How it Works
KT&C
Loading...
550TVL
Operation Manual
40 pgs1.6 Mb0

KT&C 550TVL, KPC-ZA360WN Operation Manual

Download
M064-ZA360-001
Be fo re i ns ta ll in g and us in g the camera, please read this manual carefully. Be sure to keep it handy for later reference.
About th is ma nual
OPE RATIO N M AN UAL
3 6 0 X AU TO F O C U S
CONTE N TS
1. Ca uti on s
2. Pr eca ut ion s
3. Fe atu re s
4. Co mpo ne nts and Acc es sor ies
• Pack ag e
• Tri po d Mou nt in g
5. Di men si ons
6. Ov erv ie w
• Rea r View
7. In sta ll ati on
• Con ne cting t o Monit or
• Con ne cting t o Power
• Con ne cting t o Conne ct ion
8. Op era ti ng Camer a
• OSD M enu C on fi gurat io n
• On Sc reen Di sp lay(O SD )
• Men u Setup
- L ENS
- E XPO SUR E
- W HIT E B AL ANC E
- W DR( *)/ BL C
- D AY & N IG HT
- I MAG E
- S PEC IAL
_ TIT L E _ PRI V ACY _ DIS P LAY _ MOT I ON D ETE C T
9. Co mmu ni cat ion P rot oc ol
10. S pec if ica tions
3
(*) CAUTION : The W DR is an Opti ona l fun ction
1.Cau t ions
INFORMATION
This equipment has been tested and found to comply with limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at their own expense.
WARNING
Any Changes or modications in construction of this devices which are
not expressly approved by the party responsible for compliance could void the authority to operate the equipment.
CAUTION :
To prevent electric shock and risk of re hazards:
- Do NOT use power sources except for that specied.
- Do NOT expose this appliance to rain or moisture.
4
Correct Disposal of This Product
(Waste Electrical & Electronic Equipment)
(Applicable in the European Union and other European countries with separate collection systems)
This marking shown on the product or its literature, indicate that it should not be disposed with other household wastes at the end of its working life. To prevent possible harm to the environment or human health from uncontrolled waste disposal, please separate this from other types of wastes and recycle it responsibly to promote the sustainable reuse of material resources.
This product should not be mixed with other commercial wastes purchased this
product, or their local government ofce, for details of where and how they can
take item for environmentally safe recycling.
Business users should contact their supplier and check the terms and conditions of the purchase contract. Household users should contact either the retailer where they for disposal.
1. A regulated DC12V 500mA power supply is recommended for use with this camera for the best picture and the most stable operation. An unregulated power supply can cause damage to the camera.
When unregulated power supply is applied, product warranty will be out of subject.
2. It is recommended that the camera is used with a monitor that has a CCTV quality 75 video impedance level. If your monitor is switched to high impedance then please adjust accordingly.
3. Do not attempt to disassemble the camera to gain access to the internal components. Refer servicing to your dealer.
4. Never face the camera towards the sun or any bright or reective light, which may
cause smear on the picture and possible damage to the CCD.
5. Do not remove the serial sticker for the warranty service.
NOTE
1.Cau t ions
5
CAUTIONS
1
2.Pre c autio ns
• Exposure to a spotlight or an object emitting strong light may cause smear or blooming.
• Ensure that the power source complies with normal specications before supplying it
to the camera.
NOTE
6 7
Do not operate under extreme temperature conditions.
Using the camera in temperatures exceeding 50˚C or below -10˚C may
lower image quality or cause the camera to malfunction.
Do not operate in high humidity environments.
Using the camera in places with high humidity may lessen picture quality because of moisture on the lens.
Do not operate under unsteady lighting.
The camera will not work properly in places with great changes in
illumination intensity, such as uorescent lamps.
Do not attempt to disassemble the camera.
Do not drop the camera or subject it to physical shock.
It may damage the camera if dropped or subjected to strong impact.
Do not exposed to an intense light source such as direct sunlight
It may damage the CCD.
Do not exposed the camera to rain or other types of liquids.
It may damage the camera.
Do not exposed the camera to radioactivity.
It may damage the CCD.
