KT&C KPC-EJ230NU User Manual

M122-EJ230-002

HIGH PERFORMANCE

BULLET CAMERA

OPERATION MANUAL

Thank you for choosing our high quality camera. Before
attempting to connect or operate, please read and follow
these instructions.

CAUTIONS

These servicing instructions are for use by qualied service personnel only.

To reduce the risk of electric shock do not perform any servicing other than

that contained in the operating instructions unless you are qualied to do so.

Use Class 2 Power Supply Only.

This device complies with Part 15 of the FCC Rules.
Operation is subject to the following two conditions;

1. This device may not cause harmful interference.

2. This device must accept any interference received,
including interference that may cause undesired operation.

Note -

This equipment has been tested and found to comply with the limits for a
Class A digital device, pursuant to part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference when
the equipment is operated in a commercial environment. This equipment
generates, uses, and can radiate radio frequency energy and, if not installed
and used in accordance with the instruction manual, may cause harmful
interference to radio communications. Operation of this equipment in a
residential area is likely to cause harmful interference in which case the user
will be required to correct the interference at his own expense.”

WARNING -

This is a class A product. In a domestic environment this product may cause
radio interference in which case the user may be required to take adequate
measures.

Caution -

Any changes or modications in construction of this devies which are not

expressly approved by the party responsible for compliance could void the
user’s authority to operate the equipment.

1. A regulated DC12V 300mA power supply is recommended for use with
this camera for the best picture and the most stable operation.

An unregulated power supply can cause damage to the camera. When
unregulated power supply is applied,
product warranty will be out of subject.

2. It is recommended that the camera is used with a monitor that has a
CCTV quality 75 video impedance level. If your monitor is switched to high
impedance then please adjust accordingly.

3. Do not attempt to disassemble the camera to gain access to the internal
componets. Refer servicing to your dealer.

4. Never face the camera towards the sun or any bright or reective light,

which may cause smear on the picture and possible damage to the CCD.

5. Do not remove the serial sticker for the warranty service.

CAUTION

Correct Disposal of This Product

(Waste Electrical & Electronic Equipment)

(Applicable in the European Union and other European
countries with separate collection systems)

This marking shown on the product or its literature, indicate that
it should not be disposed with other household wastes at the end
of its working life. To prevent possible harm to the environment or
human health from uncontrolled waste disposal, please separate
this from other types of wastes and recycle it responsibly to promote
the sustainable reuse of material resources.

This product should not be mixed with other commercial wastes

purchased this product, or their local government ofce, for details

of where and how they can take item for environmentally safe
recycling.

Business users should contact their supplier and check the terms
and conditions of the purchase contract.
Household users should contact either the retailer where they for
disposal.

CAUTION : TO REDUCE THE RISK OF ELECTRIC SHOCK, DO
NOT REMOVE COVER(OR BACK). NO USER. SERVICING
TO QUALIFED SERVICE PERSONNEL.

RISK OF ELECTRIC SHOCK DO NOT OPEN

This symbol is intended to alert the user to the presence
of uninsulated "dangerous voltage" within the product's

enclosure that may be of sufcient mangnitude to constitute

a risk of electric shock to persons.

This symbol is intended to alert the user to the presence of
important operating and maintenance(servicing) instruction in
the literature accompanying the appliance.

CAUTION

IMPORTANT SAFETY INSTRUCTION

1) Read these instructions.

2) Keep these instructions.

3) Heed all warnings.

4) Follow all instructions.

5) Do not use this apparatus near water.

6) Clean only with dry cloth.

7) Do not block any ventilation openings. Install in accordance
with the manufacturer’s instructions.

8) Do not install near any heat sources such as radiators, heat

registers,stoves, or other apparatus (including ampliers)

that produce heat.

9) Do not defeat the safety purpose of the polarized or
grounding- type plug. A polarized plug has two blades with one
wider than the other. A grounding type plug has two blades and
a third grounding prong. The wide blade or the third prong are

provided for your safety. If the provided plug does not t into your

outlet, consult an electrician for replacement of the obsolete
outlet.

