EXIT.

PRIVACY OFF/ ON

HLMASK OFF/ ON

PATTERN OFF / 0 / 1
DISPLAY INFO.
RESET DATA BACK / DEF.

RETURN BACK / EXIT.

COMM. ADJUST

SDI FORMAT 1080P / 720P
SDI FPS 30(60) / 25(50)

CVBS FORMAT

APPLY OK / ON

SYSTEM INFO.

REBOOT
RETURN BACK / EXIT.

NTSC /
PAL

ZONE NO. 0 ~ 23
ZONE OP. OFF/ ON
X-POS 0 ~ 60
Y-POS 0 ~ 40
X-SIZ 0 ~ 40
Y-SIZ 0 ~ 40

COLOR
TRANS. 0 ~ 4

RESET DATA BACK / DEF.
RETURN BACK / EXIT.
LEVEL 0 ~ 20

COLOR
RESET DATA BACK / DEF.

RETURN BACK / EXIT.

CAMERA ID. OFF/ ON
RETURN BACK / EXIT.

CAMERA ID. 1 ~ 254
BAUDRATE
APPLY & EXIT OK / ON

RETURN BACK / EXIT.

CVBS OUT AUTO / OFF / ON(WDR OFF)
CVBS VIEW CROP / FULL
RETURN BACK / EXIT.

S/W VERSION
SET VERSION
RETURN BACK / EXIT.

BLK, WHI, YEL, CYN, GRN,
MAG, RED, BLU

BLK, WHI, YEL, CYN, GRN,
MAG, RED, BLU

2400, 4800, 9600, 19200,
38400, 57600, 115200

15

8. OSD MANUAL

• Function Description

0. SETUP

- EXPOSURE : Go sub menu for camera exposure control.

- WHITE ALANCE : Go sub menu for camera white balance control.

- WDR / BLC : Go sub menu for camera WDR or BLC action.

- DNR : Control noise reduction setting.

- IMAGE : Go sub menu for adjust image functions.

- SPECIAL : Go sub menu for special feature control.

- SYSTEM : Go sub menu for system control & information.

- Reset Data All : Reset camera’s all feature data to default value.

1. EXPOSURE

- BRIGHTNESS : Adjust image brightness value.

- AE MODE : Adjust AE control mode.

- LENS(IRIS) : Select lens iris control type.

- SHUTTER : Select shutter speed control type.

• LEVEL : Adjust shutter speed at manual shutter mode.

- DSS : Adjust digital slow shutter control level.

- AGC : Adjust max gain level for brightness control.

- NIGHT ANTI-SAT : Adjust Night Anti-Sat level for Saturation Level.

- BASE FREQ : Select basic control frequency for control camera feature.

2. WHITE BALANCE

- WB MODE : Select white balance control mode.

• AUTO : Full auto control mode in color temperature rage 2300K~10000K.

• AUTOext : Extended auto mode for special illumination.

• PUSH : Enable fix the control setting for specific environment.

• MANUAL : Enable WB control setting by user’s intention.

COLOR TEMP. : Select color temperature range for WB control at manual mode.

◦

R-GAIN : Adjust red color gain for WB control at maual mode.

◦

B-GAIN : Adjust blue color gain for WB control at manual mode.

◦

- SATURATION : Adjust color saturation level.

3. WDR/BLC

- MODE : Select WDR for BLC mode.

• WDR : Act in wdie dynamic rage mode. Controled video frame rate in 1/2.

• BLC : Act in Backlight compensation mode.

• D-WDR : Digital wide dynamic range control.

Push & release, for fix WB control setting.

This mode can be accessed when CVBS out setting, is "set to OFF" or
"set to AUTO(When is not connected the video cable)"

16

8. OSD MANUAL

- WDR WGT : WDR weight control level settig at WDR mode.

- BLC OSD : Display BLC control zone in screen.

- BLC POS-X : Select BLC control zone vertical position.

- BLC POS-Y : Select BLC control zone horizontal position.

- BLC SIZ-X : Select BLC control zone vertical size.

- BLC SIZ-Y : Select BLC control zone horizontal size.

4. DNR: Reduce image’s noise

5. IMAGE

- SHARPNESS : Adjust image sharpness level.

- GAMMA : Gamma Curve Select.

- FLIP : Vertical & Horizontal flip setting.

- LENS SHADING : Enable lens shading compensation.

- DZOOM : Select digital zoom magnification.

6. SPECIAL

- PRIVACY : Setting for protect private area in image using mask setting.

• ZONE NO. : Select private mask zone number.

• ZONE OP. : Select zone mask display on/off.

• X-POS : Select zone horizontal position.

• Y-POS : Select zone vertical position.

• X-SIZ : Select zone horizontal size.

• Y-SIZ : Select zone vertical size.

• COLOR : Select mask color

• TRANS. : Select mask transparency level.

- HLMASK : Mask image high light area.

• LEVEL : Select high light level.

• COLOR : Select mask color.

- PATTERN : Color bar display Select.

- DISPLAY INFO. : Camera information OSD on/off.

• CAMERA ID. NUM.

17

8. OSD MANUAL

7. SYSTEM

- COMM. ADJUST : RS-485 Communication Setting mode.

• CAMERA ID. : RS-485 CAM ID Select.

• BAUDRATE : RS-485 Communication Speed Select.

• Apply & Exit : Apply all RS-485 Setting changed at once.

- SDI FORMAT : 1080P / 720P

- SDI FPS : 30 or 25 fps in 1080p mode.

- CVBS FORMAT : NTSC / PAL

• CVBS OUT : Select mode for CVBS out action.
ON, OFF : Enable or Disable CVBS out data.

◦

AUTO : Check automatically CVBS video cable connection.

◦

• CVBS VIEW : CVBS out video angle setting.
CROP : Cut the scene outside area for keep image aspect ratio.

◦

FULL : Fill the full angle scene into image with H-V size & ratio

◦

- APPLY : Apply all video setting changed at once.

- SYSTEM INFO.

• S/W VERSION : Camera’s basic software version.

• SET VERSION : Camera’s feature control setting version.

Use the Set button to apply.

60 or 50 fps in 720p mode.

If connected, CVBS out data is enable and WDR mode is
setted off automatically.

change.
Use the Set button to apply.

18