KT&C DR28V12IR Operation Manual

ULTRA HIGH RESOLUTION

VANDAL DOME CAMERA

OPERATION MANUAL

M222-DR28V12-001

Thank you for choosing our high quality camera.
Before attempting to connect or operate, please read and follow these instructions.

CONTENTS

1. NOTICES

2. FOR YOUR SAFETY

3. FEATURES

4. EQUIPMENT AND ACCESSORIES

5. OVERVIEW AND FUNCTION

6. INSTALLATION

7. CONNECTION

8. DIMENSIONS

9. SPECIFICATION

10. OSD MENU STRUCTURE

2

These servicing instructions are for use by qualied service personnel only.
To reduce the risk of electric shock do not perform any servicing other than
that contained in the operating instructions unless you are qualied to do so.

Use Class 2 Power Supply Only

CAUTION

3

1. NOTICES

This device complies with Part 15 of FCC regulations.
Operation is subject to the following two conditions:

1. This device may cause harmful interference.

2. This device may receive interference that can cause affect the operation of this
equipment.

Note

This equipment has been tested and found to comply with the limits for a
Class A digital device, pursuant to Part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference when the
equipment is operated in a commercial environment. This equipment generates,
uses, and can radiate radio frequency energy and, if not installed and used
in accordance with the instruction manual, may cause harmful interference to
radio communications. Operation of this equipment in a residential area is likely
to cause harmful interference in which case the user will be required to correct
the interference problems at his or her own expense.

Caution

Alteration or modifications carried out without. appropriate authorization may
invalidate the user's right to operate the equipment.

1. A regulated DC12V 500mA power supply is recommended to ensure the best picture
quality and stable operation.
An unregulated power supply may cause damage to the camera.

Using an unregulated power supply will void the product warranty.

2. It is recommended that the camera is used with a monitor that has a CCTV quality
75 video impedance level.
If your monitor is switched to high impedance, then please adjust accordingly.

3. Do not attempt to disassemble the camera to access internal components.
Refer servicing to your dealer.

4. Never face the camera towards the sun or any bright or reective light, which may

cause smear on the picture and possible damage to the CCD.

5. Do not remove the serial sticker for the warranty service.

1. CAUTIONS

4

WEEE

(Waste Electrical & Electronic Equipment)

This marking shown on the product or its remove, indicates that it should not
be disposed with other household wastes at the end of its working life. To
prevent possible harm to the environment or human health from uncontrolled
waste disposal, please separate this from other types of wastes and recycle it
responsibly to promote the sustainable reuse of material resources. Household
users should contact either the retailer where they purchased this product, or

their local government ofce, for details of where and how to safely recycle the

item.
Business users should contact their supplier and check the terms and
conditions of the purchase contract.
This product should not be mixed with other commercial wastes for disposal.

CAUTION

RISK OF ELECTRIC SHOCK.

DO NOT OPEN

CAUTION:

TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT
REMOVE COVER (OR BACK). NO USER SERVICEABLE
PARTS INSIDE. REFER SERVICING TO QUALIFIED
SERVICE PERSONNEL.

This symbol is intended to alert the user to the presence
of uninsulated “dangerous voltage” within the product’s

enclosure that may be of sufcient magnitude to constitute a

risk of electric shock.

This symbol is intended to alert the user to the presence of
important operating and maintenance (servicing) instructions
in the literature accompanying the appliance.

2. FOR YOUR SAFETY

1) All warning and instruductions in this manual should be followed.

2) Save this manual for future reference.

3) Heed all warnings.

4) Follow all instructions.

5) Do not use this apparatus near water.

6) Clean only with a dry cloth.

7) Do not block any ventilation openings. Install in accordance

with the manufacturer’s instructions.

8) Do not install near any heat sources such as radiators, heat registers,
stoves, or other apparatus (including ampliers) that produce heat.

9) To help prevent from electric shock, plug the equipment and peripheral power cables

into properly polarized or grounded electrical outlets. These cables are equipped with
the wide blade or the third prong to ensure proper grounding. Do not use adapter

plug or remove the ground prong from a cable. If the provided plug does not t your

outlet, consult an electrician.

10) Ensure that nothing rests on your equipment's cabloe and that the cables are not

located where they can be stpped on, trapped over, or pinched.

11) Only use attachments or accessories as specied.