10) Protect the power cord from being walked on or pinched
particularly at plugs, convenience receptacles, and the point
where they exit from the apparatus.

11) Only use attachments/accessories specied by the

manufacturer.

12) Use only with the cart, stand, tripod, bracket, or table specied

by the manufacturer, or sold with the apparatus.
When a cart is used, use caution when moving
the cart/apparatus combination to avoid injury
from tip-over.

13) Unplug this apparatus during lightning storms or when unused

for long periods of time.

14) Refer all servicing to qualied service personnel. Servicing is

required when the apparatus has been damaged in any way,
such as power-supply cord or plug is damaged, liquid has been
spilled or objects have fallen into the apparatus, the apparatus
has been exposed to rain or moisture, does not operate
normally, or has been dropped.

COMPONENTS

Bullet
Camera

Mounting
Bracket

Screw 3ea

Operation
Manual

MOUNTING POSITION

(A'ssy View)

CONNECTION

VIDEO IN

Yellow (Video Out)
Black (GND Common)
Red ( DC +12V IN)

LEAD WIRE CONNECTION (STANDARD)

DC12V

(BLACK)

BNC FEMALE

DIY CABLE CONNECTION

When you install the camera, please glue up the end of
cable to keep it stable in order to protect the camera from
the humidity problems.

DC12V POWER SUPPLY

DC12V POWER SUPPLY

VIDEO IN

Mount Guide

TV MONITOR

TV MONITOR

DIMENSIONS

Unit(mm)

90.7

75.2

16.8

50

26.6

Ф

OSD MENU STRUCTURE

1/4"-20 UNC

10.5

Joy-Stick

Control Rubber

78.1

62.6

23

Ф

Joy-Stick

Control Rubber

77.9

62.4

23

Ф

Joy-Stick

Control Rubber

81.9

66.4

23

Ф

Joy-Stick

Control Rubber

78.7

63.2

23

Ф

Joy-Stick

Control Rubber

1/4"-20UNC

28.6

3-Ф

3.2

112.5

40

80.75

1/4"-20 UNC

23

Ф

24.8

1/4"-20UNC

MAIN MENU 1st Sub MENU 2nd Sub MENU 3rd Sub MENU 4th Sub MENU

HIGH LUMINANCE

AUTO

SHUTTER/AGC

MANUAL

ATW

PUSH

WHITE BAL

USER1

USER2

ANTI CR

MANUAL

BACK LIGHT OFF,BLC,HLC

PIC ADJUST

ATR

PUSH LOCK

MIRROR OFF,ON
BRIGHTNESS (000 ~ 255)
CONTRAST (000 ~ 255)
SHARPNESS (000 ~ 255)
HUE (000 ~ 255)
GAIN (000 ~ 255)
RETURN

ON

OFF

LOW LUMINANCE

RETURN
MODE SHUT+AGC

SHUTTER

AGC 6,12,18,24,30,36,42,44.8
RETURN
SPEED
DELAY CNT (000 ~ 255)
ATW FRAME x0.50,x1.00,x1.50,x2.00
ENVIRONMENT INDOOR,OUTDOOR
RETURN

B-GAIN (000 ~ 255)
R-GAIN (000 ~ 255)
RETURN
B-GAIN (000 ~ 255)
R-GAIN (000 ~ 255)
RETURN

LEVEL
RETURN

LUMINANCE LOW,MID,HIGH

CONTRAST

RETURN

DETECT SENS (000 ~ 255)

BLOCK DISP

MONITOR AREA ON,OFF

MOTION DET

NEXT
EXIT
SAVE ALL

ON

OFF

AREA SEL

RETURN

UP

LEFT

MODE SHUT
BRIGHTNESS (000 ~ 255)
MODE AGC,OFF
BRIGHTNESS x0.25,x0.50,x0.75,x1.00

1/50(PAL),1/100(NTSC)
1/60(NTSC),1/120(PAL)
1/250,1/500,1/1000
1/2000,1/4000,1/10000

(000 ~ 255)

