KT&C KPC-DE100NUV7 User Manual

HIGH RESOLUTION

DOME CAMERA

OPERATION MANUAL

M105-DE100-005

Thank you for choosing our high quality camera.
Before attempting to connect or operate, please read and follow these instructions.

CAUTION

These servicing instructions are for use by qualied service personnel only.
To reduce the risk of electric shock do not perform any servicing o ther than
that contained in the operating instructions unless you are qualied to do so.

Use Class 2 Power Supply Only

2

CONTENTS

1. CAUTIONS

2. IMPORTANT SAFETY INSTRUCTIONS

3. FEATURES

4. EQUIPMENT AND ACCESSORIES

5. OVERVIEW AND FUNCTION

6. INSTALLATION

7. CONNECTION

8. DIMENSIONS

9. SPECIFICATION

10. OSD MENU STRUCTURE

3

1. CAUTIONS

This device complies with Part 15 of the FCC Rules.
Operation is subject to the following two conditions:

1. This device may not cause harmful interference.

2. This device must accept any interference received, including
interference that may cause undesired operation.

Note

This equipment has been tested and found to comply with limits for a Class B digital
device, pursuant to part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a residential installation.
This equipment generates, uses, and can radiate radio communications.
However, there is no guarantee that interference will not occur in a particular
installation. If this equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and receiver.

• Connect the equipment into an outlet on a circuit different from that to which the

receiver is connected.

• Consult the dealer or an experienced radio / tv technician for help.

Caution

Any changes or modications in construction of this device which are not expressly

approved by the party responsible for compliance could void the user’s authority to
operate the equipment.

1. A regulated DC12V 1A power supply is recommended for use with this camera
for the best picture and the most stable operation.
An unregulated power supply can cause damage to the camera.

When unregulated power supply is applied, product warranty will be out of subject.

2. It is recommended that the camera is used with a monitor that has a CCTV quality
75 video impedance level.
If your monitor is switched to high impedance then please adjust accordingly.

3. Do not attempt to disassemble the camera to gain access to the internal componets.
Refer servicing to your dealer.

4. Never face the camera towards the sun or any bright or reective light, which may

cause smear on the picture and possible damage to the CCD.

5. Do not remove the serial sticker for the warranty service.

6. Do not expose the camera to rain or other types of liquid.

7. The apparatus must be connected to a mains socket-outlet with a protective earthing
connection.

4

1. CAUTIONS

(Waste Electrical & Electronic Equipment)

WEEE

This marking shown on the product or its literature, indicates that it should
not be disposed with other household wastes at the end of its working life. To
prevent possible harm to the environment or human health from uncontrolled
waste disposal, please separate this from other types of wastes and recycle it
responsibly to promote the sustainable reuse of material resources. Household
users should contact either the retailer where they purchased this product, or

their local government ofce, for details of where and how they can take item

for environmentally safe recycling.
Business users should contact their supplier and check the terms and
conditions of the purchase contract.

This product should not be mixed with other commercial wastes for disposal.

CAUTION

RISK OF ELECTRIC SHOCK DO NOT OPEN

CAUTION:

TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT
REMOVE COVER (OR BACK). NO USER SERVICEABLE
PARTS INSIDE. REFER SERVICING TO QUALIFIED
SERVICE PERSONNEL

This symbol is intended to alert the user to the presence
of un-insulated “dangerous voltage” within the product’s

enclosure that may be of sufcient magnitude to constitute a

risk of electric shock.

This symbol is intended to alert the user to the presence of
important operating and maintenance (servicing) instructions
in the literature accompanying the appliance.

5

2. IMPORTANT SAFETY INSTRUCTIONS

1) Read these instructions.

2) Keep these instructions.

3) Heed all warnings.

4) Follow all instructions.

5) Do not use this apparatus near water.

6) Clean only with dry cloth.

7) Do not block any ventilation openings. Install in accordance
with the manufacturer’s instructions.

8) Do not install near any heat sources such as radiators, heat registers,

stoves, or other apparatus (including ampliers) that produce heat.

9) Do not defeat the safety purpose of the polarized or grounding-type plug. A
polarized plug has two blades with one wider than the other. A grounding type
plug has two blades and a third grounding prong. The wide blade or the third

prong are provided for your safety. If the provided plug does not t into your

outlet, consult an electrician for replacement of the obsolete outlet.

10) Protect the power cord from being walked on or pinched particularly at plugs,

convenience receptacles, and the point where they exit from the apparatus.

11) Only use attachments/accessories specied by the manufacturer.

12) Use only with the cart, stand, tripod, bracket, or table specied by

the manufacturer, or sold with the apparatus. When a cart is used,

use caution when moving the cart/apparatus combination to

avoid injury from tip-over.

13) Unplug this apparatus during lightning storms or when unused for long

periods of time.

