KT&C KPC-HDN300M User Manual

HD CCTV Digital Video Camera
OPERATION MANUAL
M162-HDN300-001
Thank you for choosing our high quality camera. Before attempting to connect operate this unit, please read and follow these instructions.
CONTENTS
1. CAUTIONS
2. IMPORTANT SAFETY INSTRUCTION
3. EQUIPMENT AND ACCESSORIES
4. INSTALLATION
5. DIMENSIONS
6. SPECIFICATION
7. OSD MANUAL
CAUTION
These servicing instructions are for use by qualied service personnel only.
contained in the operating instructions unless you are qualied to do so.
Use Class 2 Power Supply Only
2
1. CAUTIONS
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions;
1. This device may not cause harmful interference.
2. This device must accept any interference received, including interference that may cause undesired operation.
Note
This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense.”
WARNING
This is a class A product. In a domestic environment this product may cause radio interference in which case the user may be required to take adequate measures.
Caution
Any changes or modications in construction of this devices which are not expressly
approved by the party responsible for compliance could void the user’s authority to operate the equipment.
1. A regulated DC12V 1A power supply is recommended for use with this camera for the best picture and the most stable operation. An unregulated power supply can cause damage to the camera.
When unregulated power supply is applied, product warranty will be out of subject.
2. It is recommended that the camera is used with a monitor that has a CCTV
quality 75Ω video impedance level.
If yur monitor is switched to high impedance then please adjust accordingly.
3. Do not attempt to disassemble the camera to gain access to the internal components.
Refer servicing to your dealer.
4. Never face the camera towards the sun or any bright or reective light,
which may cause smear on the picture and possible damage to the Image Sensor.
5. Do not remove the serial sticker for the warranty service.
6. Do not expose the camera to rain or other types of liquid.
7. The apparatus must be connected to a mains socket-outlet with a protective earthing
connection.
3
1. CAUTIONS
Correct Disposal of This Product
(Waste Electrical & Electronic Equipment)
(Applicable in the European Union and other European countries with separate collection systems)
This marking shown on the product or its literature, indicate that it should not
be disposed with other household wastes at the end of its working life. To
prevent possible harm to the environment or human health from uncontrolled waste disposal, please separate this from other types of wastes and recycle it
responsibly to promote the sustainable reuse of material resources.
This product should not be mixed with other commercial wastes purchased this
product, or their local government ofce, for details of where and how they can take item for environmentally safe recycling.
Business users should contact their supplier and check the terms and conditions of the purchase contract. Household users should contact either the retailer where they for disposal.
RISK OF ELECTRIC SHOCK DO NOT OPEN
CAUTION TO REDUCE THE RISK OF ELECTRIC
This symbol is intended to alert the user to the presence of uninsulated
"dangerous voltage" within the product's enclosure that may be of sufcient
mangnitude to constitute a risk of electric shock to persons.
This symbol is intended to alert the user to the presence of important operating
and maintenance(servicing) instruction in the literature accompanying the
appliance.
SHOCK, DO NOT REMOVE COVER(OR BACK).
NO USER. SERVICING TO QUALIFED SERVICE PERSONNEL.
CAUTION
4
2. IMPORTANT SAFETY INSTRUCTION
1) Read these instructions.
2) Keep these instructions.
3) Heed all warnings.
4) Follow all instructions.
5) Do not use this apparatus near water.
6) Clean only with dry cloth.
7) Do not block any ventilation openings. Install in accordance with the manufacturer’s instructions.
8) Do not install near any heat sources such as radiators, heat registers,
stoves, or other apparatus (including ampliers) that produce heat.
9) Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized plug has two blades with one wider than the other. A grounding type plug has two blades and a third grounding prong. The wide blade or the third
prong are provided for your safety. If the provided plug does not t into your
outlet, consult an electrician for replacement of the obsolete outlet.
10) Protect the power cord from being walked on or pinched particularly at plugs, convenience receptacles, and the point where they exit from the apparatus.
11) Only use attachments/accessories specied by the manufacturer.
12) Use only with the cart, stand, tripod, bracket, or table specied by
the manufacturer, or sold with the apparatus. When a cart is used, use caution when moving the cart/apparatus combination to avoid injury from tip-over.
13) Unplug this apparatus during lightning storms or when unused for long
periods of time.
14) Refer all servicing to qualied service personnel. Servicing is required when
the apparatus has been damaged in any way, such as power-supply cord or plug is damaged, liquid has been spilled or objects have fallen into the apparatus, the apparatus has been exposed to rain or moisture, does not operate normally, or has been dropped.
