KT&C KPC-HD38M User Manual

M143-HD38M-002

HDcctv
Digital Video Camera

OPERATION MANUAL

Thank you for choosing our high quality camera. Before attempting
to connect or operate, please read and follow these instructions.

CAUTIONS

Correct Disposal of This Product

(Waste Electrical & Electronic Equipment)

(Applicable in the European Union and other European
countries with separate collection systems)

This marking shown on the product or its literature, indicate that
it should not be disposed with other household wastes at the end
of its working life. To prevent possible harm to the environment or
human health from uncontrolled waste disposal, please separate
this from other types of wastes and recycle it responsibly to
promote the sustainable reuse of material resources.

This product should not be mixed with other commercial wastes

purchased this product, or their local government ofce, for details

of where and how they can take item for environmentally safe
recycling.

Business users should contact their supplier and check the terms
and conditions of the purchase contract.
Household users should contact either the retailer where they for
disposal.

RISK OF ELECTRIC SHOCK DO NOT OPEN

CAUTION : TO REDUCE THE RISK OF ELECTRIC SHOCK, DO

NOT REMOVE COVER(OR BACK). NO USER.
SERVICING TO QUALIFED SERVICE PERSONNEL.

This symbol is intended to alert the user to the presence
of uninsulated "dangerous voltage" within the product's

enclosure that may be of sufcient mangnitude to constitute a

risk of electric shock to persons.

This symbol is intended to alert the user to the presence of
important operating and maintenance(servicing) instruction in
the literature accompanying the appliance.

CAUTION

This device complies with Part 15 of the FCCRules. Operation is
subject to the following two conditions;

1. This device may not cause harmful interference.

2. This device must accept any interference received, including
interference that may cause undesired operation.

Note -

This equipment has been tested and found to comply with the limits for a Class A
digital device, pursuant to part 15 of the FCC Rules. These limits are designed to
provide reasonable protection against harmful interference when the equipment is
operated in a commercial environment. This equipment generates, uses, and can
radiate radio frequency energy and, if not installed and used in accordance with
the instruction manual, may cause harmful interference to radio communications.
Operation of this equipment in a residential area is likely to cause harmful
interference in which case the user will be required to correct the interference at
his own expense.”

WARNING -

This is a class A product. In a domestic environment this product may cause radio
interference in which case the user may be required to take adequate measures.

Caution -

Any changes or modications in construction of this devices which are not

expressly approved by the party responsible for compliance could void the user's
authority to operate the equipment.

1. A regulated DC12V 300mA power supply is recommended for use
with this camera for the best picture and the most stable operation.

An unregulated power supply can cause damage to the camera.
When unregulated power supply is applied, product warranty will
be out of subject.

2. It is recommended that the camera is used with a monitor that has a
CCTV quality 75 video impedance level. If your monitor is switched to
high impedance then please adjust accordingly.

3. Do not attempt to disassemble the camera to gain access to the
internal componets. Refer servicing to your dealer.

4. Never face the camera towards the sun or any bright or reective

light, which may cause smear on the picture and possible damage to
the CCD.

5. Do not remove the serial sticker for the warranty service.

6. Do not expose the camera to rain or other types of liquid.

7.The apparatus must be connected to a mains socket-outlet with a
protective earthing connection.

CAUTION

EQUIPMENT AND ACCESSORIES

Camera

Mounting
Bracket

Machine Screw
M2x2.5(4ea)

Screw

Operation
Manual

Service Video
Output Test Cable

Cable

• When you connect Service Video Output

Cable WDR function does not work.

• Service Video Output looks the angle of

view narrower than HD-SDI Output.

CAUTION

Tapping Screw
ø3 x 8(2ea)

DIY Cable

MOUNTING POSITION DIMENSIONSCONNECTION

OSD Control Joystick

HD-SDI

Power / RS485

Mounting

Machine Screw:
M2 x 2.5(4ea)

Camera

Bracket

❶

Tapping Screw:

ø3 x 8(2ea)

❷

❶

CAUTION !

Please start installing

in the order shown.

Service Video Connector

HD-SDI IN

Handheld

Monitor

Power Jack
(DC12V)

RS485

Unit: mm

ø23
ø14

38.5

19.4

APPROX.33

SPECIFICATION

Image Device 1/3” 2.1 Mega Pixel SONY CMOS

Pixel Size 2.8um(H) x 2.8um(V)

Effective Pixels 1984(H) x 1105(V)

Manual Shutter

29

38.5

19.4

APPROX.24

Sense-up x 2, x 3, x4

AGC 0dB ~ 23dB

White Balance AUTO / Manual / PUSH LOCK

Sensitivity 0.1 Lux

S/N Ratio More than 50dB

Video Output HD-SDI / CVBS

Day & Night Digital D&N (AUTO / COLOR / BW)

LENS Board Lens, Pinnole Lens

Dimension 38.5mm(H) x 38.5mm(V)

Weight Approx. 80g

ETC.