12) Only use the equipment with the cart, stand, tripod, bracket, or table that is specied

by the manufacturer or sold with the apparatus. When a cart is used, use caution to
prevent the cart from tipping over and to avoid injury.

13) Do not connect or disconnect during lighting storms due to risk of electric shock.

14) If any of the following conditions occur, unplug the equipment from the electrical

outlet and replace the part or contact your trained service provider:

• The power cable, extension cable, or plug is damaged.

• An object has fallen into the equipment.

• The equipment has been exposed to water.

• The equipment has been dropped or damaged.

• The equipment does not operate correctly when you follow the operating

instructions.

5

3. FEATURES

• Superlative resolution of over 750 horizontal TV lines for amazing image quality.

• 960H CCD for sensor sensitivity of .001 lux in low light without DSS boost.

960H CCD sensor with high IR sensitivity. (LED Type)

• True Day/Night zero light operating range of 100 feet or more (LED Type)

(depending on scene reflectivity) from 24 IR LEDs with Smart automatic
exposure level adjust to achieve the desired IR brightness in a user defined area.

• Full motion color or digital day/night during low ambient light without ghosting.

• Simple and easy to use OSD setup menu.

- Digital Wide Dynamic Range(DWDR) to properly expose images during unbalanced
light contrast in the scene.

- Anti Color Roll white balance option resists fluorescent light interference.

- Optional Back Light Compensation (BLC) and Highlight Compensation (HLC).

- Adjustable 2D-Noise Reduction to increase picture clarity and improve
utilization of DVR disk storage.

- Privacy image masking for 4 configurable zones.

• Varifocal DC iris lens to capture the desired field of view.

• Dual voltage (12VDC/24VAC) with Anti Color Roll.

• Service Video output for convenient installation, and ease of service.

• 3-Axis gimbal for convenient wall or ceiling mounting.

• Optional junction box plate.

6

7

4. EQUIPMENT AND ACCESSORIES

Camera Manual

Template

Screws(3ea) / Plastic Anchors (3ea)
/ Wrench / Micro Screw (1ea)

Service Video Output Test Cable

Pigtail Cable (12VDC only) Pigtail Jack (Dual)

OPTIONAL ACCESSORIES

-Wall mount bracket :

wall mount bracket with ½” conduit ttings

top and bottom.

8

Box adapter

- Ju n ct ion b ox mo un t a da pte r for
outdoor dome camera

- Rough-in box adapter ts 1 or 2 gang
or 4" octagonal/square/round boxes

5. OVERVIEW AND FUNCTION

9

• LED Type

• Standard Type

IR LED

OSD Joystick

OSD Joystick

Service Video
Connector

Service Video
Connector

6. INSTALLATION

• LED Type

10

Template

Housing Bottom

Dome Cover

Cover Screws

Shroud

Screws

3-AXIS Gimbal

Plastic Anchors

Lens Zoom Knob

Lens Focus Knob

6. INSTALLATION

• Standard Type

11

Lens Zoom Knob

Lens Focus Knob

Housing Bottom

Dome Cover

Cover Screw

Shroud

Screw

3-AXIS Gimbal

Plastic Anchors

Template

7. CONNECTION

- DC12V

- DC12V/AC24V

- Service Video Connector

When you install the camera, please glue up the end of cable to
keep it stable and to protect the camera.

12

OPEN

COVER

Service Video Connector

BNC FEMALE
VIDEO

VIDEO IN

DC 12V
POWER SUPPLY

VIDEO IN

HANDHELD MONITOR

TEST CABLE

DC 12V / AC 24V

DUAL POWER SUPPLY

PIGTAIL JACK

VIDEO IN

DC12V
(DC Jack)

MONITOR

MONITOR

BNC FEMALE
VIDEO

8. DIMENSIONS

Unit : mm(inch)

13

Ø133 (5.24")

Ø120 (4.72")

3-120

˚

Ø80 (3.15")

67.8 (2.67")

111.8 (4.4")

9. SPECIFICATION

Standard type LED type

Imaging Device 1/3" 960H High Sensitivity CCD

Video Format NTSC / PAL

Picture Elements NTSC: 1020(H)x508(V) / PAL: 1020(H) X 596(V)
Effective Picture Elements NTSC: 976(H) x 494(V) / PAL: 976(H) X 582(V)
Horizontal Resolution More than 750 TVL

Sensitivity

0.001 lux native from sensor,
with Lens 0.2 lux

0 lux OR on;