14) Refer all servicing to qualied service personnel. Servicing is required when

the apparatus has been damaged in any way, such as power-supply cord
or plug is damaged, liquid has been spilled or objects have fallen into the

apparatus, the apparatus has been exposed to rain or moisture, does not

operate normally, or has been dropped.

6

3. FEATURES

• 1/3 960H SONY EXview HAD CCD II

• High Resolution of 700TV Lines

• OSD Function

• Multi Language

(ENGLISH / JAPANESE / GERMAN / FRENCH / RUSSIAN / PORTUGUESE / SPANISH / CHINESE)

• 2DNR

• Privacy Zone

• Motion Detect

• DC12V / AC24V Dual Voltage

• ATR(Adaptive Tone-curve Reproduction / Digital WDR)

The function provides gradation compensation to improve the contrast of subjects both
low-luminance areas and high luminance areas exist in the same picture

• 3-Axis Gimbal

Pan Rotation Tilt Rotation Horizontal Rotation

• Service Video connector

The Se rvice Video Connector also provides the installer with an easy way o f con guring the

camera.

7

4. EQUIPMENT AND ACCESSORIES

1 DOME CAMERA

2 VIDEO OUTPUT TEST CABLE

3 OPERATION MANUAL

4 SCREW - 3ea

5 TEMPLATE

8

5. OVERVIEW AND FUNCTION

• Name (LED Type)

Service Video
Connector

• Name (Standard)

OSD Joystick

IR LED 30ea

• CONTROL FUNCTION

(OSD JOYSTICK)

LEFT

Photo Cell

3-Axis

Gimbal

DOWN

3-Axis

Gimbal

UP

RIGHT

Service Video
Connector

OSD Joystick

9

6. INSTALLATION

4

5

1

Lens Zoom Knob

2

3

7 6

Lens Focus Knob

Separate LED Cover (Sunshield Cover)

and adjust LENS ZOOM / FOCUS KNOB

After setting the LENS, assemble the
LED Cover (Sunshield Cover).

70˚ 70˚

Standard Type

LED Type

NO PART NAME

1 Mount Guide

2 Housing Bottom
3 Holder Panning
4 Holder Tlit

5 Holder Rotate

6 Sunshield Cover
7 Led Cover

8 Housing Top

9 Dome Cover

8

9

10

7. CONNECTION

• DUAL(DC 12V/AC24V)

DC 12V / AC 24V

DUAL POWER SUPPLY

VIDEO IN

BNC FEMALE
VIDEO

• DC 12V

DC 12V
POWER SUPPLY

VIDEO IN

BNC FEMALE
VIDEO

When you install the camera, please glue up the end of cable to
keep it stable in order to protect the camera from the humidity problems.

11

8. DIMENSIONS

Unit : mm

Ø100

96.9

45

Ø135

Ø108.5

12

9. SPECIFICATION

Signal Format NTSC PAL
Image Device 1/3˝ 960H SONY EXview HAD CCD II
Scanning System 2:1 Interlace
H.Resolution 700TV Lines
Scanning Frequency H:15.734KHz, V:59.94Hz H:15.625KHz, V:50Hz

Total Pixels 1020(H) X 508(V) 1020(H) X 596(V)
Effective Pixels 976(H) X 494(V) 976(H) X 582(V)
Electronic Shutter Speed 1/60 sec 1/50 sec
S/N Ratio More than 50dB(AGC Off)

Gamma r=0.45
Min. Illumination COLOR : 0.05Lux/F1.2, BW : 0.02 Lux/F1.2
Sync System Internal
Video Output 1.0 Vp-p Composite(75Ω)
OSD Built in (Inner Key / Joystick)
BLC OFF / BLC / HLC
White Balance ATW / PUSH / USER1 / USER2 / ANTI CR / MANUAL / PUSH-LOCK
2DNR OFF / ON (Level adjustable)
ATR OFF / ON (Level adjustable)
Function MIRROR / BRIGHTNESS / CONTRAST / SHARPNESS / HUE / GAIN
Privacy Masking 4 Zones
Motion Detection 4 Zones
Day & Night AUTO

Language
Power

Consumption
Operating Temperature -10℃ ~ +50
Storage Temperature -20℃ ~ +60
Operating Humidity Less than 80%
Options Dual Power
Weight Approx. 343g
Dimension(mm) 136.4(Φ) x 95.3(mm)

DC12V DC 12V, (±10%) Max.120mA
Dual DC 12V, (±10%) Max.150mA / AC 24V, (±10%) Max. 2.3W

LED TYPE

Power
Consumption

Min. Illumination 0 Lux (IR LED ON)
IR LED 850nm, 30ea
IR Beam Range Up to 30M
IR LED Operation On : 1 Lux, Off : 3 Lux

Specifications and designs are subject to change for improving the functionality of this product without notice.

