KT&C ACE-EDR380NU User Manual

M092-EDR380-001

HIGH RESOLUTION

WDR COLOR MODULE CAMERA

OPERATION MANUAL

Thank you for choosing our high quality camera.
Before attempting to connect or operate, please read and
follow these instructions.

CAUTIONS

This device complies with Part 15 of the FCC Rules.
Operation is subject to the following two conditions;

1. This device may not cause harmful interference.

2. This device must accept any interference received, including
interference that may cause undesired operation.

Note -

This equipment has been tested and found to comply with the
limits for a Class A digital device, pursuant to part 15 of the FCC
Rules. These limits are designed to provide reasonable protection
against harmful interference when the equipment is operated in
a commercial environment. This equipment generates, uses, and
can radiate radio frequency energy and, if not installed and used
in accordance with the instruction manual, may cause harmful
interference to radio communications. Operation of this equipment
in a residential area is likely to cause harmful interference in which
case the user will be required to correct the interference at his own
expense.”

WARNING -

This is a class A product. In a domestic environment this product
may cause radio interference in which case the user may be
required to take adequate measures.

Caution -

Any changes or modications in construction of this devies which

are not expressly approved by the party responsible for compliance
could void the user's authority to operate the equipment.

1. A regulated DC12V 300mA power supply is recommended for use with
this camera for the best picture and the most stable operation.

An unregulated power supply can cause damage to the camera.
When unregulated power supply is applied, product warranty will be
out of subject.

2. It is recommended that the camera is used with a monitor that has a
CCTV quality 75 video impedance level. If your monitor is switched to high
impedance then please adjust accordingly.

3. Do not attempt to disassemble the camera to gain access to the internal
componets. Refer servicing to your dealer.

4. Never face the camera towards the sun or any bright or reective light,

which may cause smear on the picture and possible damage to the CCD.

5. Do not remove the serial sticker for the warranty service.

CAUTION

CAUTIONS

Correct Disposal of This Product

(Waste Electrical & Electronic Equipment)

(Applicable in the European Union and other European
countries with separate collection systems)

This marking shown on the product or its literature, indicate that
it should not be disposed with other household wastes at the end
of its working life. To prevent possible harm to the environment or
human health from uncontrolled waste disposal, please separate
this from other types of wastes and recycle it responsibly to promote
the sustainable reuse of material resources.

This product should not be mixed with other commercial wastes

purchased this product, or their local government ofce, for details

of where and how they can take item for environmentally safe
recycling.

Business users should contact their supplier and check the terms
and conditions of the purchase contract.
Household users should contact either the retailer where they for
disposal.

RISK OF ELECTRIC SHOCK DO NOT OPEN

CAUTION : TO REDUCE THE RISK OF ELECTRIC SHOCK, DO

NOT REMOVE COVER(OR BACK). NO USER.
SERVICING TO QUALIFED SERVICE PERSONNEL.

This symbol is intended to alert the user to the presence
of uninsulated "dangerous voltage" within the product's

enclosure that may be of sufcient mangnitude to constitute

a risk of electric shock to persons.

This symbol is intended to alert the user to the presence of
important operating and maintenance(servicing) instruction in
the literature accompanying the appliance.

CAUTION

FEATURES

• 1/3 960H SONY Double Scan Super HAD CCD II

• High Resolution of 700TV Lines

• WDR (Wide Dynamic Range)

• OSD Function

• Multi Language
(English / Chinese / Russian / Spanish / German)

• Digital slow shutter

• 3DNR

• Privacy Zone 15Zone

• 3x Digital Zoom

• Motion Detect, Face Detection

• Only DC12V

• RS-232C TTL Level Interface(RS-485 Option)

• A/D Remote Controller > Option

How WDR makes better image?

WDR allows every detail to be captured accurately even
if one portion is bright while other portions are dark.

Option(Lens.A/D Remocom)

Pin Hole

Lens Type

Function

SW1 : MENU OSD Menu on/off
SW2 : UP OSD Menu up
SW3 : DOWN OSD Menu down
SW4 : LEFT OSD Menu left
SW5 : RIGHT OSD Menu right

Option

Board

Varlfocal

C/CS Mount

CONNECTION DIMENSIONS

SENSOR

1) J103(DC IRIS)

2) J105(IR CUT)

3) J506(DC IRIS)

J103 J105

Top Connector Position

PIN NO. NAME I/O

1 DAMP + O

2 DAMP - O

3 DRV + O

4 GND -

PIN NO. NAME I/O

1 IR CUT OUT + O

2 IR CUT OUT - O

PIN NO. NAME I/O

1 DAMP + O

2 DAMP - O

3 DRV + O

4 GND -

Bottom Connector Position

J508 J507 J506

CONNECTION

4) J507(DN_I/O)

PIN NO. NAME I/O

1 +12V O

2 GND -

3 COLOR/BW IN I

4 COLOR/BW OUT O

5) J508(DN_I/O)

PIN NO. NAME I/O

1 GND -

2 VIDEO O

3 GND -

4 +12V I

5 RXD(TRX-) I/O

6 TXD(TRX+) I/O

7 A/D KEY1 I

8 MOTION O

9 COLOR/BW IN I

10 GND -

COLOR/BW IN Application

Color/BW IN

OPEN: NIGHT MODE
GND: DAY MODE

RS232C TTL LEVEL

HIGH : +3.3V
LOW : GND

Unit(mm)

2-5.0

Control Function

LEFT

Color/BW IN

MENU

13.6

29.8

- BOTTOM VIEW -

UP

DOWN

38

38

- TOP VIEW -

RIGHT

M092-EDR380-001

HIGH RESOLUTION

WDR COLOR MODULE CAMERA

OPERATION MANUAL

Thank you for choosing our high quality camera.
Before attempting to connect or operate, please read and
follow these instructions.

CAUTIONS

This device complies with Part 15 of the FCC Rules.
Operation is subject to the following two conditions;

1. This device may not cause harmful interference.

2. This device must accept any interference received, including
interference that may cause undesired operation.

Note -

This equipment has been tested and found to comply with the
limits for a Class A digital device, pursuant to part 15 of the FCC
Rules. These limits are designed to provide reasonable protection
against harmful interference when the equipment is operated in
a commercial environment. This equipment generates, uses, and
can radiate radio frequency energy and, if not installed and used
in accordance with the instruction manual, may cause harmful
interference to radio communications. Operation of this equipment
in a residential area is likely to cause harmful interference in which
case the user will be required to correct the interference at his own
expense.”

WARNING -

This is a class A product. In a domestic environment this product
may cause radio interference in which case the user may be
required to take adequate measures.

Caution -

Any changes or modications in construction of this devies which

are not expressly approved by the party responsible for compliance
could void the user's authority to operate the equipment.

1. A regulated DC12V 300mA power supply is recommended for use with
this camera for the best picture and the most stable operation.

An unregulated power supply can cause damage to the camera.
When unregulated power supply is applied, product warranty will be
out of subject.

2. It is recommended that the camera is used with a monitor that has a
CCTV quality 75 video impedance level. If your monitor is switched to high
impedance then please adjust accordingly.

3. Do not attempt to disassemble the camera to gain access to the internal
componets. Refer servicing to your dealer.

4. Never face the camera towards the sun or any bright or reective light,

which may cause smear on the picture and possible damage to the CCD.

5. Do not remove the serial sticker for the warranty service.

CAUTION

CAUTIONS

Correct Disposal of This Product

(Waste Electrical & Electronic Equipment)

(Applicable in the European Union and other European
countries with separate collection systems)

This marking shown on the product or its literature, indicate that
it should not be disposed with other household wastes at the end
of its working life. To prevent possible harm to the environment or
human health from uncontrolled waste disposal, please separate
this from other types of wastes and recycle it responsibly to promote
the sustainable reuse of material resources.

This product should not be mixed with other commercial wastes

purchased this product, or their local government ofce, for details

of where and how they can take item for environmentally safe
recycling.

Business users should contact their supplier and check the terms
and conditions of the purchase contract.
Household users should contact either the retailer where they for
disposal.

RISK OF ELECTRIC SHOCK DO NOT OPEN

CAUTION : TO REDUCE THE RISK OF ELECTRIC SHOCK, DO

NOT REMOVE COVER(OR BACK). NO USER.
SERVICING TO QUALIFED SERVICE PERSONNEL.

This symbol is intended to alert the user to the presence
of uninsulated "dangerous voltage" within the product's

enclosure that may be of sufcient mangnitude to constitute

a risk of electric shock to persons.

This symbol is intended to alert the user to the presence of
important operating and maintenance(servicing) instruction in
the literature accompanying the appliance.

CAUTION

FEATURES

• 1/3 960H SONY Double Scan Super HAD CCD II

• High Resolution of 700TV Lines

• WDR (Wide Dynamic Range)

• OSD Function

• Multi Language
(English / Chinese / Russian / Spanish / German)

• Digital slow shutter

• 3DNR

• Privacy Zone 15Zone

• 3x Digital Zoom

• Motion Detect, Face Detection

• Only DC12V

• RS-232C TTL Level Interface(RS-485 Option)

• A/D Remote Controller > Option

How WDR makes better image?

WDR allows every detail to be captured accurately even
if one portion is bright while other portions are dark.

