KT&C KNC-VNi120HD User Manual

M121-VDi100/120HD-001

Megapixel Network Camera

KNC-VDi100HD/KNC-VNi100HD KNC-VDi120HD/KNC-VNi120HD

Installation Guide

3. Product Description

Description and function

LED Type:

KNC-VNi100HD, KNC-VNi120HD

❶

❷

❸

❹

Standard Type:

KNC-VDi100HD, KNC-VDi120HD

❷

❸

❹

4. Install the hardware

KNC-VDi100HD, KNC-VNi100HD, KNC-VDi120HD, KNC-VNi120HD are designed to be installed using a template as shown below.

1. Template – To mount the camera.

2. Plastic Anchors(3ea) – To secure the camera to the template.

3. Screws(3ea) - To secure the camera to the template.

4. Screws(3ea) – Screws to secure the camera case

Lens Zoom Knob

Lens Focus Knob

NOTE

When using the camera

without LED take off the rubber.

❶

❷

❸

Table of Contents

1.INTRODUCTION

2.PACKAGE CONTENTS

3.PRODUCT DESCRIPTION

4.INSTALL THE HARDWARE

5.ASSIGN AN IP ADDRESS

6.TERMINAL BLOCK CONNECTORS

1. Introduction

KNC-VDi100HD,KNC-VNi100HD,KNC-VDi120HD,KNC-VNi120HD Installation Guide

This installation guide provides instructions for installing the Network Camera on your network. For all other aspects of using the product, please see the User’s Manual, available on the CD included in this package, or from http://www.ktnc.co.kr

Installation steps

1. Check the package contents against the list below.

2. Product description.

3. Install the hardware.

4. Set an IP address.

5. Set the admin and user ID and password, See User’s Manual.

Important!

This product must be used in compliance with local laws and regulations.

❺

❻

❼

❽

1. Infrared LED – These LEDs emit infra red radiations.

2. Cooling fan – Cools the components and prevents them from overheating.

3. Service Video Connector – Outputs video to the monitor.

4. Reset Button – Resets the product to the factory default settings.

5. Power Input(DC12V) – Connect DC 12V power.

6. Digital Input – Connect signal from external sensor.

7. Digital Output – Connect signal to external alarm. (Max. current - DC 12V, 70mA)

Digital Input Digital Output

8. Network Connector –

The Network Camera connects to the network via a standard network cable, and automatically detects the speed of the local network segment (10BaseT/100BaseTX Ethernet). PoE Supported

3-Axis Gimbal

Connection

❹

1. Connect the camera to the network using a UTP cable (CAT.5), Power can be supplied via the network cable (PoE)

2. Connect DC 12V to the power terminal. This is not necessary if the Network Camera is connected to PoE hub or midspan.

3. Check that the indicator LEDs indicates the correct conditions.

4. Connect the analog monitor to the service video connector for adjusting focus and press and quickly release the reset switch for focus assistant mode. Then you can select normal view or focus view mode using the reset switch.

Caution: When you use focus assistant mode, “Focus View” mode is recommended for more exact focus. Caution: Focus assistant mode will be automatically exited after 3 minutes for normal operation.

Dimensions

2. Package Contents

Network Camera Video Output Test Cable Software CD

Installation Guide Template

When using Wall Mount Bracket

Screws / Plastic anchors /

Wrench / RJ45 Coupler

Pan Rotation

Tilting angle

CAUTION panning(Pan + Horizontal) the bracket in excess of 1 rotations in one direction

may cause damage to the cable.

Tilt Rotation

Horizontal Rotation

Ø112.8

Ø107

Ø124

123.4

71.5

Ø151

5. Assign an IP address

To make it accessible on the network, the Network Camera must be assigned an IP address.

Note:

•

A network DHCP server is optional.

•

The Network Camera has the default IP address 192.168.0.123.

•

If IP assignment fails, check that there is no firewall blocking its operation and check that the Network

Camera and your computer's IP is located on the same subnet.

Assign an IP address using IP Installer

IP installer automatically search and display KT&C network devices on your network. The application can also be used to manually assign a static IP address.

Note:

The computer running the IP installer must be on the same network segment (physical subnet) as the Network Camera.

Accessing the Network Camera

1. Start your browser(when you rst run ActiveX to install, run an “IE as Administrator” on Window 7 or Vista).

2. Enter the IP address or host name of the Network Camera in the Address eld of your browser.

3. If you are accessing the Network Camera for the rst time, you will see the following warning

message as shown below.

6. Terminal Block Connectors

KNC-VDi100HD, KNC-VNi100HD, KNC-VDi120HD, KNC-VNi120HD are connected with external equipment as following diagram below.

Circuit diagram

1. Check that the Network Camera is connected to the network and that power has been applied.

2. Start KT&C IP installer.

4. Click the warning message and select “Install ActiveX Control…”.

5. Click “Install” to install the KT&C Web Viewer.

6. If a Windows Security Alert pop-up appears, click “Unblock”.

KNC-VDi100HD

1. INPUT – Connect the external sensor e.g. PIR motion sensor. (3.3V DC pull-up built in) A. ON - Short-circuit with GND. B. OFF - Open

CAUTION :

2. OUT – Connect the external alarm e.g. light or buzzer.

CAUTION :

with the load, for protection against voltage transients.

CAUTION

Digital Input must not be exposed to voltages greater than 10V DC.

If used with an external relay, a diode must be connected in parallel

: Max. load = 70mA Max voltage = 12V DC.

Example of terminal connection

3. When the Network Camera is displayed as shown above, select the unit that need to be assigned an IP.

A. Refresh Device List – Rescan local network to nd the Network Camera.

B. Authenticate – Enter the administrator ID and password.

* Default User ID and Password is [ID: admin, Password: admin]

C. Host Name – Enter the Host Name of the Network Camera. D. IP Settings

i. Dynamic – Assign dynamic IP address automatically from DHCP server on your network. ii. Static – Assign static IP address manually. iii. Port – Enter the HTTP port the Network Camera will use. The default setting is 80.

Alternatively, any port in the range 1024-65535 may be used, but check rst with your

system administrator before changing the default setting.

E. Network Settings

i. Subnet Mask – Specify the mask for the subnet the Network Camera located on. ii. Gateway – Specify the IP address of the default router (gateway) used for connecting devices attached to different networks and network segments. iii. Pri. DNS – Enter the IP address of the primary DNS server. This server provides the translation of host names to IP addresses on your network. iv. Sec. DNS – Specify the IP address of the secondary DNS server. This will be used if the primary DNS server is unavailable.

4. Click the “Set” button to save conguration.

7. After installing the KT&C Web View ActiveX Control, a Login page will be displayed. Enter the user ID and password.

Note:

Default User ID and Password is [ID: admin, Password: admin]

8. The video image displays in your browser.

TERMINAL CONNECTION

Note:

To view streaming video in Microsoft Internet Explorer, you must set your browser to allow the “KT&C Web Viewer” to be installed on your computer. This ActiveX component is installed the first time a video stream is accessed.

KT&C KNC-VNi120HD User Manual

Specifications and Main Features

Frequently Asked Questions

User Manual