KT&C ACE-M321NU User Manual

M112-M321-002

Ultra-High Resolution

COLOR MODULE CAMERA

Thank you for choosing our high quality camera.
Before attempting to connect operate this unit, please
read and follow these instructions.

OPERATION MANUAL

CAUTIONS

This device complies with Part 15 of the FCC Rules.
Operation is subject to the following two conditions;

1. This device may not cause harmful interference.

2. This device must accept any interference received, including
interference that may cause undesired operation.

Note -

This equipment has been tested and found to comply with the
limits for a Class A digital device, pursuant to part 15 of the FCC
Rules. These limits are designed to provide reasonable protection
against harmful interference when the equipment is operated in
a commercial environment. This equipment generates, uses, and
can radiate radio frequency energy and, if not installed and used
in accordance with the instruction manual, may cause harmful
interference to radio communications. Operation of this equipment
in a residential area is likely to cause harmful interference in which
case the user will be required to correct the interference at his own
expense.”

WARNING -

This is a class A product. In a domestic environment this product
may cause radio interference in which case the user may be
required to take adequate measures.

Caution -

Any changes or modications in construction of this devies which

are not expressly approved by the party responsible for compliance
could void the user's authority to operate the equipment.

1. A regulated DC12V 300mA power supply is recommended for use with
this camera for the best picture and the most stable operation.

An unregulated power supply can cause damage to the camera.
When unregulated power supply is applied, product warranty will be
out of subject.

2. It is recommended that the camera is used with a monitor that has a
CCTV quality 75 video impedance level. If your monitor is switched to high
impedance then please adjust accordingly.

3. Do not attempt to disassemble the camera to gain access to the internal
componets. Refer servicing to your dealer.

4. Never face the camera towards the sun or any bright or reective light,

which may cause smear on the picture and possible damage to the CCD.

5. Do not remove the serial sticker for the warranty service.

CAUTION

CAUTIONS

Correct Disposal of This Product

(Waste Electrical & Electronic Equipment)

(Applicable in the European Union and other European
countries with separate collection systems)

This marking shown on the product or its literature, indicate that
it should not be disposed with other household wastes at the end
of its working life. To prevent possible harm to the environment or
human health from uncontrolled waste disposal, please separate
this from other types of wastes and recycle it responsibly to promote
the sustainable reuse of material resources.

This product should not be mixed with other commercial wastes

purchased this product, or their local government ofce, for details

of where and how they can take item for environmentally safe
recycling.

Business users should contact their supplier and check the terms
and conditions of the purchase contract.
Household users should contact either the retailer where they for
disposal.

RISK OF ELECTRIC SHOCK DO NOT OPEN

CAUTION : TO REDUCE THE RISK OF ELECTRIC SHOCK, DO

NOT REMOVE COVER(OR BACK). NO USER.
SERVICING TO QUALIFED SERVICE PERSONNEL.

This symbol is intended to alert the user to the presence
of uninsulated "dangerous voltage" within the product's

enclosure that may be of sufcient mangnitude to constitute

a risk of electric shock to persons.

This symbol is intended to alert the user to the presence of
important operating and maintenance(servicing) instruction in
the literature accompanying the appliance.

CAUTION

FEATURES

• 1/3” SONY EXview HAD CCD II

• High Resolution of 700TV Lines

• OSD (5-Port KEY)

• Multi Language

(ENGLISH / JAPANESE / GERMAN / FRENCH /
RUSSIAN / PORTUGUESE / SPANISH / CHINESE)

• 2DNR

• Privacy Zone 4Zones

• Motion Detection 4Zones

• DC IRIS Control (Option)

• Only DC12V

• ATR

(Adaptive Tone-curve Reproduction / Digital WDR)

The function provides gradation compensation to improve
the contrast of subjects both low-luminance areas and high
luminance areas exist in the same picture

• IR Optimizer

If,when the night operation mode of the DAY/NIGHT function
is established, the mode is used together with an external
infrared LED light source, excessive front lighting may occur,
resulting in overexposure.
The IR Optimizer function makes it possible to minimize this
overexposure by optimizing the exposure
control during Night operations.