Power
Consumption

Operating
Temperature

Storage
Temperature

External
Control

Specifications and designs are subject to change for

improving the functionality of this product without notice.

1/30(25), 1/60(50), 1/120(100), 1/250, 1/700, 1/1K,

1/1.6K, 1/2.5K, 1/5K, 1/7K, 1/10K, 1/30K

Motion Detection, 3DNR, Mirror(H,V,H/V),

Digital Zoom, BLC, WDR, OSD(JOYSTICK)

DC12V[±10%], MAX 160mA

14˚F~122˚F (-10˚C~+50˚C)

-4˚F~140˚F (-20˚C~+60˚C)

RS-485

OSD FUNCTION DESCRIPTION

1.

EXPOSURE

- BRIGHTNESS:

Enable user to control the
image brightness (0~20steps).

- SHUTTER MODE:

Enable user to set up the
Shutter Mode.

-> AUTO, MANUAL

- SHUTTER SPEED:

Enable user to set up the
Shutter Speed.

-> 1/30(25), 1/60(50), 1/120(100), 1/250, 1/700, 1/1K,
1/1.6K, 1/2.5K, 1/5K, 1/7K, 1/10K, 1/30K.

*() is for power-frequency 50Hz.

- DSS(Digital Slow Shutter):

Enable user to set up the DSS Level. -> OFF, X2, X3, X4.

- AGC MAX:

Enable user to make imager bright to amplify the Gain (0~23dB).

Enable user to initialize the Exposure menu set up.

- INITIAL:

2.

WHITE BALANCE

Enable user to represent the
accurate white color by controlling
the R,G,B level.

- WB MODE

1. AUTO : Enable user to trace
the White Balance automatically
in the range of 2,300K~10,000K.

2. PUSH LOCK : Enable user to
fix the White Balance according
to the color temperature in the certain environment.

3. MANUAL : Enable user to sets the White Balance
according to the circumstance.

- CHROMA: Enable user to set the Color Gain(0~20steps).

- KELVIN: In the MANUAL setting of WB MODE,

enable user to set the color temperature range.

- RED GAIN: In the MANUAL setting of WB MODE,
enable user to set the RED GAIN.

EXPOSURE

> BRIGHRNESS
SHUTTER MODE
SHUTTER SPEED
DSS
AGC MAX
INITIAL
RETURN

WHITE BALANCE

> WB MODE
CHROMA
KELVIN
RED GAIN
BLUE GAIN
PUSH AUTO
INITIAL
RETURN

||||||||||

|

AUTO
– – –

OFF

23dB

AUTO

||||

– – –
– – –
– – –
– – –

- BLUE GAIN: In the MANUAL setting of WB MODE,
enable user to set the BLUE GAIN.

- PUSH AUTO: In the PUSH LOCK setting of WB MODE,
enable user to fix the White Balance in camera setting.

|

14

- INITIAL: Enable user to reset the WHITE BALANCE
menu setting.

3.

WDR/BLC

- MODE:

Enable user to set WDR/BLC

mode. -> OFF, WDR, BLC

1. WDR(Wide Dynamic Range):
Use the condition which
Image doesn’t figure out with
BLC such as place
surrounded windows and lobby.
(*The screen display may be unnatural)

2.BLC(Backlight compensation mode):
This function works for subjects in the kind of backlight conditions.

- WDR LEVEL: Enable user to set up WDR Level

- BLC OSD: Enable user to set up screen output of

chosen BLC zone.

- BLC X-POSITION: Enable user to set up Horizontal

|||||||

start position

|

7

- BLC Y-POSITION: Enable user to set up Vertical start
position

- BLC X-SIZE: Enable user to set up Horizontal size

- BLC Y-SIZE: Enable user to set up Vertical size

- INITIAL: Enable user to initialize the WDR/BLC setting.

4.

DAY&NIGHT

: Conversion of output image COLOR / BW depending on
exterior environment.

(0~20steps)

(0~20steps)

.

WDR / BLC

> MODE
WDR LEVEL
BLC OSD
BLC X - POSITION
BLC Y - POSITION
BLC X - SIZE
BLC Y - SIZE
INITIAL
RETURN

(0~4 level).