1/4” Sony Double Scan Exview HAD CCD
1/4” Sony Double Scan EXview HAD CCD with 380,000(NTSC) or
440,000(PAL) effective pixels, delivers an excellent signal-to-noise ratio, exceptional low-light performance, enhanced FOV, and high image quality. The minimum illumination required is 0.1 Lux(Night Mode, DSS OFF)
36x Optical Zoom
The Built-in 36x Optical zoom lens is a highly durable component. It features Auto Focus, Auto Iris and Zoom functions.
SS-3 DSP Chip
SS-3 features a powerful SONY's DSP that can efciently remove image
noise, producing crisp and clear images even under low lighting conditions.
High Resolution
Featuring 550TV lines horizontal resolution in color mode and 570TV lines horizontal resolution in BW mode.
Day & Night
The camera automatically determines whether it is night time or day time, selecting operating mode automatically. The camera operates in color mode during day light conditions and BW mode in night conditions for clearer
identication.
Privacy Masking
Privacy Zone masking protects private objects and areas. The camera sets up to 15 places per screen simultaneously.
Multi-Protocol
Adopts various communications protocol, such as VISCA(SONY), LG, Pelco­ D/P compatible. It enables the camera to be compatible with other equipment.
3.Fea t ures
FEATURES
2
CAUTIONS
1
4.
Components and Acc essor i es
Package
8 9
Operation Manual 36x Zoom Camera
Operation
Manual
Tripod Mounting
Tripod Mounting bracket is assembled to the top and buttom of the camera.
Tripod Mounting Hole
Install the camera on an optional tripod. The tripod must be equipped with screws with
specications shown on the right.
5.
Dimensions
6.
Overv i ew
10 11
Key Buttons
• Following buttons control zoom, focus, and auto focus functions. W(WIDE) button : To widen the view. (ZOOM OUT) T(TELE) button : To close in on a far object. (ZOOM IN) N(NEAR) button : To see a near object clearly. F(FAR) button : To see a far object clearly.
• Pressing the M(MENU) button prompts the main setup menu.
• Setup menu can be navigated using these buttons. MENU(M) button : To access the main setup menu. UP(T) button : To move the arrow indicator to up. DOWN(W) button : To move the arrow indicator to down. LEFT(N) button : To change date to down. RIGHT(F) button : To change date to up.
Control Interface
• Used to connect the remote control equipment. Includes the RS-485 communication pin. Zoom and focus functions can be controlled by using external signals.
Power LED
• Illuminates when power is supplied.
Video Output Jack
• Used to connect an external video monitor in jack.
Power Input Terminal
• Power supply terminal(DC12V± 10%)
Vid e o O u t J a c k
Pow e r L E D
Pow e r I n pu t
Ter m i n a l
Con t r o l Int e r f a c e
Key B u t t on s
Rear View
7.Ins t allat ion
Connecting to Monitor
• Connect Video Out Jack to the monitor's Video In Jack as shown below.
• Connection methods may vary depending on the video equipment. Please refer to
the model specic instruction manual.
• Connect cables with the unit powered down.
Set the 75Ω / Hi - Z selection switch as shown below if you have an intermediate
device.
CAMERA
INTERMEDIATE END MONITOR
VIDEO VIDEO
7.Ins t allat ion
• Connect the power once the installation is complete.
• When connecting to the power source, make sure the polarity of the power adapter
is correct.
• Use a DC12V/500mA power source for the camera.
NOTE
Connecting to Power
Connect the power cable to the camera's power in as shown in the gure below
• As the voltage drop according to the length of the cable in the above table, a camera may malfunction if there is an excessively long cable run.
• Voltage drops in the above table are variable according to types of cable manufacturer.
Resistance of copper wire [at 20℃ (68˚F)]
Copper wire size
(AWG)
#24
(0.22㎟)
#22
(0.33㎟)
#20
(0.52㎟)
#18
(0.83㎟)
Resistance(Ω/m) 0.078 0.050 0.030 0.018
Voltage Drop(V/m) 0.028 0.018 0.011 0.006
12 13
7.Ins t allat ion
Control Interfaces(Communication Control Connector)
The camera can be controlled by using external controllers like as the keyboard controller.(RS-485 Communication)
Connecting PC or DVR (Serial Port)
Connecting to RS-485 Controller
RS-232C TO RS-485 CONVERTER
7.Ins t allat ion
Connecting to External Controller
FUNC. FOCUS ZOOM
TELE COM +6V
WIDE COM -6V
NEAR +6V COM
FAR -6V COM
MENU +6V +6V
STOP COM COM
Co n tro l ler Fun c tio n Tab l e
14 15
7.Ins t allat ion
External D&N Input / Output
• It can be switched to DAY mode or NIGHT mode by receiving the signal from external light sensor or IR LED LAMP. when D&N Mode is set " EXTERNAL" on the OSD menu of the Camera.