SPECIFICATION

Signal Format NTSC PAL
Image Device 1/3” 960H SONY EXview HAD CCD II
Scanning

System
H.Resolution 750TV Lines
Scanning

Frequency
Total Pixels

1020(H) X 508(V) 1020(H) X 596(V)

Effective Pixels 976(H) X 494(V) 976(H) X 582(V)
Electronic

Shutter Speed

1/60~1/100,000sec 1/50~1/100,000sec

S/N Ratio More than 50dB(AGC OFF)
Gamma r =0.45
Min.

Illumination
Sync System Internal

Video Output 1.0 Vp-p Composite 75(Ω) unbalanced
OSD Built in

BLC OFF / BLC / HLC
White

Balance

ATW / PUSH / USER1 / USER2 / ANTI CR /

2DNR OFF / ON(Level adjustable)

2 : 1 Interlace

15.734KHz(H),

59.94Hz(V)

0.1Lux / F2.0

MANUAL / PUSH-LOCK

15.625KHz(H),
50Hz(V)

ATR OFF / ON(Level adjustable)
IR Optimizer OFF / ON(Level adjustable)

Function
Privacy

Masking
Motion

Detection

MIRROR / BRIGHTNESS / CONTRAST /

SHARPNESS/HUE / GAIN

4 Zones

4 Zones
Day & Night AUTO / COLOR / BW / EXT1 / EXT2
Lens

Language

Input Power
Source

Operating
Temperature

Storage
Temperature

Operating
Humidity

Vari-focal, Board,

Pinhole, C/CS Mount (DC-IRIS only)
ENGLISH / JAPANESE / GERMAN /

FRENCH / RUSSIAN /

PORTUGUESE / SPANISH / CHINESE

DC 12V ±10% Max 100mA

14°F~122°F (-10°C~+50°C)

-4°F~140°F (-20°C~+60°C)

Less than 80%

Dimension 32mmX32mm

Specications and designs are subject to change for improving

the functionality of this product without notice.

CONNECTION

J104

1 4

J102

1) J102(DN_EXT)

PIN NO. NAME I/O

1 +12V O
2 GND ­3 Day&Night SIGNAL I

2) J103(MAIN)

PIN NO. NAME I/O

1 Not used ­2 K_DOWN I
3 K_UP I
4 K_ENTER I
5 K_RIGHT I
6 K_LEFT I
7 GND ­8 VIDEO O
9 GND -

10 +12V I

1 103 1

J103

3) J104(DC IRIS)

PIN NO. NAME I/O

1 DAMP + O
2 DAMP - O
3 DRV + O
4 GND -

DIMENSIONS

Unit(mm)

- BOARD LENS -

32

28

< TOP VIEW >

17.21.2

- PIN HOLE LENS -

28

- VARIFOCAL LENS -

32

9.716.2 1.21.2

OSD MENU STRUCTURE

MAIN MENU 1st Sub MENU 2nd Sub MENU 3rd Sub MENU 4th Sub MENU

LENS

SHUTTER/AGC

WHITE BAL

BACK LIGHT OFF,BLC,HLC

PIC ADJUST

ATR

MOTION DET

NEXT
EXIT
SAVE ALL

*SHUT+IRIS:
*Auto Iirs(Default):

The Shutter stays at the manually selected value and only the Mechanical Iris adjusts brightness.

MANUAL

AUTO

AUTO

MANUAL

ATW

PUSH

USER1

USER2

ANTI CR

MANUAL

PUSH LOCK

MIRROR OFF,ON
BRIGHTNESS (000 ~ 255)
CONTRAST (000 ~ 255)
SHARPNESS (000 ~ 255)
HUE (000 ~ 255)
GAIN (000 ~ 255)
RETURN

ON

OFF

ON

OFF

Both the Shutter and the Mechanical Iris are automatically adjusted according to brightness.