0.001 lux native from sensor

IR LEDs - 24 LEDs with output at 850nm

IR Range* -

100' (*As with all IR cameras, IR range will vary

based on scene IR reectivity and illumination)

Smart IR Exposure Adjust -

Off/On; adjustable for gain, size and location of

sensing area
S/N Ratio Over 50dB (AGC off)
Video Output BNC 1.0V p-p 75Ω; video test point inside dome, cable supplied
Gamma Correction 0.45
Lens Type 2 Megapixel Aspheric Varifocal DC Iris 2.8-12mm F=1.6
Lens Positioning 3-axis exible positioning for wall or ceiling mounting

Back/High Light Compensation OFF / BLC / HLC Selectable

Auto Gain Control Off / Low / Middle / High
Electronic Shutter Auto; or 1/60, FLK, 1/250, 1/500, 1/1000, 1/2000, 1/4000, 1/5000, 1/10000, 1/100000
White Balance ATW / AWB / AWC -> SET / Anti-Color Roll / Manual
Sync. Mode Internal (plus Anti-Chroma Crawl White Balance option above)

Day & Night

Electronic D/N control;
Choose Auto or B/W

Auto True D/N with motorized ICR;

Controlled by photo sensor
OSD Menu Multiple functions using 3-axis joystick
OSD Languages English, Spanish, Portuguese, German, Russian, Japanese, Chinese, French
2D-DNR On / Off (Level Adjustable)

Digital Wide Dynamic Range On / Off (Level Adjustable)

Mirror Off / On

Motion Detection Off / On for 4 selectable zones (On screen indication)

Privacy Mask Off / On for 8 selectable zones
Lens Shading Correction Off / On with adjustable level and center

Other OSD Functions

Camera Title with position, Font Color, Image Contrast / Sharpness,
CRT / LCD display optimization, Negative Image, DPC (Dead Pixel Compensation)

Power Source 12VDC, DUAL (12VDC / 24VAC)

Power
Consumption

DC 12VDC (±10%), 140mA max. 12VDC (±10%), 250mA max.

DUAL

12VDC (±10%), 170mA max.
24VAC (±10%), 2.2W max.

12VDC (±10%), 320mA max.

24VAC (±10%), 3.8W max.

Operating Temperature -40°C ~ 60°C (-40°F ~ 140°F)
Storage Temperature -20°C ~ 60°C (-4°F ~ 140°F)
Environmental IP68 waterproof

Mechanical

Three axis, twist-open plastic dome;

choice of black body (B sufx) and white body (W sufx)

Dimensions Bubble Ø80(3.15"), Ø133(5.24") x 111.8(4.4")

Weight 25.40 oz./ 1.59 lb. / 720g 25.93 oz./ 1.62 lb. / 735g

Mounting Options

Junction Box Plate

Certications CE / FCC / RoHS

Specications and designs are subject to change for improving the functionality of this product without notice.

10. OSD MENU STRUCTURE

• Menu structure

Main 1st Sub Menu 2nd Sub Menu 3rd Sub Menu

LENS

DC

BRIGHTNESS 0 ~ 255
IRIS SPEED 0 ~ 15
RETURN SAVE&END

MANUAL BRIGHTNESS 0 ~ 255

RETURN SAVE&END

EXPOSURE

SHUTTER

AUTO

1/60(NTSC),1/100(NTSC),FLK,
1/250,1/500,1/1000,1/2000,1/4000
1/5000,1/10000,1/100000

AGC OFF / LOW / MID / HIGH * LED Type is adjustable.
DWDR OFF/ON 0 ~ 63

RETURN SAVE&END

RETURN SAVE&END

WHITE
BALANCE

ATW
AWB

AWC -> SET

ANTI. CRL

MENUAL

COLOR TEMP

MENUAL
INDOOR

OUTDOOR
BLUE 0 ~ 255
RED 0 ~ 255

RETURN SAVE&END

BACKLIGHT

OFF

BLC

AREA SEL.

AREA 1

AREA 2
AREA STATE OFF/ON
GAIN 0 ~ 255
HEIGHT 0 ~ 15
WIDTH 0 ~ 15

LEFT/RIGHT 0 ~ 15
TOP/BOTTOM 0 ~ 15

RETURN SAVE&END

HLC

OFF

HLC

LEVEL 0 ~ 255

MODE

NIGHT ONLY
ALL DAY

MASK SKIP

OFF / ON

HEIGHT 0 ~ 15
WIDTH 0 ~ 15

LEFT / RIGHT 0 ~ 15
TOP / BOTTOM 0 ~ 15

RETURN SAVE&END

RETURN SAVE&END

15

10. OSD MENU STRUCTURE

Main 1st Sub Menu 2nd Sub Menu 3rd Sub Menu

DAY&NIGHT

* Standard

Type is

adjustable.