5
3. EQUIPMENT AND ACCESSORIES
Standard Type Cable Concealed Type
Camera
Sun shield
Tapping Screw
Ø4x20 (3ea)
Coin Hole Bolt
L-Wrench
Washer
Screw /
L-Wrench /
Washer /
Coin Hole
Bolt
Tapping Screw
Ø4x16 (3ea)
Coin Hole Bolt
Washer
Manual
CAUTION
• Service Video Output looks the angle of view narrower than HD-SDI Output.
6
4. INSTALLATION
• CAMERA MOUNTING POSITION
Cable Concealed
Thru Bracket(Option)
When using the cable concealed bracket, it is not
able to install on the ceiling.
Please assemble a coin
hole bolt as shown above.
7
4. INSTALLATION
• MONITOR CONNECTION
RCA Jack
(OSD Key Jack / White)
BNC Female (2'nd Video / Yellow)
DC12V IN (Black)
BNC Female
(HD-SDI Jack)
When you install the camera, please glue up the end of cable to keep it stable in order to protect the camera from the humidity problems.
* Option: Remote Control (OSD Key)
HD-SDI IN
* Remote Control - Circuit Diagram (Option)
Function
SW1: Menu OSD Menu on / off, Selection. SW2: Up OSD Menu up. SW3: Down OSD Menu Down. SW4: Left OSD Menu Left. SW5: Right OSD Menu Right.
Max. 35M
8
DC12V
Adapter
Monitor
SW5SW4SW3SW2SW1
RightLeftDownUpMenu
5. DIMENSIONS
Unit(mm)
20LED
Photocell
Option
Concealed Bracket
9
6. SPECIFICATION
Image Device 1/3” 2.1 Mega Pixel SONY CMOS
Effective Pixels 1984(H) x 1105(V)
Unit cell size 2.8um (H) x 2.8um (V)
Video output mode
Minimum Illumination
Shutter speed
Day/Night
White Balance AUTO / PUSH LOCK / Manual / AUTO EXT
AGC 0 ~ 23dB
Lens Board Lens
OSD Built-in (AD-Key Remote Controller)
IR-LED 850nm, 20ea, 10m
IP Rating IP 67 (Water Proof)
Power Consumption
ETC
Dimension 112mm(Ø) x 67mm (with sunshield)
Weight Approx. 360g
Temperature/ Humidity
Option
* Specifications and designs are subject to change for
SDI: 1080P 30fps(25fps) / 720P 60fps(50fps)
TV Out: CVBS NTSC/PAL
0 Lux (IR-LED ON)
Auto / Manual selectable
1/30(25),1/60(50),1/120(100),1/250,1/ 700,
1/1K,1/1.6K,1/2.5K,1/5K,1/7K,1/10K,1/30K
True Day&Night with ICR Mechanism
(AUTO/Color/BW)
DC 12V(±10%), Less than 380mA (IR-LED on)
Motion Detection, 3DNR, Mirror(H/V/HV)
DSS, BLC, Digital Zoom
Operation : -10~50 / 20~80%
Storage : -20~60 / 20~95%
Remote Controller (KA-05D)
Concealed Bracket
improving the functio
10
7. OSD MANUAL
1. EXPOSURE
- BRIGHTNESS: Enable user to control the image brightness (1~20steps).
- SHUTTER MODE: Enable user to set up the Shutter Mode. -> AUTO, MANUAL
- SHUTTER SPEED: Enable user to set up the Shutter Speed.
-> 1/30(25), 1/60(50), 1/120(100), 1/250, 1/700, 1/1K, 1/1.6K, 1/2.5K, 1/5K, 1/7K, 1/10K, 1/30K. *() is for power-frequency 50Hz.
- DSS(Digital Slow Shutter): Enable user to set up the DSS Level. -> OFF, X2, X3, X4.
- AGC MAX: Enable user to make imager bright to amplify the Gain (0~23dB).
- INITIAL: Enable user to initialize the Exposure menu set up.
EXPOSURE
> BRIGHRNESS SHUTTER MODE SHUTTER SPEED DSS AGC MAX INITIAL RETURN
||||||||||
|
AUTO – – – X2 18dB
|
10
2. WHITE BALANCE
Enable user to represent the accurate white color by controlling the R,G,B level.
