KT&C KPC-HDB650M User Manual

M171-HDB650-001

HD CCTV

Digital Video Camera

OPERATION MANUAL

Thank you for choosing our high quality camera.
Befor e attempting to connect or op erate, please read and follow
these instructions.

CAUTIONS CAUTIONS

This device complies with Part 15 of the FCC
Rules. Operation is subject to the following
two conditions:

1. This device may not cause harmful interference.

2. This device must accept any interference received, including
interference that may cause undesired operation.

Note -

This equipment has been tes ted and found to comply with the lim its for a

Class A digital device, pursuant to part 15 of the FCC Rules. These limits are

designed to provide reasonable protection against harmful interference when

the equipment is opera ted in a comme rcial envi ronment. T his equip ment
generates, uses, and can radiate radio frequency energy and, if not installed

and used in accordan ce with the i nstruction manual, may ca use harmf ul

inter ference to r adio c ommunica tions. Operatio n of this equipme nt in a

residential area is likely to cause harmful interference in which case the user
will be required to correct the interference at his own expense.

WARNING -

This is a class A product. In a domestic environment this product may cause

radio interference in which case the user may be required to take adequate

measures.

Caution -

Any changes or modications in const ruction of this dev ies which are not

expressly approved by the party responsi ble for compli ance could void the
user's authority to operate the equipment.

1. A regulated DC12V 300mA power supply is recommended for use with this camera

for the best picture and the most stable operation.

An unregulated power supply can cause damage to the camera.
When an unregulated power supply is applied, the product warranty will be
roid.

2. It is recommended that the camera is used with a monitor that has a CCTV
quality 75Ω video impedance level. If your monitor is switched to high impedance

then please adjust accordingly.

3. Do not attempt to disassemble the camera to gain access to the internal
componets. Refer servicing to your dealer.

4. Never face the camera towards the sun or any bright or reective light, which

may cause smears on the picture and possible damage to the image sensor.

5. Do not remove the serial sticker for the warranty service.

6. Do not expose the camera to rain or other types of liquid.

7. The apparatus must be connected to a main socket-outlet with a protective earth

connection.

CAUTION

(Waste Electrical & Electronic Equipment)

This marking shown on the product or its literature, indicates that it should
not be disposed with other household wastes at the end of its working

life. To prevent possible harm to the environment or human health from

uncontrolled waste disposal, please separate this from other types of
wastes and recycle it responsibly to promote the sustainable reuse of

material resources. Household users should contact either the retailer

where they purchased this product, or their local government ofce, for
details of where and how they can take item for environmentally safe

recycling.

Business users should contact their supplier and check the terms and
conditions of the purchase contract.

This product should not be mixed with other commercial wastes for

disposal.

RISK OF ELECTRIC SHOCK DO NOT OPEN

CAUTION : TO REDUCE THE RISK OF ELECTRIC SHOCK, DO

NOT REMOVE COVER(OR BACK). NO USER. SERVICING TO
QUALIFED SERVICE PERSONNEL.

This symbol is intended to alert the user to the presence
of uninsulated "dangerous voltage" within the product's

enclosure that may be of sufcient mangnitude to constitute

a risk of electric shock.

This symbol is intended to alert the user to the presence of

important operating and maintenance(servicing) instruction in

the literature accompanying the appliance.

WEEE

CAUTION

COMPONENTS

HD CCTV Camera

Auto Iris Lens
Connection Plug

C-mount Adaptor Ring

Spare Screw (Machine 2x2) - 2ea

Operation Manual

NAME AND FUNCTION

FRONT

Lens Cover

C/CS RING

BACK

②

①

①. ■ MENU BUTTON
▲ UP BUTTON
▼ DOWON BUTTON
◀ LEFT BUTTON
▶ RIGHT BUTTON
②. Auto IRIS Jack

AUTO

IRIS

OSD
CONTROL

INSTALLATION

• LENS CONNECTION

Lenses are sold separatele. Lenses such as an auto iris lens,
CS-Mount lens and C-Mount lens can be used.