.

(0~20steps)

(0~20steps)

WDR
4
ON

|||||||

||||

||||||||

|||

||||||||||

|

||||||||||

|

.

.

- D&N MODE

1. COLOR : Enable user to fit the output
image in color.

2. B/W : Enable user to fit the
output image in B/W.
3 AUTO : Enable user to convert
to COLOR/BW automatically by
luminance element on Screen

- DWELL TIME:
In D&N MODE AUTO, enable user to set to delay time for changing
COLOR/BW(0~10sec).

- AGC THRS: The value of switching from Day to Night. In D&N MODE

|

6

|

4

AUTO, enable user to set to AGC THRS level (0~20steps).

|

7

- MARGIN: To switch from Day to Night margins.

|

10

In D&N MODE AUTO, enable user to set to MARGIN level (0~20steps).

- INITIAL: Enable user to initialize the setting in DAY&NIGHT menu.

5.

IMAGE

- SHARPNESS: Enable user to control the image sharpness(0~10steps).

- MIRROR: Sets the horizontal flip for the display output.

DAY&NIGHT

> MODE
DWELL TIME
AGC THRS
MARGIN
INITIAL
RETURN

IMAGE

> SHARPNESS

- FLIP: Sets the Vertical flip for the
displayoutput.

(OFF) (ON)

(OFF) (ON)

MIRROR

FLIP

DZOOM
HLMASK
D-WDR
DNR
INITIAL
RETURN

- DZOOM(Digital Zoom): Max. 20x Digital Zoom.

AUTO
3s

||||||||||

|

||||||||||

|

4

OFF
OFF

1X

OFF
OFF

MIDDLE

- HLMASK: This function that improves the visual recognition of license
plates and other such objects by suppressing or masking strong light
sources.

|
|

1. HLMASK LEVEL: Enable user to set HLMASK Level(0~20steps).

10

2. HLMASK COLOR: Set the HLMASK color

10

(Black, White, Yellow, Cyan, Green, Magenta, Red, Blue).

- D-WDR: In this mode, the brightness of a single image is

compensated using the gamma curve.

- DNR: This function reduces noise.

- INITIAL: Enable user to initialize the setting on IMAGE menu.

(Outline of DNR function)

6.

SPECIAL

: Setting up the CAM TITLE,
LANGUAGE, PRIVACY,COMM
MOTION, DISPLAY, SYSTEM.

- CAM TITLE : Enable user to choose
any word in screen.

(Maximum 10 letter is available)

1. A letter Choice from the screen

using Menu key.

2. Enable user to move to next

menu using LEFT, RIGHT KEY

in LOCATION.

3. By using UP, DOWN, LEFT,

RIGHT KEY, enable user to
choose any letters in LOCATION
and then get back to previous step.

SPECIAL

> CAM TITLE
LANGUAGE
COMM ADJUST
PRIVACY
MOTION
DISPLAY
SYSTEM
INITIAL
RETURN

CAM TITLE

0123456789ABCDEFGHIJKLMN

OPQRSTUVWXYZ!?*#$%()<>{}
SPACE>> <<BACK

TITLE SET

LOCATION
RETURN

[ ]
ENGLISH
[ ]

OFF
OFF

[ ]
[ ]

[ ]

4. Enable user to finish words
choice and position by using

LEFT, RIGHT KEY in RETURN

- LANGUAGE: Enable user to set up an OSD language

-> ENGLISH, RUSSIAN, SPANISH, GERMAN, FRENCH, PORTUGUESE.

- COMM ADJUST

set up CAMERA ID, BAUDRATE.

1. CAM ID: Enable user to set up

Camera ID (1~255).

2. BAUDRATE: A communication speed to

communicate with external device.
(2400, 4800, 9600, 19200, 38400,
57600, 115200)

3. APPLY: Enable user to setting of

Communication

- PRIVACY

covers the some part on screen to
prevent private life.
(Maximum 30 point covered)

1. ZONE NO : Enable user to set up a

position from 0 to 29 area.

2. MASK MODE: Enable user to set up

screen output of chosen position.

3. X-POSITION : Mask Horizontal

start position.