Option(Lens.A/D Remocom)

Pin Hole

Lens Type

Function

SW1 : MENU OSD Menu on/off
SW2 : UP OSD Menu up
SW3 : DOWN OSD Menu down
SW4 : LEFT OSD Menu left
SW5 : RIGHT OSD Menu right

Option

Board

Varlfocal

C/CS Mount

CONNECTION DIMENSIONS

SENSOR

1) J103(DC IRIS)

2) J105(IR CUT)

3) J506(DC IRIS)

J103 J105

Top Connector Position

PIN NO. NAME I/O

1 DAMP + O

2 DAMP - O

3 DRV + O

4 GND -

PIN NO. NAME I/O

1 IR CUT OUT + O

2 IR CUT OUT - O

PIN NO. NAME I/O

1 DAMP + O

2 DAMP - O

3 DRV + O

4 GND -

Bottom Connector Position

J508 J507 J506

CONNECTION

4) J507(DN_I/O)

PIN NO. NAME I/O

1 +12V O

2 GND -

3 COLOR/BW IN I

4 COLOR/BW OUT O

5) J508(DN_I/O)

PIN NO. NAME I/O

1 GND -

2 VIDEO O

3 GND -

4 +12V I

5 RXD(TRX-) I/O

6 TXD(TRX+) I/O

7 A/D KEY1 I

8 MOTION O

9 COLOR/BW IN I

10 GND -

COLOR/BW IN Application

Color/BW IN

OPEN: NIGHT MODE
GND: DAY MODE

RS232C TTL LEVEL

HIGH : +3.3V
LOW : GND

Unit(mm)

2-5.0

Control Function

LEFT

Color/BW IN

MENU

13.6

29.8

- BOTTOM VIEW -

UP

DOWN

38

38

- TOP VIEW -

RIGHT

M092-EDR380-001

HIGH RESOLUTION

WDR COLOR MODULE CAMERA

OPERATION MANUAL

Thank you for choosing our high quality camera.
Before attempting to connect or operate, please read and
follow these instructions.

CAUTIONS

This device complies with Part 15 of the FCC Rules.
Operation is subject to the following two conditions;

1. This device may not cause harmful interference.

2. This device must accept any interference received, including
interference that may cause undesired operation.

Note -

This equipment has been tested and found to comply with the
limits for a Class A digital device, pursuant to part 15 of the FCC
Rules. These limits are designed to provide reasonable protection
against harmful interference when the equipment is operated in
a commercial environment. This equipment generates, uses, and
can radiate radio frequency energy and, if not installed and used
in accordance with the instruction manual, may cause harmful
interference to radio communications. Operation of this equipment
in a residential area is likely to cause harmful interference in which
case the user will be required to correct the interference at his own
expense.”

WARNING -

This is a class A product. In a domestic environment this product
may cause radio interference in which case the user may be
required to take adequate measures.

Caution -

Any changes or modications in construction of this devies which

are not expressly approved by the party responsible for compliance
could void the user's authority to operate the equipment.

1. A regulated DC12V 300mA power supply is recommended for use with
this camera for the best picture and the most stable operation.

An unregulated power supply can cause damage to the camera.
When unregulated power supply is applied, product warranty will be
out of subject.

2. It is recommended that the camera is used with a monitor that has a
CCTV quality 75 video impedance level. If your monitor is switched to high
impedance then please adjust accordingly.

3. Do not attempt to disassemble the camera to gain access to the internal
componets. Refer servicing to your dealer.

4. Never face the camera towards the sun or any bright or reective light,

which may cause smear on the picture and possible damage to the CCD.

5. Do not remove the serial sticker for the warranty service.

CAUTION

CAUTIONS

Correct Disposal of This Product

(Waste Electrical & Electronic Equipment)

(Applicable in the European Union and other European
countries with separate collection systems)

This marking shown on the product or its literature, indicate that
it should not be disposed with other household wastes at the end
of its working life. To prevent possible harm to the environment or
human health from uncontrolled waste disposal, please separate
this from other types of wastes and recycle it responsibly to promote
the sustainable reuse of material resources.

This product should not be mixed with other commercial wastes

purchased this product, or their local government ofce, for details

of where and how they can take item for environmentally safe
recycling.

Business users should contact their supplier and check the terms
and conditions of the purchase contract.
Household users should contact either the retailer where they for
disposal.

RISK OF ELECTRIC SHOCK DO NOT OPEN

CAUTION : TO REDUCE THE RISK OF ELECTRIC SHOCK, DO

NOT REMOVE COVER(OR BACK). NO USER.
SERVICING TO QUALIFED SERVICE PERSONNEL.

This symbol is intended to alert the user to the presence
of uninsulated "dangerous voltage" within the product's

enclosure that may be of sufcient mangnitude to constitute

a risk of electric shock to persons.

This symbol is intended to alert the user to the presence of
important operating and maintenance(servicing) instruction in
the literature accompanying the appliance.

CAUTION

FEATURES

• 1/3 960H SONY Double Scan Super HAD CCD II

• High Resolution of 700TV Lines

• WDR (Wide Dynamic Range)

• OSD Function

• Multi Language
(English / Chinese / Russian / Spanish / German)

• Digital slow shutter

• 3DNR

• Privacy Zone 15Zone

• 3x Digital Zoom

• Motion Detect, Face Detection

• Only DC12V

• RS-232C TTL Level Interface(RS-485 Option)

• A/D Remote Controller > Option

How WDR makes better image?

WDR allows every detail to be captured accurately even
if one portion is bright while other portions are dark.

Option(Lens.A/D Remocom)

Pin Hole

Lens Type

Function

SW1 : MENU OSD Menu on/off
SW2 : UP OSD Menu up
SW3 : DOWN OSD Menu down
SW4 : LEFT OSD Menu left
SW5 : RIGHT OSD Menu right

Option

Board

Varlfocal

C/CS Mount

CONNECTION DIMENSIONS

SENSOR

1) J103(DC IRIS)

2) J105(IR CUT)

3) J506(DC IRIS)

J103 J105

Top Connector Position

PIN NO. NAME I/O

1 DAMP + O

2 DAMP - O

3 DRV + O

4 GND -

PIN NO. NAME I/O

1 IR CUT OUT + O

2 IR CUT OUT - O

PIN NO. NAME I/O

1 DAMP + O

2 DAMP - O

3 DRV + O

4 GND -

Bottom Connector Position

J508 J507 J506

CONNECTION

4) J507(DN_I/O)

PIN NO. NAME I/O

1 +12V O

2 GND -

3 COLOR/BW IN I

4 COLOR/BW OUT O

5) J508(DN_I/O)

PIN NO. NAME I/O

1 GND -

2 VIDEO O

3 GND -

4 +12V I

5 RXD(TRX-) I/O

6 TXD(TRX+) I/O

7 A/D KEY1 I

8 MOTION O

9 COLOR/BW IN I

10 GND -

COLOR/BW IN Application

Color/BW IN

OPEN: NIGHT MODE
GND: DAY MODE

RS232C TTL LEVEL

HIGH : +3.3V
LOW : GND

Unit(mm)

2-5.0

Control Function

LEFT

Color/BW IN

MENU

13.6

29.8

- BOTTOM VIEW -

UP

DOWN

38

38

- TOP VIEW -

RIGHT

SPECIFICATION

Signal Format NTSC PAL

Image Device 1/3” 960H SONY Double Scan Super HAD CCD II

Scanning System 2:1 Interlace

H.Resolution 750TV Lines

Scanning Frequency H:15.734KHz, V:59.94Hz H:15.625KHz, V:50Hz

Total Pixels 1028(H) X 508(V) 1028(H) X 596(V)

Effective Pixels 976(H) X 494(V) 976(H) X 582(V)

Electronic Shutter 1/60 ~1/100,000sec 1/50 ~1/100,000sec

Digital Zoom Ratio 3x

Digital Slow Shutter OFF, 2 ~ 128 Field

Flickerless ON / OFF

WDR ON / OFF (Level adjustable)

BLC ON / OFF (Level adjustment, Area selection)

3DNR ON / OFF (Level adjustable)

Image Function Image reverse(NORMAL/H / V / HV), Freeze

Sharpness Level adjustable

AGC LOW / MID / HIGH

Day & Night COLOR / BW / AUTO / EXT

Motion Detection ON / OFF (Level adjustable, Area adjustment)

Face Detection ON / OFF (Level adjustable, Area adjustment)

Privacy Masking 15 Zones (Area adjustment)

White Balance ATW / PUSH / PUSH LOCK / MANUAL(R Gain, B Gain)

OSD Built in

Language English / Chinese / Russian / Spanish / German

Protocol Pelco"D"

Baud Rate 2400 / 4800 / 9600 / 19200

S/N Ratio More than 50dB(AGC OFF, 3DNR ON)

Gamma r=0.45

Min. Illumination 0.08Lux(Color) / 0.04Lux(BW) (30IRE@F1.2, AGC:HIGH)

Sync System Internal

SPECIFICATION

Video Output 1.0 Vp-p Composite 75(Ω) unbalanced

Lens

Power Consumption DC 12V ±10%, Max 170mA

OperatingTemperature 14°F~122°F(-10°C~+50°C)

Storage Temperature -4°F~140°F(-20°C~+60°C)

Humidity Less than 80%

External Control A/D KEY, RS232C TTL(RS485 option)

Weight Approx. 35g

Dimensions(mm) 38mm x 38mm x 3 Board

PIN HOLE, Board Lens,

DC IRIS(IR Remove) Vari focal lens, C/CS(DC\VIDEO)

OSD MANUAL

MENU DESCRIPTION

• The best clear image can be obtained color camera with

WDR(Wide Dynamic Range).

• The camera switches lenses automatically depending on the
illumination, which promotes the best possible color images
during the day and black / white image at night.

• The camera function can be controlled by OSD menu.