NOTE

• Please keep the lens clean.

• Any foreign objects and fingermarks on the lens can cause

inferior image quality in low light level conditions.

When using an auto iris lens

1.Please peel off about 8mm of the

outer skin of the auto iris lens cable.

2. Please peel off about 2mm of the

outer skin of the insulated conductor
inside the lens cable.

3. Please remove the cover of the auto iris lens connection plug and solder

the lens cable ti the connector pin in the plug.

*PIN ASSIGNMENT OF THE LENS CONNECTOR

Signal for DC + iris lens

Pin 1: DAMP­Pin 2: DAMP+
Pin 3: DRV+
Pin 4: DRV-(GND)

Signal for Video + iris lens

Pin 1: Power source: +9 DC,50mA MAX
Pin 2: N.C(Not used)
Pin 3: Video Signal:0.7Vp-p/10K ohms.
Pin 4: Shield, ground

4. Please replace the auto iris lens connection plug cover and take off the

CCD protection cap and than attach the auto iris lens to the camera by
screwing it in clockwise.

5. Please insert the connection plug that is connected to the auto iris lens cable into the

auto lens connector, which is located on the back of the camera

CS-Mount

C-Mount

Back Focus Procedure

Step 1 - Remove Lens Cover.
Step 2 - If using a C-Mount lenses it can be applied

to the camera at this time.
Step 3 - Most current lenses are CS-Mount and

require removal of the C/CS ring.
Step 4 - To remove the C/CS ring loosen but do not

remove completely the two set screws and

than remove the C/CS ring.
Step 5 - Screw on the CS-Mount lens until a good

picture is obtained and tighten the set screws.
Step 6 - Use the focus ring on the lens to obtain
a finer focusing

NOTE

- if a C-Mount lens was applied and focus could not be obtained, please try the following :

• Ensure that the lens is in face a C-Mount and not a CS-Mount.

•Check the focus adjust on the lens.

• if need be loosen the set screws and adjust the position of the lens
and C/CS ring as one unit until a good focus is obtained.

Lens Cover

Set Screw(Left Side)

CS-MOUNT ADAPTOR RING

• MONITOR CONNECTION

BNC FEMALE

HD-SDI Jack

(

)

DC12V IN
(Black)

BNC FEMALE
(2'nd Video / Yellow)

* As the connecting method varies with instruments, refer to the

manual supplied with the instrument.

* Only connect the cable when the power is turned off.
* Set the 75Ω / Hi-Z selection switch as shown below if you have an intermediate device.

HD-SDI IN

Monitor

DC12V Power Supply

OSD MANUAL

MAIN MENU 1st Sub MENU 2nd Sub MENU 3rd Sub MENU 4th Sub MENU

BRIGHTNESS 0 ~ 20

LENS(IRIS) AUTO / MANUAL

EXPOSURE

WHITE
BALANCE

D-WDR /

BLC

DNR OFF / LOW / MIDDLE / HIGH

DAY &
NIGHT

IMAGE

SPECIAL

SYSTEM

SHUTTER AUTO / MANUAL

DSS Off / X2 / X3 / X4 / X5 / X6 / X7 / X8
AGC 0 ~ 20
RESET DATA BACK / DEF
RETURN BACK / EXIT

WB MODE

SATURATION
RESET DATA BACK / DEF
RETURN BACK / EXIT

SHARPNESS 0 ~ 20
GAMMA 0.45 / 0.5 / 0.55 / 0.6 / 0.65

MIRROR OFF / ON

FLIP OFF / ON

DZOOM 1.0X / 1.1X / 1.2X / 1.3X …… 7.7X / 7.8X / 7.9X / 8.0X

DEFOG OFF / ON

LENS SHADING OFF / ON

RESET DATA BACK / DEF

RETURN BACK / EXIT

FOCUS ASSIST OFF / ON

PRIVACY OFF / ON

HLMASK OFF / ON

PATTERN OFF / ON

RESET DATA BACK / DEF

RETURN BACK / EXIT

SDI FORMAT 1080P / 720P

FRAME RATE 30(60) / 25(50)