4. Y-POSITION : Mask Vertical start position.

5. X-SIZE : Mask Horizontal width.

6. Y-SIZE : Mask Vertical height.

7. COLOR : Set the mask color.

8. TRANSPARENCY : Set the transparency of the mask.

9. INITIAL : Enable user to initialize setting of PRIVACY MENU.

: Enable user to

: Privacy is the function that

[ TITLE LOCATION]

TITLE SET

[U] [D] [L] [R] [M] +

COMM ADJUST

> CAM ID
BAUDRATE
APPLY
RETURN

1
2400BPS

[ ]

PRIVACY

> ZONE NO
MASK MODE
X-POSITION
Y-POSITION
X-SIZE
Y-SIZE
COLOR
TRANSPARENCY
INITIAL
RETURN

0
ON
12
2
3
3
CYN
0%

- MOTION:

1. RESOLUTION:
Enable user to set up resolution

2. SENSITIVITY:
Enable user to set up sensitivity.

3. WINDOW USE: Enable user
to select to motion area.

4. WINDOW TONE :
Enable user to area window tone.

5. X-POSITION : Window Horizontal
start position.

6. Y-POSITION : Window Vertical start position.

7. X-SIZE : Window Horizontal width.

8. Y-SIZE : Window Vertical height.

9. INITIAL : Enable user to initialize setting of MOTION DETECT.

- DISPLAY :

Enable user to set up a screen marking
of CAM ID, CAM TITLE, MOTION, DZOOM.

1. CAM ID: Enable user to set up
ID for RS485.

2. CAM TITLE: Enable user to set up
output in fixed CAM TITLE.

3. MOTION: Enable user to set up out put
of MOTION on the screen as MOTION
ON setting.

4. DZOOM: Enable user to set up output
DZOOM ratio.

5. INITIAL: Enable user to initialize of DISPLAY menu.

- SYSTEM

1. DEFECT DET: White pixel detection and

compensation function.

2. DOUT FORMAT: Enable user to set up

digital output format (720p, 1080p).

3. DOUT FPS: Enable user to set up

digital output frame rate.

4.FREQ: Enable user to set up

power-frequency(50Hz, 60Hz).

5. CVBS: Enable user to set up
CVBS type NTSC or PAL.

6.APPLY: Enable user to setting of SYSTEM.

Motion detection function.

MOTION

> RESOLUTION
SENSITIVITY
WINDOW USE
WINDOW TONE
X-POSITION
Y-POSITION
X-SIZE
Y-SIZE
INITIAL

DISPLAY

> CAM ID
CAM TITLE
MOTION
DZOOM
INITIAL
RETURN

SYSTEM

> DEFECT DET
DOUT FORMAT
DOUT FPS
FREQ

CVBS
APPLY
RETURN

|||

||||||||||

|

ON
1
11
3
39
28

||||||||

OFF
OFF
OFF
OFF

[ 」]

1080P
30
60HZ
NTSC

[ ]

7.

FACTORY DEFAULT

: Enable user to reset all of the status as the factory default.

|

0

|

10

8.

EXIT

: After saving the current settings in the OSD menu and exit.

HOT KEY

To quickly switch CVBS type(NTSC or PAL), Push LEFT KEY or RIGHT

KEY more than 2secends and push SET KEY.

Pelco “D” Protocol Commands

Most widely used Commands

MENU 1 : Pelco Keyboard Menu On / Off [95(=0x5F) + Pattern]

MENU 2 : V/D Keyboard Menu On / Off [Set Preset + 98(=0x62)]
MENU 3,4 : Another Menu On / Off [Go To Preset + 95(=0x5F) or 96(=0x60)]

CamID: 0x00 ~0xFF

ChkSum: The Check Sum is the 8 bit (modulo256) sum of the payload bytes
(BYTE2 - BYTE6) in the command.

- TELE = UP KEY

- WIDE = DOWN KEY

- NEAR = LEFT KEY

- FAR = RIGHT KEY

- MENU = SELECT KEY

BYTE1 BYTE2 BYTE3 BYTE4 BYTE5 BYTE6 BYTE7

0xFF CamID 0x00 0x20 0x00 0x00 ChkSum

TELE

0xFF CamID 0x00 0x40 0x00 0x00 ChkSum

WIDE

0xFF CamID 0x01 0x00 0x00 0x00 ChkSum

NEAR

0xFF CamID 0x00 0x00 0x00 0x00 ChkSum

FAR

MENU 1

MENU 2

MENU 3

MENU 4

0xFF CamID 0x00 0x23 0x00 0x5F ChkSum

0xFF CamID 0x00 0x03 0x00 0x62 ChkSum

0xFF CamID 0x00 0x07 0x00 0x5F ChkSum

0xFF CamID 0x00 0x07 0x00 0x60 ChkSum