OSD STRUCTURE

▲,▼ :

•

Menu up / down

,▶ :

•

Menu left / right

◀

:

•

MENU

■

OSD MANUAL

OSD FUNCTION DESCRIPTION

1.LENS

: Enable user to select the lens type according to equipped with camera. Set up
using LEFT, RIGHT KEY at each menu.

- LENS TYPE
①ELC : Enable user to set up for BOARD lens.
②DC : Enable user to set up for DC Iris lens.
③VIDEO : Enable user to set up for VIDEO
Iris lens.

- LEVEL
: Enable user to select the level for Brightness
of image(0~15).

- INITIAL
: Enable user to initialize the LENS menu set up.

2. EXPOSURE

: Enable user to set up the function of SHUTTER, FLICKERLESS, AGC, DSS.
Set up using LEFT, RIGHT KEY at each menu.

- SHUTTER

: Enable user to set up the Shutter Speed

-> 1/60(50), 1/100(120), 1/250, 1/500, 1/1K,
1/2K, 1/4K, 1/10K, 1/100K
*() is for PAL TYPE

- FLICKERLESS
: Enable user to set up the FLICKERLESS ON/OFF.

- AGC
: Enable user to make image bright to amplify
the Gain.

-> LOW, MID, HIGH

- DSS(Digital Slow Shutter)
: Enable user to enhance video quality in extreme low-light condition to slow down

the shutter speed and collect over multiple elds based on the shutter limit setting.

-> OFF, 2X, 4X, 8X, 16X, 32X, 64X, 128X

- INITIAL
: Enable user to initialize the Exposure menu set up.

LENS

>LENS TYPE
LEVEL
INITIAL
RETURN

EXPOSURE

>SHUTTER
FLICKERLESS
AGC
DSS
INITIAL
RETURN

OSD MANUAL

3. WHITE BALANCE

: Enable user to represent the accurate white color by controlling the R,G,B level.
Setting up LEFT, RIGHT KEY on each menu.

- WB MODE

①

ATW : Enable user to trace the White Balance

automatically in the range of 2,300K~10,000K.

②

PUSH : Enable user to search for White Balance
automatically. In this mode, color temperature
range is broader than ATW.

③

...

DC

...

08

...

1/60

...

OFF

...

MID

...

10x

PUSH LOCK : Enable user to x the White

Balance according to the color temperature in
the certain environment.

④

MANUAL : Enable user to sets the White Balance
according to the circumstance.

- RED CONT: In the USER setting of WB MODE, enable user to set the RED GAIN.

- BLUE CONT:In the USER setting of WB MODE, enable user to set the BLUE GAIN.

- PUSH AUTO : In the PUSH LOCK setting of WB MODE, enable user to x the

White Balance in camera setting.

- INITIAL : Enable user to reset the WHITE BALANCE menu setting.

4. WDR/BLC

: Use the condition which Image doesn’t gure out with BLC such as place

surrounded windows and lobby. Set the WDR using the LEFT, RIGHT KEY on
the each menu.

- WDR MODE

①

OFF : None WDR

②

ON : WDR Fixed

- WDR LEVEL
: Enable user to set WDR Level(0~15 level).

- BLC(Back Light Compensation)
: Back Light Compensation

- BLC ZONE : Enable user to set the BLC area.
TOP, BOTTOM, CENTER, LEFT, RIGHT

- BLC LEVEL : Enable user to set BLC in selected
area(0~15 level).

- INITIAL : Enable user to initialize the WDR setting.

WHITE BALANCE

>WB MODE

RED CONT
BLUE CONT
PUSH CONT
INITIAL
RETURN

>WDR MODE
WDR LEVEL
BLC
BLC ZONE
BLC LEVEL
INITIAL
RETURN

WDR/BLC

...
...
...
...

...

...

ATW

...

----

...

----

...

----

OFF
08
OFF
CENTER

04

OSD MANUAL

5. DAY&NIGHT

: Conversion of output image COLOR / BW depending on exterior environment
Enable user to set the LEFT, RIGHT KEY in menu.

- D&N MODE
①COLOR : Enable user to x the output image
in color.
②B/W : Enable user to x the output image in B/W.
③AUTO : Enable user to convert to COLOR/BW
automatically
④EXT : Enable user to convert to COLOR/BW
by signal of the exterior input.

-> Low input signal : COLOR

-> High input signal : BW

- DETECT MODE
①AUTO : SENSOR + VIDEO Detection Mode
Enable user to convert to COLOR/BW by exterior sensor with illumination
②SENSOR : SENSOR Only Detection Mode
Enable user to convert to COLOR/BW automatically by exterior sensor
②VIDEO : VIDEO Only Detection Mode Enable user to convert to COLOR/BW
automatically by luminace element on Screen

- DWELL TIME : In D&N MODE AUTO, enable user to set to delay time for
changing COLOR/BW (0~10sec).

- D->N LEVEL : Day(Color) to Night(BW), level(0~19).

- N->D LEVEL : Night(BW) to Day, level(1~20).

- INITIAL : Enable user to initialize the setting in DAY&NIGHT menu.

SENSOR D->N / N-> D LEVEL

LEVEL LUX LEVEL LUX

0 1 Lux 11 12 Lux

1 2 Lux 12 13 Lux

2 3 Lux 13 14 Lux

3 4 Lux 14 15 Lux

4 5 Lux 15 16 Lux

5 6 Lux 16 17 Lux

6 7 Lux 17 18 Lux

7 8 Lux 18 19 Lux

8 9 Lux 19 20 Lux

9 10 Lux 20 21 Lux

10 11 Lux

DAY & NIGHT

>D&N MODE
DETECT MODE
DWELL TIME
D -> N LEVEL
N -> D LEVE
INITIAL
RETURN

...
...

...
...
...

COLOR

----

----

----

----

OSD MANUAL

6. IMAGE

: REVERSE, DNR, SHARPNESS, FREEZE,
D-ZOOM functions set up by pressing LEFT,
RIGHT KEY.

- REVERSE: Enable user to reverse the image.

-> NORMAL, H, V, H/V

- DNR : Reduces noise by using time-based ltering.

- DNR LEVEL : Enable user to set level(0~15 steps).

- SHARPNESS : Enable user to control the image sharpness (0~15steps).

- FREEZE : Enable user to freeze the image.

- D-ZOOM(Digital Zoom)

-> Max. 3x Digital Zoom.

- INITIAL : Enable user to initialize the setting on IMAGE menu.

IMAGE

>REVERSE
DNR ... OFF
DNR LEVEL ... 4
SHARPNESS
FREEZE
D-ZOOM
INITIAL
RETURN

...

...
...

...

NORMAL

10
OFF
1,0x

OSD MANUAL

7. SPECIAL

: Setting up the CAM TITLE, LANGUAGE,
COMM ADJ, PRIVACY,
MOTION DET, DISPLAY Set up using LEFT
and RIGHT key in each manual.

- CAM TITLE :
Enable user to choose any word in screen.
(Maximum 10 letter is available)

①

A letter Choice from the screen using Menu key.

②

Enable user to move to next menu using

LEFT, RIGHT KEY in LOCATION.

③

By using UP, DOWN, LEFT, RIGHT KEY,
enable user to choose any letters in
LOCATION and then get back to previous step.

④

Enable user to nish words choice and position

by using LEFT, RIGHT KEY in RETURN.

- LANGUAGE :
Enable user to set up an OSD language.

-> ENGLISH, CHINESE, RUSSIAN, SPANISH,
GERMAN

- COMM ADJ : Enable user to set up CAMERA ID,
BAUDRATE.

①

CAM ID: Enable user to set up Camera ID(0~255).

②

BAUDRATE: A communication speed to
Communicate with external device.
(2400, 4800, 9600, 19200).

- PRIVACY: Privacy is the function that covers
some part on screen to prevent private life
(Maximum 15 point covered).

①

ZONE: Enable user to set up positions from 0to14.

②

MASK: Enable user to set up screen output of
chosen position.

③

V START: Mask Vertical start position.

④

V END: Mask Vertical end position.

⑤

H START: Mask Horizontal start position.

⑥

H END: Mask Horizontal end position.

⑦

TOP ANGLE: Top angle position.

⑧

BOTTOM ANGLE: Bottom angle position.

⑨

INITIAL: Enable user to initialize setting of
PRIVACY MENU.

SPECIAL

CAM TITLE

>> <<BACK

[TITLE LOCATION]

...
...
...

...
...

...

...

[-]
ENGLISH
[-]

[-]
[-]

[-]

[-]

>CAM TITLE
LANGUAGE
COMM ADJ
PRIVACY
MOTION DETECT
DISPLAY
INITIAL
RETURN

0123456789ABCDEFGHIJKLMN
OPQRSTUVWXYZ!?*#$%()<>{}

SPACE

LOCATION
RETURN

TITLE

[U] [D] [L] [R] [M] +

CAMM ADJ

PRIVACY

...
...

...
...

...

>CAM ID
BAUDRATE
RETURN

>ZONE NO
MASK
V START ... 07
V END ... 12
H START ... 10
H END ... 19
TOP ANGLE ... 00
BOTTOM ANGLE
INITIAL
RETURN

000
9600

0
OFF

00

OSD MANUAL

- MOTION DET : Motion detection and Face
detection function.

①

MOTION MODE : Enable user to set up ON/OFF.

②

LEVEL : Enable user to setup a motion detect

sensitivity (0~15).

③

FACE MODE : Enable user to set up ON/OFF.

④

LEVEL : Enable user to set up a face detect

sensitivity (0~15).