TYPE DC
MODE AUTO,OPEN,CLOSE
SPEED (000 ~ 255)
RETURN

HIGH
LUMINANCE

LOW
LUMINANCE

RETURN
MODE SHUT+AGC

SHUTTER

AGC 6,12,18,24,30,36,42,44.8
RETURN
SPEED (000 ~ 255)
DELAY CNT (000 ~ 255)
ATW FRAME x0.50,x1.00,x1.50,x2.00
ENVIRONMENT INDOOR,OUTDOOR
RETURN

B-GAIN (000 ~ 255)
R-GAIN (000 ~ 255)
RETURN
B-GAIN (000 ~ 255)
R-GAIN (000 ~ 255)
RETURN

LEVEL
RETURN

LUMINANCE LOW,MID,HIGH
CONTRAST
RETURN

DETECT SENS (000 ~ 127)
BLOCK DISP
MONITOR AREA ON,OFF

AREA SEL

RETURN

MODE
BRIGHTNESS (000 ~ 255)

MODE AGC,OFF
BRIGHTNESS x0.25,x0.50,x0.75,x1.00

1/50(PAL),1/100(NTSC)
1/60(NTSC),1/120(PAL)
1/250,1/500,1/1000
1/2000,1/4000,1/10000

NTSC:(30 ~ 115)
PAL:(28 ~ 134)

LOW,MIDLOW,MID,
MIDHIGH,HIGH

OFF,ON,ENABLE
(CONTROLER)

1/4, 2/4, 3/4, 4/4
TOP

BOTTOM

LEFT

RIGHT

SHUT,AUTO IRIS,
SHUT+AUTO IRIS

NTSC:(000 ~ 244)
PAL:(000 ~ 288)

NTSC:(000 ~ 244)
PAL:(000 ~ 288)

NTSC:(000 ~ 474)
PAL:(000 ~ 468)

NTSC:(000 ~ 474)
PAL:(000 ~ 468)

MAIN MENU 1st Sub MENU 2nd Sub MENU 3rd Sub MENU 4th Sub MENU

AREA SEL

PRIVACY

DAY/NIGHT

NR

CAMERA ID

LANGUAGE ENGLISH /
CAMERA
RESET
BACK
EXIT
SAVE ALL

*Important Note :

- Any changes made to the camera settings must be saved prior to exiting the OSD menu.
Else all changes will be discarded.

- By changing the lens option in the OSD from MANUAL to AUTO will automatically change the
SHUTTER/AGC setting from AUTO IRIS to SHUT+AUTO IRIS.(Default:AUTO IRIS)

ON

COLOR (1 ~ 8)
TRANSP 0.00, 0.50, 0.75, 1.00
MOSAIC OFF,ON

OFF

AUTO

COLOR

BW

EXT1
EXT2
NR MODE OFF,Y,C,Y/C
Y LEVEL (000 ~ 015)
C LEVEL (000 ~ 015)
RETURN

ON

OFF

RETURN

BURST OFF,ON
DELAY CNT 0 ~ 255
DAY -> NIGHT 0 ~ 255
NIGHT -> DAY 0 ~ 255
RETURN

BURST OFF,ON
IR OPTMIZER OFF,ON
MODE AUTO, CENTER
LEVEL 0 ~ 31
RETURN

EDIT MODE
RETURN

日本語

/ DEUTSCH / FRANCAIS /

1/4, 2/4, 3/4, 4/4
TOP

BOTTOM

LEFT

RIGHT

Русский

NTSC:(000 ~ 244)
PAL:(000 ~ 288)

NTSC:(000 ~ 244)
PAL:(000 ~ 288)

NTSC:(000 ~ 474)
PAL:(000 ~ 468)

NTSC:(000 ~ 474)
PAL:(000 ~ 468)

/ PORTUGUÊS / ESPAÑOL /

中文