- WB MODE
1. AUTO: Enable user to trace the White Balance automatically in the range of 2,300K~10,000K.
2. PUSH LOCK: Enable user to fix the White Balance according to the color temperature in the certain environment.
3. MANUAL: Enable user to sets the White Balance according to the circumstance.
4. AUTO EXT: Extended auto mode for special illumination.
WHITE BALANCE
> WB MODE CHROMA KELVIN RED GAIN BLUE GAIN PUSH AUTO INITIAL RETURN
AUTO
||||
– – – – – – – – – – – –
|||||||
|
7
- CHROMA: Enable user to set the Color Gain(0~20steps).
- KELVIN: In the MANUAL setting of WB MODE, enable user to set the color temperature range.
- RED GAIN: In the MANUAL setting of WB MODE, enable user to set the RED GAIN.
- BLUE GAIN: In the MANUAL setting of WB MODE, enable user to set the BLUE GAIN.
- PUSH AUTO: In the PUSH LOCK setting of WB MODE,
enable user to fix the White Balance in camera setting.
- INITIAL: Enable user to reset the WHITE BALANCE menu setting.
11
7. OSD MANUAL
3. BLC
- MODE: Enable user to set BLC mode.
-> OFF, BLC
- BLC(Backlight compensation mode): This function works for subjects in the kind of backlight conditions.
- BLC ZONE: Enable user to set up screen output of chosen BLC zone.
- BLC X-POSITION: Enable user to set up screen output of chosen BLC zone.
- BLC Y-POSITION: Enable user to set up Horizontal start position (0~20steps).
- BLC X-SIZE: Enable user to set up Vertical size (0~20steps).
- BLC Y-SIZE: Enable user to set up Horizontal size (0~20steps).
- INITIAL: Enable user to initialize the BLC setting.
BLC
> MODE BLC ZONE BLC X - POSITION BLC Y - POSITION BLC X - SIZE BLC Y - SIZE INITIAL RETURN
BLC OFF
|||| |||
||||||||||
|
||||||||||
|
||||||||
|||||||
|
6
|
4
|
7
|
10
4. DAY&NIGHT
Conversion of output image COLOR / BW depending on exterior environment.
- D&N MODE
1. COLOR: Enable user to fit the output image in color.
2. B/W: Enable user to fit the output image in B/W. 3 AUTO: Enable user to convert to COLOR/BW automatically by photocell
- DWELL TIME: In D&N MODE AUTO,
enable user to set to delay time for changing COLOR/BW(0~10sec).
DAY&NIGHT
> MODE DWELL TIME DAY -> NIGHT NIGHT -> DAY IR OPTIMIZER IR OPT. LEVEL INITIAL RETURN
- DAY->NIGHT: Threshold of switching from Day to Night.
- NIGHT->DAY: Threshold of switching from Night to Day.
- IR OPTIMIZER: By the IR LED light, the screen is saturated, and
automatically adjust the brightness, so you can see the screen.
- IR OPT. LEVEL: Enable user to set up IR OPTIMIZER level (0~15 level)
- INITIAL: Enable user to initialize the setting in DAY&NIGHT menu.
12
AUTO 3s
||||||||||
|
||||||||||
|
ON
||||||||||
|
|
1
|
2
|
7
7. OSD MANUAL
5. IMAGE
- SHARPNESS: Enable user to control the image sharpness(0~10steps).
- FLIP: Sets the Vertical flip for the display output.
IMAGE
> SHARPNESS
(OFF) (H-FLIP)
(V-FLIP) (HV-FLIP)
- DZOOM(Digital Zoom): Max. 20x Digital Zoom.
- HLMASK: This function that improves the visual recognition of license
plates and other such objects by suppressing or masking strong light sources.
1. HLMASK LEVEL: Enable user to set HLMASK Level(0~20steps).
2. HLMASK COLOR: Set the HLMASK color (Black, White, Yellow, Cyan, Green, Magenta, Red, Blue).
- D-WDR: In this mode, the brightness of a single image is
compensated using the gamma curve.
- DNR: This function reduces noise.
(Outline of DNR function)
- INITIAL: Enable user to initialize the setting on IMAGE menu.
FLIP DZOOM HLMASK D-WDR DNR INITIAL RETURN
||||||||||
|
OFF
1.0X OFF OFF MIDDLE
|
8
13
7. OSD MANUAL
6. SPECIAL
: Setting up the CAM TITLE, LANGUAGE, PRIVACY, DISPLAY, SYSTEM.