⑤

V START : Mask Vertical start position.

⑥

V END : Mask Vertical end position.

⑦

H START : Mask Horizontal start position.

⑧

H END : Mask Horizontal end position.

⑨

INITIAL : Enable user to initialize setting

of MOTION DETECT.

- DISPLAY : Enable user to set up a screen marking
of CAM ID, CAM TITLE, MOTION,FACE
① CAM ID : Enable user to set up output on
Camera ID screen.
② CAM TITLE : Enable user to set up output in

xed CAM TITLE.

③ MOTION DETECT : Enable user to set up out
put of MOTION on the screen as
MOTION DET ON setting.
③ FACE DETECT : Enable user to set up out
put of FACE on the screen as
FACE DETECT ON setting.
④ INITIAL : Enable user to initialize of DISPLAY menu.

8. FACTORY DEFAULT

: Enable user to reset all of the status as the factory default
Setting up using LEFT, RIGHT KEY.

9. EXIT

: Enable user to EXIT the OSD menu Setting up using LEFT, RIGHT KEY.

MOTION DET

>MOTION MODE
LEVEL
FACE MODE ... ON
LEVEL ... 07
V START ... 01
V END ... 06
H START ... 01
H END ... 10
INITIAL
RETURN

DISPLAY

>CAM ID
CAM TITLE
MOTION DETECT
FACE DETECT
INITIAL
RETURN

...

ON

...

08

...

OFF

...

OFF

...

OFF

...

OFF

SPECIFICATION

Signal Format NTSC PAL

Image Device 1/3” 960H SONY Double Scan Super HAD CCD II

Scanning System 2:1 Interlace

H.Resolution 750TV Lines

Scanning Frequency H:15.734KHz, V:59.94Hz H:15.625KHz, V:50Hz

Total Pixels 1028(H) X 508(V) 1028(H) X 596(V)

Effective Pixels 976(H) X 494(V) 976(H) X 582(V)

Electronic Shutter 1/60 ~1/100,000sec 1/50 ~1/100,000sec

Digital Zoom Ratio 3x

Digital Slow Shutter OFF, 2 ~ 128 Field

Flickerless ON / OFF

WDR ON / OFF (Level adjustable)

BLC ON / OFF (Level adjustment, Area selection)

3DNR ON / OFF (Level adjustable)

Image Function Image reverse(NORMAL/H / V / HV), Freeze

Sharpness Level adjustable

AGC LOW / MID / HIGH

Day & Night COLOR / BW / AUTO / EXT

Motion Detection ON / OFF (Level adjustable, Area adjustment)

Face Detection ON / OFF (Level adjustable, Area adjustment)

Privacy Masking 15 Zones (Area adjustment)

White Balance ATW / PUSH / PUSH LOCK / MANUAL(R Gain, B Gain)

OSD Built in

Language English / Chinese / Russian / Spanish / German

Protocol Pelco"D"

Baud Rate 2400 / 4800 / 9600 / 19200

S/N Ratio More than 50dB(AGC OFF, 3DNR ON)

Gamma r=0.45

Min. Illumination 0.08Lux(Color) / 0.04Lux(BW) (30IRE@F1.2, AGC:HIGH)

Sync System Internal

SPECIFICATION

Video Output 1.0 Vp-p Composite 75(Ω) unbalanced

Lens

Power Consumption DC 12V ±10%, Max 170mA

OperatingTemperature 14°F~122°F(-10°C~+50°C)

Storage Temperature -4°F~140°F(-20°C~+60°C)

Humidity Less than 80%

External Control A/D KEY, RS232C TTL(RS485 option)

Weight Approx. 35g

Dimensions(mm) 38mm x 38mm x 3 Board

PIN HOLE, Board Lens,

DC IRIS(IR Remove) Vari focal lens, C/CS(DC\VIDEO)

OSD MANUAL

MENU DESCRIPTION

• The best clear image can be obtained color camera with

WDR(Wide Dynamic Range).

• The camera switches lenses automatically depending on the
illumination, which promotes the best possible color images
during the day and black / white image at night.

• The camera function can be controlled by OSD menu.

OSD STRUCTURE

▲,▼ :

•

Menu up / down

,▶ :

•

Menu left / right

◀

:

•

MENU

■

OSD MANUAL

OSD FUNCTION DESCRIPTION

1.LENS

: Enable user to select the lens type according to equipped with camera. Set up
using LEFT, RIGHT KEY at each menu.

- LENS TYPE
①ELC : Enable user to set up for BOARD lens.
②DC : Enable user to set up for DC Iris lens.
③VIDEO : Enable user to set up for VIDEO
Iris lens.

- LEVEL
: Enable user to select the level for Brightness
of image(0~15).

- INITIAL
: Enable user to initialize the LENS menu set up.

2. EXPOSURE

: Enable user to set up the function of SHUTTER, FLICKERLESS, AGC, DSS.
Set up using LEFT, RIGHT KEY at each menu.

- SHUTTER

: Enable user to set up the Shutter Speed

-> 1/60(50), 1/100(120), 1/250, 1/500, 1/1K,
1/2K, 1/4K, 1/10K, 1/100K
*() is for PAL TYPE

- FLICKERLESS
: Enable user to set up the FLICKERLESS ON/OFF.

- AGC
: Enable user to make image bright to amplify
the Gain.

-> LOW, MID, HIGH

- DSS(Digital Slow Shutter)
: Enable user to enhance video quality in extreme low-light condition to slow down

the shutter speed and collect over multiple elds based on the shutter limit setting.

-> OFF, 2X, 4X, 8X, 16X, 32X, 64X, 128X

- INITIAL
: Enable user to initialize the Exposure menu set up.

LENS

>LENS TYPE
LEVEL
INITIAL
RETURN

EXPOSURE

>SHUTTER
FLICKERLESS
AGC
DSS
INITIAL
RETURN

OSD MANUAL

3. WHITE BALANCE

: Enable user to represent the accurate white color by controlling the R,G,B level.
Setting up LEFT, RIGHT KEY on each menu.

- WB MODE

①

ATW : Enable user to trace the White Balance

automatically in the range of 2,300K~10,000K.

②

PUSH : Enable user to search for White Balance
automatically. In this mode, color temperature
range is broader than ATW.

③

...

DC

...

08

...

1/60

...

OFF

...

MID

...

10x

PUSH LOCK : Enable user to x the White

Balance according to the color temperature in
the certain environment.

④

MANUAL : Enable user to sets the White Balance
according to the circumstance.

- RED CONT: In the USER setting of WB MODE, enable user to set the RED GAIN.

- BLUE CONT:In the USER setting of WB MODE, enable user to set the BLUE GAIN.

- PUSH AUTO : In the PUSH LOCK setting of WB MODE, enable user to x the

White Balance in camera setting.

- INITIAL : Enable user to reset the WHITE BALANCE menu setting.

4. WDR/BLC

: Use the condition which Image doesn’t gure out with BLC such as place

surrounded windows and lobby. Set the WDR using the LEFT, RIGHT KEY on
the each menu.

- WDR MODE

①

OFF : None WDR

②

ON : WDR Fixed

- WDR LEVEL
: Enable user to set WDR Level(0~15 level).

- BLC(Back Light Compensation)
: Back Light Compensation

- BLC ZONE : Enable user to set the BLC area.
TOP, BOTTOM, CENTER, LEFT, RIGHT

- BLC LEVEL : Enable user to set BLC in selected
area(0~15 level).

- INITIAL : Enable user to initialize the WDR setting.

WHITE BALANCE

>WB MODE

RED CONT
BLUE CONT
PUSH CONT
INITIAL
RETURN

>WDR MODE
WDR LEVEL
BLC
BLC ZONE
BLC LEVEL
INITIAL
RETURN

WDR/BLC

...
...
...
...

...

...

ATW

...

----

...

----

...

----

OFF
08
OFF
CENTER

04

OSD MANUAL

5. DAY&NIGHT

: Conversion of output image COLOR / BW depending on exterior environment
Enable user to set the LEFT, RIGHT KEY in menu.

- D&N MODE
①COLOR : Enable user to x the output image
in color.
②B/W : Enable user to x the output image in B/W.
③AUTO : Enable user to convert to COLOR/BW
automatically
④EXT : Enable user to convert to COLOR/BW
by signal of the exterior input.

-> Low input signal : COLOR

-> High input signal : BW

- DETECT MODE
①AUTO : SENSOR + VIDEO Detection Mode
Enable user to convert to COLOR/BW by exterior sensor with illumination
②SENSOR : SENSOR Only Detection Mode
Enable user to convert to COLOR/BW automatically by exterior sensor
②VIDEO : VIDEO Only Detection Mode Enable user to convert to COLOR/BW
automatically by luminace element on Screen

- DWELL TIME : In D&N MODE AUTO, enable user to set to delay time for
changing COLOR/BW (0~10sec).

- D->N LEVEL : Day(Color) to Night(BW), level(0~19).

- N->D LEVEL : Night(BW) to Day, level(1~20).

- INITIAL : Enable user to initialize the setting in DAY&NIGHT menu.

SENSOR D->N / N-> D LEVEL

LEVEL LUX LEVEL LUX

0 1 Lux 11 12 Lux

1 2 Lux 12 13 Lux

2 3 Lux 13 14 Lux

3 4 Lux 14 15 Lux

4 5 Lux 15 16 Lux

5 6 Lux 16 17 Lux

6 7 Lux 17 18 Lux

7 8 Lux 18 19 Lux

8 9 Lux 19 20 Lux

9 10 Lux 20 21 Lux

10 11 Lux

DAY & NIGHT

>D&N MODE
DETECT MODE
DWELL TIME
D -> N LEVEL
N -> D LEVE
INITIAL
RETURN

...
...
...
...
...