DC12V DC 12V, (±10%) Max. 320mA
Dual DC 12V, (±10%) Max 390mA / AC 24V, (±10%) Max. 4.8W

ENGLISH / JAPANESE / GERMAN / FRENCH / RUSSIAN/

PORTUGUESE / SPANISH / CHINESE

℃

℃

13

10. OSD MENU STRUCTURE

MAIN

MENU

LENS

1st Sub

MENU

MANUAL

AUTO

AUTO

SHUTTER

/ AGC

MANUAL

ATW

PUSH

USER1

WHITE
BAL

USER2

ANTI CR
MANUAL
PUSH LOCK

BACK LIGHT OFF,BLC,HLC

MIRROR
BRIGHTNESS
CONTRAST

PIC

SHARPNESS

ADJUST

HUE
GAIN
RETURN

ON

ATR

OFF

*SHUT+IRIS:
*Auto Iris(Default): The Shutter stays at the manually selected value and only the Mechanical Iris adjusts to brightness.

Both the Shutter and the Mechanical Iris are automatically adjusted according to brightness.

2nd Sub

MENU

TYPE DC
MODE AUTO,OPEN,CLOSE
SPEED (000 ~ 255)
RETURN

HIGH LUMINANCE

LOW LUMINANCE

RETURN
MODE SHUT+AGC

SHUTTER

AGC 6,12,18,24,30,36,42,44.8
RETURN
SPEED (000 ~ 255)
DELAY CNT (000 ~ 255)
ATW FRAME x0.50,x1.00,x1.50,x2.00
ENVIRONMENT INDOOR,OUTDOOR
RETURN

B-GAIN (000 ~ 255)
R-GAIN (000 ~ 255)
RETURN
B-GAIN (000 ~ 255)
R-GAIN (000 ~ 255)
RETURN

LEVEL 24 ~ 103
RETURN

OFF,ON
(000 ~ 255)
(000 ~ 255)
(000 ~ 255)
(000 ~ 255)
(000 ~ 255)

LUMINANCE LOW,MID,HIGH
CONTRAST LOW,MIDLOW,MID,MIDHIGH,HIGH
RETURN

3rd Sub

MENU

MODE SHUT,AUTO IRIS, SHUT+AUTO IRIS
BRIGHTNESS (000 ~ 255)
MODE AGC,OFF
BRIGHTNESS x0.25,x0.50,x0.75,x1.00

1/50(PAL),1/100(NTSC)
1/60(NTSC),1/120(PAL)
1/250,1/500,1/1000
1/2000,1/4000,1/10000

14

4th Sub

MENU

10. OSD MENU STRUCTURE

MAIN

MENU

MOTION
DET

NEXT
EXIT
SAVE ALL

PRIVACY

NR

CAMERA
ID

LANGUAGE ENGLISH, 日本語, DEUTSCH, FRANCAIS,
CAMERA

RESET
BACK
EXIT
SAVE ALL

*Important Note :

- Any changes made to the camera settings must be saved prior to exiting the OSD menu.

Else all changes will be discarded.

- By changing the lens option in the OSD from MANUAL to AUTO will automatically change the

SHUTTER/AGC setting from AUTO IRIS to SHUT+AUTO IRIS.(Default:AUTO IRIS)

1st Sub

MENU

ON

OFF

ON

OFF
NR MODE OFF,Y,C,Y/C
C LEVEL (000 ~ 015)
Y LEVEL (000 ~ 015)
RETURN
ON EDIT MODE

OFF

2nd Sub

MENU

DETECT SENSE
BLOCK DISP
MONITOR AREA

AREA SEL

RETURN

AREA SEL

COLOR
TRANSP
MOSAIC
RETURN

RETURN

3rd Sub

MENU

(000 ~ 127)
OFF,ON,ENABLE (CONTROLER)
ON,OFF

1/4, 2/4, 3/4, 4/4

TOP NTSC:(000 ~ 244) / PAL: (000 ~ 288)
BOTTOM NTSC:(000 ~ 244) / PAL: (000 ~ 288)
LEFT NTSC:(000 ~ 474) / PAL: (000 ~ 468)
RIGHT NTSC:(000 ~ 474) / PAL: (000 ~ 468)

1/4, 2/4, 3/4, 4/4

TOP NTSC:(000 ~ 244) / PAL: (000 ~ 288)
BOTTOM NTSC:(000 ~ 244) / PAL: (000 ~ 288)
LEFT NTSC:(000 ~ 474) / PAL: (000 ~ 468)
RIGHT NTSC:(000 ~ 474) / PAL: (000 ~ 468)
(1 ~ 8)

0.00, 0.50, 0.75, 1.00
OFF,ON

Русский,

PORTUGUÊS, ESPAÑOL, 中文

4th Sub

MENU

15