CVBS FORMAT NTSC / PAL

APPLY OK / ON

LANGUAGE ENG / CHN / CHN(S)

SYSTEM INFO

REBOOT
RETURN BACK / EXIT

AUTO / AUTOext
/ PUSH / MANUAL

0 ~ 20

OFF / BLC /
D-WDR

AUTO/ COLOR /
B&W

AE MODE

RETURN BACK / EXIT

LEVEL

RETURN BACK / EXIT

COLOR TEMP
R-GAIN
B-GAIN
RETURN

H-POS
V-POS
H-SIZE
V-SIZE

RETURN BACK / EXIT

AGC THRES
AGC MARGIN
DELAY
RESET DATA

RETURN BACK / EXIT

MODE AUTO / MANUAL
LEVEL LOW / MIDDLE / HIGH
RETURN BACK / EXIT
WEIGHT 0% ~ 100%

RETURN BACK / EXIT

ZONE NUM 0 ~ 15

ZONE OP OFF / ON

H-POS 0 ~ 60

V-POS 0 ~ 40

H-SIZE 0 ~ 40

V-SIZE 0 ~ 40

Y LEVEL 0 ~ 10

CR LEVEL 0 ~ 10

CB LEVEL 0 ~ 10

RETURN BACK / EXIT
LEVEL 0 ~ 20

COLOR

RETURN BACK / EXIT

S/W VERSION
SET VERSION
RETURN BACK / EXIT

INDOOR / OUTDOOR
/ DEBLUR ( in Auto
Mode )

NORMAL / DEBLUR (
in Manual Mode).

1/30(25),1/60(50),1/
120(100),1/240,1/50
0,
1/1K,1/4K,1/8K,1/16
K,1/30K,1/60K

LOW / MIDDLE / HIGH

0 ~ 20

0 ~ 20

BACK / EXIT

0 ~ 20

0 ~ 20

0 ~ 20

0 ~ 20

0 ~ 20

0 ~ 20

LOW / MIDDLE / HIGH

BACK / DEF

BLK / WHI / YEL / CYN /
GRN / MAG / RED /BLU

• Function Description

0. SETUP

- EXPOSURE: Go sub menu for camera exposure control.

- WHITE BALANCE: Go sub menu for camera white balance control.

- WDR/BLC: Go sub menu for camera WDR or BLC action.

- DNR: Control noise reduction setting.

- DAY & NIGHT: Go sub menu for camera day & night control.

- IMAGE: Go sub menu for adjust image functions.

- SPECIAL: Go sub menu for special feature control.

- SYSTEM: Go sub menu for system control & information.

- Reset Data All: Reset camera’s all feature data to default value.

1. EXPOSURE

- BRIGHTNESS: Adjust image brightness value.

- LENS(IRIS): Select Lens control Type.
AE MODE: Adjust AE control Mode.

- SHUTTER : Select shutter speed control type.
LEVEL Adjust shutter speed at manual shutter mode.

- DSS Adjust digital slow shutter control level.

- AGC: Adjust max gain level for brightness control.

2. WHITE BALANCE

- WB MODE: Select white balance control mode.

AUTO: Full auto control mode in color temperature rage 2300K~10000K
AUTOext: Extened auto mode for special illumination.
PUSH: Enable fix the control setting for specific environment. Push &
release, for fix WB control setting
MANUAL: Enable WB control setting by user’s intention.

>COLOR TEMP: Select color temperature range for WB control at

>R-GAIN: Adjust red color gain for WB control at maual mode.
>B-GAIN: Adjust blue color gain for WB control at manual

- SATURATION: Adjust image brightness value.

3. WDR/BLC

- MODE: Select WDR for BLC mode.

BLC: Act in Backlight compensation mode.
D-WDR: Digital wide dynamic range control.