COLOR

----

----

----

----

OSD MANUAL

6. IMAGE

: REVERSE, DNR, SHARPNESS, FREEZE,
D-ZOOM functions set up by pressing LEFT,
RIGHT KEY.

- REVERSE: Enable user to reverse the image.

-> NORMAL, H, V, H/V

- DNR : Reduces noise by using time-based ltering.

- DNR LEVEL : Enable user to set level(0~15 steps).

- SHARPNESS : Enable user to control the image sharpness (0~15steps).

- FREEZE : Enable user to freeze the image.

- D-ZOOM(Digital Zoom)

-> Max. 3x Digital Zoom.

- INITIAL : Enable user to initialize the setting on IMAGE menu.

IMAGE

>REVERSE
DNR ... OFF
DNR LEVEL ... 4
SHARPNESS
FREEZE
D-ZOOM
INITIAL
RETURN

...

...
...

...

NORMAL

10
OFF
1,0x

OSD MANUAL

7. SPECIAL

: Setting up the CAM TITLE, LANGUAGE,
COMM ADJ, PRIVACY,
MOTION DET, DISPLAY Set up using LEFT
and RIGHT key in each manual.

- CAM TITLE :
Enable user to choose any word in screen.
(Maximum 10 letter is available)

①

A letter Choice from the screen using Menu key.

②

Enable user to move to next menu using

LEFT, RIGHT KEY in LOCATION.

③

By using UP, DOWN, LEFT, RIGHT KEY,
enable user to choose any letters in
LOCATION and then get back to previous step.

④

Enable user to nish words choice and position

by using LEFT, RIGHT KEY in RETURN.

- LANGUAGE :
Enable user to set up an OSD language.

-> ENGLISH, CHINESE, RUSSIAN, SPANISH,
GERMAN

- COMM ADJ : Enable user to set up CAMERA ID,
BAUDRATE.

①

CAM ID: Enable user to set up Camera ID(0~255).

②

BAUDRATE: A communication speed to
Communicate with external device.
(2400, 4800, 9600, 19200).

- PRIVACY: Privacy is the function that covers
some part on screen to prevent private life
(Maximum 15 point covered).

①

ZONE: Enable user to set up positions from 0to14.

②

MASK: Enable user to set up screen output of
chosen position.

③

V START: Mask Vertical start position.

④

V END: Mask Vertical end position.

⑤

H START: Mask Horizontal start position.

⑥

H END: Mask Horizontal end position.

⑦

TOP ANGLE: Top angle position.

⑧

BOTTOM ANGLE: Bottom angle position.

⑨

INITIAL: Enable user to initialize setting of
PRIVACY MENU.

SPECIAL

CAM TITLE

>> <<BACK

[TITLE LOCATION]

...
...
...

...
...

...

...

[-]
ENGLISH
[-]

[-]
[-]

[-]

[-]

>CAM TITLE
LANGUAGE
COMM ADJ
PRIVACY
MOTION DETECT
DISPLAY
INITIAL
RETURN

0123456789ABCDEFGHIJKLMN
OPQRSTUVWXYZ!?*#$%()<>{}

SPACE

LOCATION
RETURN

TITLE

[U] [D] [L] [R] [M] +

CAMM ADJ

PRIVACY

...
...

...
...

...

>CAM ID
BAUDRATE
RETURN

>ZONE NO
MASK
V START ... 07
V END ... 12
H START ... 10
H END ... 19
TOP ANGLE ... 00
BOTTOM ANGLE
INITIAL
RETURN

000
9600

0
OFF

00

OSD MANUAL

- MOTION DET : Motion detection and Face
detection function.

①

MOTION MODE : Enable user to set up ON/OFF.

②

LEVEL : Enable user to setup a motion detect

sensitivity (0~15).

③

FACE MODE : Enable user to set up ON/OFF.

④

LEVEL : Enable user to set up a face detect

sensitivity (0~15).

⑤

V START : Mask Vertical start position.

⑥

V END : Mask Vertical end position.

⑦

H START : Mask Horizontal start position.

⑧

H END : Mask Horizontal end position.

⑨

INITIAL : Enable user to initialize setting

of MOTION DETECT.

- DISPLAY : Enable user to set up a screen marking
of CAM ID, CAM TITLE, MOTION,FACE
① CAM ID : Enable user to set up output on
Camera ID screen.
② CAM TITLE : Enable user to set up output in

xed CAM TITLE.

③ MOTION DETECT : Enable user to set up out
put of MOTION on the screen as
MOTION DET ON setting.
③ FACE DETECT : Enable user to set up out
put of FACE on the screen as
FACE DETECT ON setting.
④ INITIAL : Enable user to initialize of DISPLAY menu.

8. FACTORY DEFAULT

: Enable user to reset all of the status as the factory default
Setting up using LEFT, RIGHT KEY.

9. EXIT

: Enable user to EXIT the OSD menu Setting up using LEFT, RIGHT KEY.

MOTION DET

>MOTION MODE
LEVEL
FACE MODE ... ON
LEVEL ... 07
V START ... 01
V END ... 06
H START ... 01
H END ... 10
INITIAL
RETURN

DISPLAY

>CAM ID
CAM TITLE
MOTION DETECT
FACE DETECT
INITIAL
RETURN

...

ON

...

08

...

OFF

...

OFF

...

OFF

...

OFF

M092-EDR380-001

HIGH RESOLUTION

WDR COLOR MODULE CAMERA

OPERATION MANUAL

Thank you for choosing our high quality camera.
Before attempting to connect or operate, please read and
follow these instructions.

CAUTIONS

This device complies with Part 15 of the FCC Rules.
Operation is subject to the following two conditions;

1. This device may not cause harmful interference.

2. This device must accept any interference received, including
interference that may cause undesired operation.

Note -

This equipment has been tested and found to comply with the
limits for a Class A digital device, pursuant to part 15 of the FCC
Rules. These limits are designed to provide reasonable protection
against harmful interference when the equipment is operated in
a commercial environment. This equipment generates, uses, and
can radiate radio frequency energy and, if not installed and used
in accordance with the instruction manual, may cause harmful
interference to radio communications. Operation of this equipment
in a residential area is likely to cause harmful interference in which
case the user will be required to correct the interference at his own
expense.”

WARNING -

This is a class A product. In a domestic environment this product
may cause radio interference in which case the user may be
required to take adequate measures.

Caution -

Any changes or modications in construction of this devies which

are not expressly approved by the party responsible for compliance
could void the user's authority to operate the equipment.

1. A regulated DC12V 300mA power supply is recommended for use with
this camera for the best picture and the most stable operation.

An unregulated power supply can cause damage to the camera.
When unregulated power supply is applied, product warranty will be
out of subject.

2. It is recommended that the camera is used with a monitor that has a
CCTV quality 75 video impedance level. If your monitor is switched to high
impedance then please adjust accordingly.

3. Do not attempt to disassemble the camera to gain access to the internal
componets. Refer servicing to your dealer.

4. Never face the camera towards the sun or any bright or reective light,

which may cause smear on the picture and possible damage to the CCD.

5. Do not remove the serial sticker for the warranty service.

CAUTION

CAUTIONS

Correct Disposal of This Product

(Waste Electrical & Electronic Equipment)

(Applicable in the European Union and other European
countries with separate collection systems)

This marking shown on the product or its literature, indicate that
it should not be disposed with other household wastes at the end
of its working life. To prevent possible harm to the environment or
human health from uncontrolled waste disposal, please separate
this from other types of wastes and recycle it responsibly to promote
the sustainable reuse of material resources.

This product should not be mixed with other commercial wastes

purchased this product, or their local government ofce, for details

of where and how they can take item for environmentally safe
recycling.

Business users should contact their supplier and check the terms
and conditions of the purchase contract.
Household users should contact either the retailer where they for
disposal.

RISK OF ELECTRIC SHOCK DO NOT OPEN

CAUTION : TO REDUCE THE RISK OF ELECTRIC SHOCK, DO

NOT REMOVE COVER(OR BACK). NO USER.
SERVICING TO QUALIFED SERVICE PERSONNEL.

This symbol is intended to alert the user to the presence
of uninsulated "dangerous voltage" within the product's

enclosure that may be of sufcient mangnitude to constitute

a risk of electric shock to persons.

This symbol is intended to alert the user to the presence of
important operating and maintenance(servicing) instruction in
the literature accompanying the appliance.

CAUTION

FEATURES

• 1/3 960H SONY Double Scan Super HAD CCD II

• High Resolution of 700TV Lines

• WDR (Wide Dynamic Range)

• OSD Function

• Multi Language
(English / Chinese / Russian / Spanish / German)

• Digital slow shutter

• 3DNR

• Privacy Zone 15Zone

• 3x Digital Zoom

• Motion Detect, Face Detection

• Only DC12V

• RS-232C TTL Level Interface(RS-485 Option)

• A/D Remote Controller > Option

How WDR makes better image?

WDR allows every detail to be captured accurately even
if one portion is bright while other portions are dark.