- CAM TITLE : Enable user to choose any
word in screen. (Maximum 10 letter is available)
1. A letter Choice from the screen using Menu key.
2. Enable user to move to next menu using
LEFT, RIGHT KEY in LOCATION.
3. By using UP, DOWN, LEFT, RIGHT KEY,
enable user to choose any letters in LOCATION and then get back to previous step.
4. Enable user to finish words choice and position
by using LEFT, RIGHT KEY in RETURN.
CAM TITLE
0123456789ABCDEFGHIJKLMN OPQRSTUVWXYZ!?*#$%()<>{} SPACE>> <<BACK
TITLE SET
LOCATION RETURN
- LANGUAGE: Enable user to set up an OSD language.
-> ENGLISH, RUSSIAN, SPANISH, GERMAN, FRENCH, PORTUGUESE.
:
- PRIVACY
prevent private life. (Maximum 30 point covered)
1. ZONE NO: Enable user to set up a position
from 0 to 29 area.
2. MASK MODE: Enable user to set up screen
output of chosen position.
3. X-POSITION: Mask Horizontal start position.
4. Y-POSITION: Mask Vertical start position.
5. X-SIZE: Mask Horizontal width.
6. Y-SIZE: Mask Vertical height.
7. COLOR: Set the mask color.
8. TRANSPARENCY: Set the transparency of the mask.
9. INITIAL: Enable user to initialize setting of PRIVACY MENU.
Privacy is the function that covers the some part on screen to
[ ]
SPECIAL
> CAM TITLE LANGUAGE PRIVACY MOTION DISPLAY SYSTEM INITIAL RETURN
[ TITLE LOCATION]
[U] [D] [L] [R] [M] +
PRIVACY
> ZONE NO MASK MODE X-POSITION Y-POSITION X-SIZE Y-SIZE COLOR TRANSPARENCY INITIAL RETURN
TITLE SET
[ ] ENGLISH OFF OFF [ ] [ ]
0 ON 12 2 3 3 CYN 0%
14
7. OSD MANUAL
- MOTION: Motion detection function.
1. RESOLUTION: Enable user to set up resolution
2. SENSITIVITY: Enable user to set up sensitivity.
3. WINDOW USE: Enable user to select to motion area.
4. WINDOW TONE: Enable user to area window tone.
5. X-POSITION : Window Horizontal start position.
6. Y-POSITION : Window Vertical start position.
7. X-SIZE : Window Horizontal width.
8. Y-SIZE : Window Vertical height.
9. INITIAL : Enable user to initialize setting of MOTION DETECT.
- DISPLAY : Enable user to set up a screen marking
CAM TITLE, MOTION, DZOOM.
1. CAM TITLE: Enable user to set up output in fixed CAM TITLE.
2. MOTION: Enable user to set up out put of MOTION on the screen as MOTION ON setting.
3. DZOOM: Enable user to set up output DZOOM ratio.
4. INITIAL: Enable user to initialize of DISPLAY menu.
- SYSTEM
1. DEFECT DET: White pixel detection and compensation function.
2. DOUT FORMAT: Enable user to set up digital output format (720p, 1080p).
3. DOUT FPS: Enable user to set up digital output frame rate.
4.FREQ: Enable user to set up power-frequency(50Hz, 60Hz).
5. CVBS: Enable user to set up CVBS type NTSC or PAL.
6. APPLY: Enable user to setting of SYSTEM.
When setting of FREQ and DOUT FPS are incorrect, icker or unnatural images will be caused.
The System menu is not initialized even if factory default was operated.
7.
FACTORY DEFAULT
: Enable user to reset all of the status as the factory default.
8.
EXIT
: After saving the current settings in the OSD menu and exit.
HOT KEY
To quickly switch CVBS type(NTSC or PAL), Push LEFT KEY or RIGHT KEY more than 2secends and push SET KEY.
15
MOTION
> RESOLUTION SENSITIVITY WINDOW USE WINDOW TONE X-POSITION Y-POSITION X-SIZE Y-SIZE INITIAL
DISPLAY
> CAM TITLE MOTION DZOOM INITIAL RETURN
SYSTEM
> DEFECT DET DOUT FORMAT DOUT FPS FREQ CVBS APPLY RETURN
|||
||||||||||
|
ON 1 11 3 39 28
||||||||
OFF OFF OFF
[ 」]
1080P 30 60HZ NTSC
[ ]
|
1
|
10
Loading...