COLOR

BW

BURST OFF/ON

IR SMART

OFF/ON

IR GAIN 0 ~ 255
HEIGHT 0 ~ 15
WIDTH 0 ~ 15

LEFT/RIGHT 0 ~ 15
TOP/BOTTOM 0 ~ 15

RETURN SAVE&END
IR LEVEL LOW/MID/HIGH * Disabled
RETURN SAVE&END

D&N EXT

D->N DELAY 1, 3, 5, 10, 15, 20, 25, 30
N->D DELAY 1, 3, 5, 10, 15, 20, 25, 30

RETURN SAVE&END

*IR SMART Feature:

IR SMART feature only works at B/W mode.

IR Smart feature adjusts AE LEVEL to prevent a subject being too bright by the saturation of light.

1.LED Type

After enabling the “IR SMART” function under B/W mode, make sure to switch the DAY&NIGHT mode to “EXT” before

saving the setting.

Leaving the mode under B/W when saving will result in constant B/W mode output.

2.STANDARD Type

After changing the “IR SMART” function under B/W mode, make sure to switch the AUTO mode to “SAVE” before

saving the setting.

Leaving the mode under B/W when saving will result in constant B/W mode output.

SPECIAL

CAM TITLE

OFF/ON

0 1 2 3 4 5 6
7 8 9 A B C D E
F G H I J K L M
N O P Q R S T U
V W X Y Z

→ ←
↑ ↓ ( ) - _ ■
/ = : " . , ┛

← →

CLR POS END

MOTION

OFF/ON

AREA SEL.

AREA1
AREA2
AREA3

AREA4
AREA STATE OFF/ON
HEIGHT 0 ~ 15
WIDTH 0 ~ 15

LEFT/RIGHT 0 ~ 15
TOP/BOTTOM 0 ~ 15

DEGREE 0 ~ 255
VIEW OFF/ON
RETURN SAVE&END

16

10. OSD MENU STRUCTURE

Main 1st Sub Menu 2nd Sub Menu 3rd Sub Menu

SPECIAL

PRIVACY

OFF / ON

AREA SEL.

AREA1 / AREA2 / AREA3 / AREA4

AREA5 / AREA6 / AREA7 / AREA8

AREA STATE OFF / ON
HEIGHT 0 ~ 15
WIDTH 0 ~ 15

LEFT / RIGHT 0 ~ 15
TOP / BOTTOM 0 ~ 15

COLOR 0 ~ 15
RETURN SAVE&END

IMAGE ADJ

LENS SHAD.

OFF / ON

LEVEL 0 ~ 255

H-CENTER 0 ~ 255

V-CENTER 0 ~ 255

RETURN SAVE&END

2DNR

OFF / ON

LEVEL 0 ~ 15

RETURN SAVE&END
MIRROR OFF / ON

FONT COLOR

FONT 0 ~ 15

ID&TITLE 0 ~ 15

RETURN SAVE&END
CONTRAST 0 ~ 255
SHARPNESS 0 ~ 31

DISPLAY

CRT

PED LEVEL (0 ~ 63)
COLOR GAIN (0 ~ 255)
RETURN (SAVE&END)

LCD

GMMA (0.3 ~ 1.0)
PED LEVEL (0 ~ 63)
COLOR GAIN (0 ~ 255)
RETURN (SAVE&END)

RETURN SAVE&END
NEG. IMAGE OFF / ON
RETURN SAVE&END

LANGUAGE

ENGLISH / CHINESE / SPANISH / RUSSIAN / GERMAN / PORTUGUESE
FRENCH / JAPANESE

DPC

START
DPC VIEW OFF / ON
LS VALUE (0 ~ 63)
DIFF (0 ~ 63)
AREA HS (0 ~ 255)
AREA HE (0 ~ 255)
AREA VS (0 ~ 255)
AREA VE (0 ~ 255)

RETURN SAVE&END

RETURN

SAVE / NOT SAVE / RESET

*Important Note:

- Any changes made to the camera settings must be saved prior to exiting the OSD menu.
Else all changes will be discarded.

17