Option(Lens.A/D Remocom)

Pin Hole

Lens Type

Function

SW1 : MENU OSD Menu on/off
SW2 : UP OSD Menu up
SW3 : DOWN OSD Menu down
SW4 : LEFT OSD Menu left
SW5 : RIGHT OSD Menu right

Option

Board

Varlfocal

C/CS Mount

CONNECTION DIMENSIONS

SENSOR

1) J103(DC IRIS)

2) J105(IR CUT)

3) J506(DC IRIS)

J103 J105

Top Connector Position

PIN NO. NAME I/O

1 DAMP + O

2 DAMP - O

3 DRV + O

4 GND -

PIN NO. NAME I/O

1 IR CUT OUT + O

2 IR CUT OUT - O

PIN NO. NAME I/O

1 DAMP + O

2 DAMP - O

3 DRV + O

4 GND -

Bottom Connector Position

J508 J507 J506

CONNECTION

4) J507(DN_I/O)

PIN NO. NAME I/O

1 +12V O

2 GND -

3 COLOR/BW IN I

4 COLOR/BW OUT O

5) J508(DN_I/O)

PIN NO. NAME I/O

1 GND -

2 VIDEO O

3 GND -

4 +12V I

5 RXD(TRX-) I/O

6 TXD(TRX+) I/O

7 A/D KEY1 I

8 MOTION O

9 COLOR/BW IN I

10 GND -

COLOR/BW IN Application

Color/BW IN

OPEN: NIGHT MODE
GND: DAY MODE

RS232C TTL LEVEL

HIGH : +3.3V
LOW : GND

Unit(mm)

2-5.0

Control Function

LEFT

Color/BW IN

MENU

13.6

29.8

- BOTTOM VIEW -

UP

DOWN

38

38

- TOP VIEW -

RIGHT

SPECIFICATION

Signal Format NTSC PAL

Image Device 1/3” 960H SONY Double Scan Super HAD CCD II

Scanning System 2:1 Interlace

H.Resolution 750TV Lines

Scanning Frequency H:15.734KHz, V:59.94Hz H:15.625KHz, V:50Hz

Total Pixels 1028(H) X 508(V) 1028(H) X 596(V)

Effective Pixels 976(H) X 494(V) 976(H) X 582(V)

Electronic Shutter 1/60 ~1/100,000sec 1/50 ~1/100,000sec

Digital Zoom Ratio 3x

Digital Slow Shutter OFF, 2 ~ 128 Field

Flickerless ON / OFF

WDR ON / OFF (Level adjustable)

BLC ON / OFF (Level adjustment, Area selection)

3DNR ON / OFF (Level adjustable)

Image Function Image reverse(NORMAL/H / V / HV), Freeze

Sharpness Level adjustable

AGC LOW / MID / HIGH

Day & Night COLOR / BW / AUTO / EXT

Motion Detection ON / OFF (Level adjustable, Area adjustment)

Face Detection ON / OFF (Level adjustable, Area adjustment)

Privacy Masking 15 Zones (Area adjustment)

White Balance ATW / PUSH / PUSH LOCK / MANUAL(R Gain, B Gain)

OSD Built in

Language English / Chinese / Russian / Spanish / German

Protocol Pelco"D"

Baud Rate 2400 / 4800 / 9600 / 19200

S/N Ratio More than 50dB(AGC OFF, 3DNR ON)

Gamma r=0.45

Min. Illumination 0.08Lux(Color) / 0.04Lux(BW) (30IRE@F1.2, AGC:HIGH)

Sync System Internal

SPECIFICATION

Video Output 1.0 Vp-p Composite 75(Ω) unbalanced

Lens

Power Consumption DC 12V ±10%, Max 170mA

OperatingTemperature 14°F~122°F(-10°C~+50°C)

Storage Temperature -4°F~140°F(-20°C~+60°C)

Humidity Less than 80%

External Control A/D KEY, RS232C TTL(RS485 option)

Weight Approx. 35g

Dimensions(mm) 38mm x 38mm x 3 Board

PIN HOLE, Board Lens,

DC IRIS(IR Remove) Vari focal lens, C/CS(DC\VIDEO)

OSD MANUAL

MENU DESCRIPTION

• The best clear image can be obtained color camera with

WDR(Wide Dynamic Range).

• The camera switches lenses automatically depending on the
illumination, which promotes the best possible color images
during the day and black / white image at night.

• The camera function can be controlled by OSD menu.

OSD STRUCTURE

▲,▼ :

•

Menu up / down

,▶ :

•

Menu left / right

◀

:

•

MENU

■

OSD MANUAL

OSD FUNCTION DESCRIPTION

1.LENS

: Enable user to select the lens type according to equipped with camera. Set up
using LEFT, RIGHT KEY at each menu.

- LENS TYPE
①ELC : Enable user to set up for BOARD lens.
②DC : Enable user to set up for DC Iris lens.
③VIDEO : Enable user to set up for VIDEO
Iris lens.

- LEVEL
: Enable user to select the level for Brightness
of image(0~15).

- INITIAL
: Enable user to initialize the LENS menu set up.

2. EXPOSURE

: Enable user to set up the function of SHUTTER, FLICKERLESS, AGC, DSS.
Set up using LEFT, RIGHT KEY at each menu.

- SHUTTER

: Enable user to set up the Shutter Speed

-> 1/60(50), 1/100(120), 1/250, 1/500, 1/1K,
1/2K, 1/4K, 1/10K, 1/100K
*() is for PAL TYPE

- FLICKERLESS
: Enable user to set up the FLICKERLESS ON/OFF.

- AGC
: Enable user to make image bright to amplify
the Gain.

-> LOW, MID, HIGH

- DSS(Digital Slow Shutter)
: Enable user to enhance video quality in extreme low-light condition to slow down

the shutter speed and collect over multiple elds based on the shutter limit setting.

-> OFF, 2X, 4X, 8X, 16X, 32X, 64X, 128X

- INITIAL
: Enable user to initialize the Exposure menu set up.

LENS

>LENS TYPE
LEVEL
INITIAL
RETURN

EXPOSURE

>SHUTTER
FLICKERLESS
AGC
DSS
INITIAL
RETURN

OSD MANUAL

3. WHITE BALANCE

: Enable user to represent the accurate white color by controlling the R,G,B level.
Setting up LEFT, RIGHT KEY on each menu.

- WB MODE

①

ATW : Enable user to trace the White Balance

automatically in the range of 2,300K~10,000K.

②

PUSH : Enable user to search for White Balance
automatically. In this mode, color temperature
range is broader than ATW.

③

...

DC

...

08

...

1/60

...

OFF

...

MID

...

10x

PUSH LOCK : Enable user to x the White

Balance according to the color temperature in
the certain environment.

④

MANUAL : Enable user to sets the White Balance
according to the circumstance.

- RED CONT: In the USER setting of WB MODE, enable user to set the RED GAIN.

- BLUE CONT:In the USER setting of WB MODE, enable user to set the BLUE GAIN.

- PUSH AUTO : In the PUSH LOCK setting of WB MODE, enable user to x the

White Balance in camera setting.

- INITIAL : Enable user to reset the WHITE BALANCE menu setting.

4. WDR/BLC

: Use the condition which Image doesn’t gure out with BLC such as place

surrounded windows and lobby. Set the WDR using the LEFT, RIGHT KEY on
the each menu.

- WDR MODE

①

OFF : None WDR

②

ON : WDR Fixed

- WDR LEVEL
: Enable user to set WDR Level(0~15 level).

- BLC(Back Light Compensation)
: Back Light Compensation

- BLC ZONE : Enable user to set the BLC area.
TOP, BOTTOM, CENTER, LEFT, RIGHT

- BLC LEVEL : Enable user to set BLC in selected
area(0~15 level).

- INITIAL : Enable user to initialize the WDR setting.

WHITE BALANCE

>WB MODE

RED CONT
BLUE CONT
PUSH CONT
INITIAL
RETURN

>WDR MODE
WDR LEVEL
BLC
BLC ZONE
BLC LEVEL
INITIAL
RETURN

WDR/BLC

...
...
...
...

...

...

ATW

...

----

...

----

...

----

OFF
08
OFF
CENTER

04

OSD MANUAL

5. DAY&NIGHT

: Conversion of output image COLOR / BW depending on exterior environment
Enable user to set the LEFT, RIGHT KEY in menu.

- D&N MODE
①COLOR : Enable user to x the output image
in color.
②B/W : Enable user to x the output image in B/W.
③AUTO : Enable user to convert to COLOR/BW
automatically
④EXT : Enable user to convert to COLOR/BW
by signal of the exterior input.

-> Low input signal : COLOR

-> High input signal : BW

- DETECT MODE
①AUTO : SENSOR + VIDEO Detection Mode
Enable user to convert to COLOR/BW by exterior sensor with illumination
②SENSOR : SENSOR Only Detection Mode
Enable user to convert to COLOR/BW automatically by exterior sensor
②VIDEO : VIDEO Only Detection Mode Enable user to convert to COLOR/BW
automatically by luminace element on Screen

- DWELL TIME : In D&N MODE AUTO, enable user to set to delay time for
changing COLOR/BW (0~10sec).

- D->N LEVEL : Day(Color) to Night(BW), level(0~19).

- N->D LEVEL : Night(BW) to Day, level(1~20).

- INITIAL : Enable user to initialize the setting in DAY&NIGHT menu.

SENSOR D->N / N-> D LEVEL

LEVEL LUX LEVEL LUX

0 1 Lux 11 12 Lux

1 2 Lux 12 13 Lux

2 3 Lux 13 14 Lux

3 4 Lux 14 15 Lux

4 5 Lux 15 16 Lux

5 6 Lux 16 17 Lux

6 7 Lux 17 18 Lux

7 8 Lux 18 19 Lux

8 9 Lux 19 20 Lux

9 10 Lux 20 21 Lux

10 11 Lux

DAY & NIGHT

>D&N MODE
DETECT MODE
DWELL TIME
D -> N LEVEL
N -> D LEVE
INITIAL
RETURN

...
...
...
...
...