27 ~ 105

LOW,MIDLOW,MID,
MIDHIGH,HIGH

OFF,ON,ENABLE
(CONTROLER)

1/4, 2/4, 3/4, 4/4

TOP

BOTTOM

LEFT

RIGHT

MENU

(SELECTION KEY)

NTSC:(000 ~ 244)
PAL:(000 ~ 288)

NTSC:(000 ~ 244)
PAL:(000 ~ 288)

NTSC:(000 ~ 474)
PAL:(000 ~ 468)

NTSC:(000 ~ 474)
PAL:(000 ~ 468)

RIGHT

73

DOWN

When the OSD control, Rubber
Please adjust the side to put a

nger deep.

MAIN MENU 1st Sub MENU 2nd Sub MENU 3rd Sub MENU 4th Sub MENU

AREA SEL

PRIVACY

DAY&NIGHT

NR

CAMERA ID

LANGUAGE ENGLISH /
CAMERA

RESET
BACK
EXIT
SAVE ALL

*Important Note :

- Any changes made to the camera settings must be saved prior to exiting the OSD menu.
Else all changes will be discarded.

ON

COLOR (1 ~ 8)
TRANSP 0.00, 0.50, 0.75, 1.00
MOSAIC OFF,ON

OFF
COLOR
B/W BURST OFF,ON

AUTO

NR MODE OFF,Y,C,Y/C
Y LEVEL (000 ~ 015)
C LEVEL (000 ~ 015)
RETURN

ON

OFF

RETURN

BURST OFF,ON
DELAY CNT 0 ~ 255
DAY -> NIGHT 0 ~ 255
NIGHT ->DAY 0 ~ 255

EDIT MODE
RETURN

日本語

/ DEUTSCH / FRANCAIS /

1/4, 2/4, 3/4, 4/4

TOP

BOTTOM

LEFT

RIGHT

Русский

NTSC:(000 ~ 244)
PAL:(000 ~ 288)

NTSC:(000 ~ 244)
PAL:(000 ~ 288)

NTSC:(000 ~ 474)
PAL:(000 ~ 468)

NTSC:(000 ~ 474)
PAL:(000 ~ 468)

/ PORTUGUÊS / ESPAÑOL /

中文

SPECIFICATION

Signal Format NTSC PAL
Image Device 1/3” 960H SONY EXview HAD CCD II
Scanning System 2 : 1 Interlace
H Resolution. 750TV Lines
Scanning Frequency 15.734KHz(H), 59.94Hz(V) 15.625KHz(H), 50Hz(V)
Total Pixels 1020(H) X 508(V) 1020(H) X 596(V)
Effective Pixels 976(H) X 494(V)
Electronic Shutter 1/60 ~ 1/100,000 sec 1/50 ~ 1/100,000 sec
S/N Ratio More than 50dB(AGC OFF)
Min. Illumination 0.1Lux
Sync System Internal
Gamma r= 0.45
Video Output 1.0 Vp-p Composite (75Ω)
OSD Built in (Inner Key / Joystick)
BLC OFF / BLC / HLC
White Balance ATW / PUSH / USER1 / USER2 / ANTI CR / MANUAL / PUSH-LOCK
2DNR OFF / ON (Level adjustable)
ATR OFF / ON (Level adjustable)
Function MIRROR / BRIGHTNESS / CONTRAST / SHARPNESS / HUE / GAIN
Privacy Masking 4 Zones
Motion Detection 4 Zones
Day & Night Digital D&N (Option)
Lens Board Lens, Pinhole Lens. Varifocal Lens

Language

Operating Temperature 14°F~122°F (-10°C~+50°C)
Storage Temperature -4°F~140°F (-20°C~+60°C)
Humidity Less than 80%
Power Consumption DC12V ±10% Max. 83mA
Weight Approx. 68g
Dimension(mm) 23.0Ø x 75.2mm

ENGLISH / JAPANESE / GERMAN / FRENCH / RUSSIAN / PORTUGUESE / SPANISH /

CHANESE

Specications and designs are subject to change for improving the functionality of this product without notice.

976(H) X 582(V)