- BLC H-POS: Select BLC control zone vertical position.

- BLC V-POS: Select BLC control zone horizontal position.

- BLC H-SIZE: Select BLC control zone vertical size.

- BLC V-SIZE: Select BLC control zone horizontal size.

4. DNR: Reduce image’s noise

5. DAY & NIGHT

- MODE: Select DN( Digital Day & Night control ) mode.

AUTO: Camera controlled automatically to decide day or night
environment using AGC calculation data.
COLOR:
Fix to mode at day environment setting. Make video image act in color.
B&W:
Fix to mode at night environment setting. Make video image act in B/W.

> AGC THRES: Threshold level for Change Day to Night or Night to

> AGC MARGIN: Hysteresis Level for Change Day to Night or Night to

> DELAY: Delay Time for change day or Night Mode at Auto

6. IMAGE

- SHARPNESS: Adjust image sharpness level.

- GAMMA: Gamma Curve Select.

- MIRROR: Vertical Mirror Setting.

- FLIP: Horizontal flip setting.

- DZOOM: Select digital zoom magnification.

- DEFOG: Enable Defog compensation.

LEVEL: Defog compensation Level change at Auto / Manual mode.

-LENS SHADING: Enable lens shading compensation.

manual mode

mode

Day mode.

Day mode.

mode.

7. SPECIAL

- FOCUS ASSIST: Adjust image sharpness level.

- PRIVACY: Gamma Curve Select.

ZONE NUM. : Select private mask zone number. V-SIZE : Select zone vertical size.
ZONE DISP. : Select zone mask display on/off. Y LEVEL : Select mask color ( Y Level ).
H-POS : Select zone horizontal position. CR LEVEL : Select mask color ( CR Level ).
V-POS : Select zone vertical position. CB LEVEL : Select mask color ( CB Level ).
H-SIZE : Select zone horizontal size.

- HLMASK: Mask image high light area.

LEVEL : Select high light level.
COLOR : Select mask color

- PATTERN: Color bar display Enable.

8. SYSTEM

- SDI FORMAT : 1080P / 720P

- SDI FPS: 30 or 25 fps in 1080p mode.

- CVBS FORMAT : NTSC / PAL

- APPLY : Apply all video setting changed at once. Use the Set button to apply.

- SYSTEM INFO

S/W VERSION: Camera’s basic software version.
SET VERSION: Camera’s feature control setting version.

SPECIFICATIONS

Image Device 2.1 Mega Pixel, 1/3” Exmor SONY CMOS

Video output mode

Effective Pixels 1984 (H) x 1105 (V)
Unit cell size 2.8um (H) x 2.8um (V)
S/N Ratio More than 50dB
Minimum Illumination 0.1 Lux
Video Output HD-SDI / 1.0 Vp-p Composite ( 75Ω ).

Lens C / CS Mount
Shutter speed Auto / Manual selectable

D-WDR / BLC Off / BLC / D-WDR
3DNR OFF / LOW / MIDDLE / HIGH

Controllable Max Gain 23 dB
White Balance AUTO / AUTOext / PUSH / MANUAL

Digital Zoom Ratio 1X ~ 20X
Digital Slow Shutter Off, X2 ~ X8
Privacy Masking Zone 16 ea , On / Off
Day & Night Digital Day & Night
OSD Built-in
Operating Temperature 14°F~112°F (-10°C~+50°C)
Storage Temperature -4°F~158°F (-20°C~+70°C)
Power Consumption DC12V (±10%), Max. 120 mA
Dimensions (mm) 31(W) x 31(H) x 55(D)
Weight Approx.113 g

Specications and designs are subject to change for improving the functionality of this product without notice.

DIMENSIONS

720P Mode : 60 / 50 fps.

HD-SDI : 1080p@30, 1080p@25, 720p@60, 720p@50

Unit(mm)

TV Out : NTSC / PAL selectable

CS-Mount

C-Mount