COLOR

----

----

----

----

OSD MANUAL

6. IMAGE

: REVERSE, DNR, SHARPNESS, FREEZE,
D-ZOOM functions set up by pressing LEFT,
RIGHT KEY.

- REVERSE: Enable user to reverse the image.

-> NORMAL, H, V, H/V

- DNR : Reduces noise by using time-based ltering.

- DNR LEVEL : Enable user to set level(0~15 steps).

- SHARPNESS : Enable user to control the image sharpness (0~15steps).

- FREEZE : Enable user to freeze the image.

- D-ZOOM(Digital Zoom)

-> Max. 3x Digital Zoom.

- INITIAL : Enable user to initialize the setting on IMAGE menu.

IMAGE

>REVERSE
DNR ... OFF
DNR LEVEL ... 4
SHARPNESS
FREEZE
D-ZOOM
INITIAL
RETURN

...

...
...

...

NORMAL

10
OFF
1,0x

OSD MANUAL

7. SPECIAL

: Setting up the CAM TITLE, LANGUAGE,
COMM ADJ, PRIVACY,
MOTION DET, DISPLAY Set up using LEFT
and RIGHT key in each manual.

- CAM TITLE :
Enable user to choose any word in screen.
(Maximum 10 letter is available)

①

A letter Choice from the screen using Menu key.

②

Enable user to move to next menu using

LEFT, RIGHT KEY in LOCATION.

③

By using UP, DOWN, LEFT, RIGHT KEY,
enable user to choose any letters in
LOCATION and then get back to previous step.

④

Enable user to nish words choice and position

by using LEFT, RIGHT KEY in RETURN.

- LANGUAGE :
Enable user to set up an OSD language.

-> ENGLISH, CHINESE, RUSSIAN, SPANISH,
GERMAN

- COMM ADJ : Enable user to set up CAMERA ID,
BAUDRATE.

①

CAM ID: Enable user to set up Camera ID(0~255).

②

BAUDRATE: A communication speed to
Communicate with external device.
(2400, 4800, 9600, 19200).

- PRIVACY: Privacy is the function that covers
some part on screen to prevent private life
(Maximum 15 point covered).

①

ZONE: Enable user to set up positions from 0to14.

②

MASK: Enable user to set up screen output of
chosen position.

③

V START: Mask Vertical start position.

④

V END: Mask Vertical end position.

⑤

H START: Mask Horizontal start position.

⑥

H END: Mask Horizontal end position.

⑦

TOP ANGLE: Top angle position.

⑧

BOTTOM ANGLE: Bottom angle position.

⑨

INITIAL: Enable user to initialize setting of
PRIVACY MENU.

SPECIAL

CAM TITLE

>> <<BACK

[TITLE LOCATION]

...
...
...

...
...

...

...

[-]
ENGLISH
[-]

[-]
[-]

[-]

[-]

>CAM TITLE
LANGUAGE
COMM ADJ
PRIVACY
MOTION DETECT
DISPLAY
INITIAL
RETURN

0123456789ABCDEFGHIJKLMN
OPQRSTUVWXYZ!?*#$%()<>{}

SPACE

LOCATION
RETURN

TITLE

[U] [D] [L] [R] [M] +

CAMM ADJ

PRIVACY

...
...

...
...

...

>CAM ID
BAUDRATE
RETURN

>ZONE NO
MASK
V START ... 07
V END ... 12
H START ... 10
H END ... 19
TOP ANGLE ... 00
BOTTOM ANGLE
INITIAL
RETURN

000
9600

0
OFF

00

OSD MANUAL

- MOTION DET : Motion detection and Face
detection function.

①

MOTION MODE : Enable user to set up ON/OFF.

②

LEVEL : Enable user to setup a motion detect

sensitivity (0~15).

③

FACE MODE : Enable user to set up ON/OFF.

④

LEVEL : Enable user to set up a face detect

sensitivity (0~15).

⑤

V START : Mask Vertical start position.

⑥

V END : Mask Vertical end position.

⑦

H START : Mask Horizontal start position.

⑧

H END : Mask Horizontal end position.

⑨

INITIAL : Enable user to initialize setting

of MOTION DETECT.

- DISPLAY : Enable user to set up a screen marking
of CAM ID, CAM TITLE, MOTION,FACE
① CAM ID : Enable user to set up output on
Camera ID screen.
② CAM TITLE : Enable user to set up output in

xed CAM TITLE.

③ MOTION DETECT : Enable user to set up out
put of MOTION on the screen as
MOTION DET ON setting.
③ FACE DETECT : Enable user to set up out
put of FACE on the screen as
FACE DETECT ON setting.
④ INITIAL : Enable user to initialize of DISPLAY menu.

8. FACTORY DEFAULT

: Enable user to reset all of the status as the factory default
Setting up using LEFT, RIGHT KEY.

9. EXIT

: Enable user to EXIT the OSD menu Setting up using LEFT, RIGHT KEY.

MOTION DET

>MOTION MODE
LEVEL
FACE MODE ... ON
LEVEL ... 07
V START ... 01
V END ... 06
H START ... 01
H END ... 10
INITIAL
RETURN

DISPLAY

>CAM ID
CAM TITLE
MOTION DETECT
FACE DETECT
INITIAL
RETURN

...

ON

...

08

...

OFF

...

OFF

...

OFF

...

OFF

SPECIFICATION

Signal Format NTSC PAL

Image Device 1/3” 960H SONY Double Scan Super HAD CCD II

Scanning System 2:1 Interlace

H.Resolution 750TV Lines

Scanning Frequency H:15.734KHz, V:59.94Hz H:15.625KHz, V:50Hz

Total Pixels 1028(H) X 508(V) 1028(H) X 596(V)

Effective Pixels 976(H) X 494(V) 976(H) X 582(V)

Electronic Shutter 1/60 ~1/100,000sec 1/50 ~1/100,000sec

Digital Zoom Ratio 3x

Digital Slow Shutter OFF, 2 ~ 128 Field

Flickerless ON / OFF

WDR ON / OFF (Level adjustable)

BLC ON / OFF (Level adjustment, Area selection)

3DNR ON / OFF (Level adjustable)

Image Function Image reverse(NORMAL/H / V / HV), Freeze

Sharpness Level adjustable

AGC LOW / MID / HIGH

Day & Night COLOR / BW / AUTO / EXT

Motion Detection ON / OFF (Level adjustable, Area adjustment)

Face Detection ON / OFF (Level adjustable, Area adjustment)

Privacy Masking 15 Zones (Area adjustment)

White Balance ATW / PUSH / PUSH LOCK / MANUAL(R Gain, B Gain)

OSD Built in

Language English / Chinese / Russian / Spanish / German

Protocol Pelco"D"

Baud Rate 2400 / 4800 / 9600 / 19200

S/N Ratio More than 50dB(AGC OFF, 3DNR ON)

Gamma r=0.45

Min. Illumination 0.08Lux(Color) / 0.04Lux(BW) (30IRE@F1.2, AGC:HIGH)

Sync System Internal

SPECIFICATION

Video Output 1.0 Vp-p Composite 75(Ω) unbalanced

Lens

Power Consumption DC 12V ±10%, Max 170mA

OperatingTemperature 14°F~122°F(-10°C~+50°C)

Storage Temperature -4°F~140°F(-20°C~+60°C)

Humidity Less than 80%

External Control A/D KEY, RS232C TTL(RS485 option)

Weight Approx. 35g

Dimensions(mm) 38mm x 38mm x 3 Board

PIN HOLE, Board Lens,

DC IRIS(IR Remove) Vari focal lens, C/CS(DC\VIDEO)

OSD MANUAL

MENU DESCRIPTION

• The best clear image can be obtained color camera with

WDR(Wide Dynamic Range).

• The camera switches lenses automatically depending on the
illumination, which promotes the best possible color images
during the day and black / white image at night.

• The camera function can be controlled by OSD menu.

OSD STRUCTURE

▲,▼ :

•

Menu up / down

,▶ :

•

Menu left / right

◀

:

•

MENU

■

OSD MANUAL

OSD FUNCTION DESCRIPTION

1.LENS

: Enable user to select the lens type according to equipped with camera. Set up
using LEFT, RIGHT KEY at each menu.

- LENS TYPE
①ELC : Enable user to set up for BOARD lens.
②DC : Enable user to set up for DC Iris lens.
③VIDEO : Enable user to set up for VIDEO
Iris lens.

- LEVEL
: Enable user to select the level for Brightness
of image(0~15).

- INITIAL
: Enable user to initialize the LENS menu set up.

2. EXPOSURE

: Enable user to set up the function of SHUTTER, FLICKERLESS, AGC, DSS.
Set up using LEFT, RIGHT KEY at each menu.

- SHUTTER

: Enable user to set up the Shutter Speed

-> 1/60(50), 1/100(120), 1/250, 1/500, 1/1K,
1/2K, 1/4K, 1/10K, 1/100K
*() is for PAL TYPE

- FLICKERLESS
: Enable user to set up the FLICKERLESS ON/OFF.

- AGC
: Enable user to make image bright to amplify
the Gain.

-> LOW, MID, HIGH

- DSS(Digital Slow Shutter)
: Enable user to enhance video quality in extreme low-light condition to slow down

the shutter speed and collect over multiple elds based on the shutter limit setting.

-> OFF, 2X, 4X, 8X, 16X, 32X, 64X, 128X

- INITIAL
: Enable user to initialize the Exposure menu set up.

LENS

>LENS TYPE
LEVEL
INITIAL
RETURN

EXPOSURE

>SHUTTER
FLICKERLESS
AGC
DSS
INITIAL
RETURN

OSD MANUAL

3. WHITE BALANCE

: Enable user to represent the accurate white color by controlling the R,G,B level.
Setting up LEFT, RIGHT KEY on each menu.

- WB MODE

①

ATW : Enable user to trace the White Balance

automatically in the range of 2,300K~10,000K.

②

PUSH : Enable user to search for White Balance
automatically. In this mode, color temperature
range is broader than ATW.

③

...

DC

...

08

...

1/60

...

OFF

...

MID

...

10x

PUSH LOCK : Enable user to x the White

Balance according to the color temperature in
the certain environment.

④

MANUAL : Enable user to sets the White Balance
according to the circumstance.

- RED CONT: In the USER setting of WB MODE, enable user to set the RED GAIN.

- BLUE CONT:In the USER setting of WB MODE, enable user to set the BLUE GAIN.

- PUSH AUTO : In the PUSH LOCK setting of WB MODE, enable user to x the

White Balance in camera setting.

- INITIAL : Enable user to reset the WHITE BALANCE menu setting.

4. WDR/BLC

: Use the condition which Image doesn’t gure out with BLC such as place

surrounded windows and lobby. Set the WDR using the LEFT, RIGHT KEY on
the each menu.

- WDR MODE

①

OFF : None WDR

②

ON : WDR Fixed

- WDR LEVEL
: Enable user to set WDR Level(0~15 level).

- BLC(Back Light Compensation)
: Back Light Compensation

- BLC ZONE : Enable user to set the BLC area.
TOP, BOTTOM, CENTER, LEFT, RIGHT

- BLC LEVEL : Enable user to set BLC in selected
area(0~15 level).

- INITIAL : Enable user to initialize the WDR setting.

WHITE BALANCE

>WB MODE

RED CONT
BLUE CONT
PUSH CONT
INITIAL
RETURN

>WDR MODE
WDR LEVEL
BLC
BLC ZONE
BLC LEVEL
INITIAL
RETURN

WDR/BLC

...
...
...
...

...

...

ATW

...

----

...

----

...

----

OFF
08
OFF
CENTER

04

OSD MANUAL

5. DAY&NIGHT

: Conversion of output image COLOR / BW depending on exterior environment
Enable user to set the LEFT, RIGHT KEY in menu.

- D&N MODE
①COLOR : Enable user to x the output image
in color.
②B/W : Enable user to x the output image in B/W.
③AUTO : Enable user to convert to COLOR/BW
automatically
④EXT : Enable user to convert to COLOR/BW
by signal of the exterior input.

-> Low input signal : COLOR

-> High input signal : BW

- DETECT MODE
①AUTO : SENSOR + VIDEO Detection Mode
Enable user to convert to COLOR/BW by exterior sensor with illumination
②SENSOR : SENSOR Only Detection Mode
Enable user to convert to COLOR/BW automatically by exterior sensor
②VIDEO : VIDEO Only Detection Mode Enable user to convert to COLOR/BW
automatically by luminace element on Screen

- DWELL TIME : In D&N MODE AUTO, enable user to set to delay time for
changing COLOR/BW (0~10sec).

- D->N LEVEL : Day(Color) to Night(BW), level(0~19).

- N->D LEVEL : Night(BW) to Day, level(1~20).

- INITIAL : Enable user to initialize the setting in DAY&NIGHT menu.

SENSOR D->N / N-> D LEVEL

LEVEL LUX LEVEL LUX

0 1 Lux 11 12 Lux

1 2 Lux 12 13 Lux

2 3 Lux 13 14 Lux

3 4 Lux 14 15 Lux

4 5 Lux 15 16 Lux

5 6 Lux 16 17 Lux

6 7 Lux 17 18 Lux

7 8 Lux 18 19 Lux

8 9 Lux 19 20 Lux

9 10 Lux 20 21 Lux

10 11 Lux

DAY & NIGHT

>D&N MODE
DETECT MODE
DWELL TIME
D -> N LEVEL
N -> D LEVE
INITIAL
RETURN

...
...
...
...
...

COLOR

----

----

----

----

OSD MANUAL

6. IMAGE

: REVERSE, DNR, SHARPNESS, FREEZE,
D-ZOOM functions set up by pressing LEFT,
RIGHT KEY.

- REVERSE: Enable user to reverse the image.

-> NORMAL, H, V, H/V

- DNR : Reduces noise by using time-based ltering.

- DNR LEVEL : Enable user to set level(0~15 steps).

- SHARPNESS : Enable user to control the image sharpness (0~15steps).

- FREEZE : Enable user to freeze the image.

- D-ZOOM(Digital Zoom)

-> Max. 3x Digital Zoom.

- INITIAL : Enable user to initialize the setting on IMAGE menu.

IMAGE

>REVERSE
DNR ... OFF
DNR LEVEL ... 4
SHARPNESS
FREEZE
D-ZOOM
INITIAL
RETURN

...

...
...

...

NORMAL

10
OFF
1,0x

OSD MANUAL

7. SPECIAL

: Setting up the CAM TITLE, LANGUAGE,
COMM ADJ, PRIVACY,
MOTION DET, DISPLAY Set up using LEFT
and RIGHT key in each manual.

- CAM TITLE :
Enable user to choose any word in screen.
(Maximum 10 letter is available)

①

A letter Choice from the screen using Menu key.

②

Enable user to move to next menu using

LEFT, RIGHT KEY in LOCATION.

③

By using UP, DOWN, LEFT, RIGHT KEY,
enable user to choose any letters in
LOCATION and then get back to previous step.

④

Enable user to nish words choice and position

by using LEFT, RIGHT KEY in RETURN.

- LANGUAGE :
Enable user to set up an OSD language.

-> ENGLISH, CHINESE, RUSSIAN, SPANISH,
GERMAN

- COMM ADJ : Enable user to set up CAMERA ID,
BAUDRATE.

①

CAM ID: Enable user to set up Camera ID(0~255).

②

BAUDRATE: A communication speed to
Communicate with external device.
(2400, 4800, 9600, 19200).

- PRIVACY: Privacy is the function that covers
some part on screen to prevent private life
(Maximum 15 point covered).

①

ZONE: Enable user to set up positions from 0to14.

②

MASK: Enable user to set up screen output of
chosen position.

③

V START: Mask Vertical start position.

④

V END: Mask Vertical end position.

⑤

H START: Mask Horizontal start position.

⑥

H END: Mask Horizontal end position.

⑦

TOP ANGLE: Top angle position.

⑧

BOTTOM ANGLE: Bottom angle position.

⑨

INITIAL: Enable user to initialize setting of
PRIVACY MENU.

SPECIAL

CAM TITLE

>> <<BACK

[TITLE LOCATION]

...
...
...

...
...

...

...

[-]
ENGLISH
[-]

[-]
[-]

[-]

[-]

>CAM TITLE
LANGUAGE
COMM ADJ
PRIVACY
MOTION DETECT
DISPLAY
INITIAL
RETURN

0123456789ABCDEFGHIJKLMN
OPQRSTUVWXYZ!?*#$%()<>{}

SPACE

LOCATION
RETURN

TITLE

[U] [D] [L] [R] [M] +

CAMM ADJ

PRIVACY

...
...

...
...

...

>CAM ID
BAUDRATE
RETURN

>ZONE NO
MASK
V START ... 07
V END ... 12
H START ... 10
H END ... 19
TOP ANGLE ... 00
BOTTOM ANGLE
INITIAL
RETURN

000
9600

0
OFF

00

OSD MANUAL

- MOTION DET : Motion detection and Face
detection function.

①

MOTION MODE : Enable user to set up ON/OFF.

②

LEVEL : Enable user to setup a motion detect

sensitivity (0~15).

③

FACE MODE : Enable user to set up ON/OFF.

④

LEVEL : Enable user to set up a face detect

sensitivity (0~15).

⑤

V START : Mask Vertical start position.

⑥

V END : Mask Vertical end position.

⑦

H START : Mask Horizontal start position.

⑧

H END : Mask Horizontal end position.

⑨

INITIAL : Enable user to initialize setting

of MOTION DETECT.

- DISPLAY : Enable user to set up a screen marking
of CAM ID, CAM TITLE, MOTION,FACE
① CAM ID : Enable user to set up output on
Camera ID screen.
② CAM TITLE : Enable user to set up output in

xed CAM TITLE.

③ MOTION DETECT : Enable user to set up out
put of MOTION on the screen as
MOTION DET ON setting.
③ FACE DETECT : Enable user to set up out
put of FACE on the screen as
FACE DETECT ON setting.
④ INITIAL : Enable user to initialize of DISPLAY menu.

8. FACTORY DEFAULT

: Enable user to reset all of the status as the factory default
Setting up using LEFT, RIGHT KEY.

9. EXIT

: Enable user to EXIT the OSD menu Setting up using LEFT, RIGHT KEY.

MOTION DET

>MOTION MODE
LEVEL
FACE MODE ... ON
LEVEL ... 07
V START ... 01
V END ... 06
H START ... 01
H END ... 10
INITIAL
RETURN

DISPLAY

>CAM ID
CAM TITLE
MOTION DETECT
FACE DETECT
INITIAL
RETURN

...

ON

...

08

...

OFF

...

OFF

...

OFF

...

OFF