• It can be sent signal to other equipment like as IR LED lamp. In this case, IR LED lamp can turn on using this signal.
J705
①
Day/Night EXT
②
GND
J706
①
Day/Night Out
②
GND
• This feature is available while using without case model.
High(+5V) : NIGHT
LOW(GND) : DAY
High(+3.3V) : IR LED ON(NIGHT)
LOW(GND) : IR LED OFF(DAY)
8.Ope r ating Came r a
SETUP
1.LENS [
┛
]
2.EXPOSURE [
┛
]
3.WHITE BALANCE [┛]
4.WDR/BLC [
┛
]
5.DAY&NIGHT [
┛
]
6.IMAGE [
┛
]
7.SPECIAL [
┛
]
8.FACTORY DEFAULT
9.EXIT
LENS
FOCUS MODE
...
AUTO
FOCUS LIMIT
...
50CM
ZOOM START
...
x1
ZOOM STOP
...
x360
ZOOM SPEED
...
15
E-ZOOM
...
ON INITIAL RETURN
EXPOSURE
AE MODE
...
SHUT FIX
BRIGHTNESS
...
8
FLICKERLESS
...
OFF
SHUTTER
...
1/60
AGC LEVEL
...
AUTO
MAX AGC GAIN
...
29dB
MAX FIELDS
...
128 INITIAL RETURN
WHITE BALANCE
WB MODE
...
MANUAL WB CONTROL
...
-
RED CONT
...
30 BLUE CONT
...
50 INITIAL RETURN
OSD Menu Conguration
16 17
WDR/BLC
WDR MODE
...
ON
WDR LEVEL
...
08
BLC MODE
...
OFF
BLC ZONE
...
CENTER
BLC LEVEL
...
04 INITIAL RETURN
DAY & NIGHT
D&N MODE
...
AUTO
DETECT MODE
...
SENSOR
DWELL TIME
...
5 SEC
D->N LEVEL
...
8 LUX
N->D LEVEL
...
100 LUX
BURST(NIGHT)
...
OFF
INITIAL RETURN
IMAGE
ROTATE
...
NORMAL
FREEZE
...
OFF
SHARPNESS
...
10
NEGATIVE
...
OFF INITIAL RETURN
SPECIAL
CAM ID
...
001 LANGUAGE
...
ENG BAUDRATE
...
9600 TITLE
...
[┛] PRIVAC
...
[┛] DISPLAY
...
[┛] MOTION DETECT
...
[┛] INITIAL RETURN
TITLE
↓ __________ [M]select ABCDEFGHIJKLMNOPQRSTUVWXYZ abcdef g h i j k l m n o p q r s t u v w x y z 0123456789ДЦЬИЖдцьбйнсуъЯж SPACE
>> <<BACK MORE>>
LOCATION
...
[┛]
RETURN
PRIVACY
ZONE NUM.
...
3
CONTROL
...
MASK
H START
...
10
V START
...
30
H WIDTH
...
200
V HEIGHT
...
110
COLOR
...
BLACK INITIAL RETURN
DISPLAY
CAM ID
...
ON
CAM TITLE
...
ON
CAM STATE
...
ON
ZOOM RATIO
...
ON
MOTION DETECT
...
OFF
POWER ON MSG.
...
ON
STANDBY
...
ON
INITIAL RETURN
MOTION DETECT
ZONE NAME
...
WINDOW0 CONTROL
...
ON H START
...
4 V START
...
2 H WIDTH
...
4 V HEIGHT
...
4 SENSITIVITY
...
8 ALARM
...
OSD&COM INITIAL RETURN
[TITLE LOCATION] [M] [┛]
CAM TITLE
[T]↑ [W]↓ [N]←[F]
→
8.Ope r ating Came r a
Without WDR Model
BLC
BLC MODE
...
OFF
BLC ZONE
...
CENTER
BLC LEVEL
...
04 INITIAL RETURN
8.Ope r ating Came r a
On Screen Display
18 19
NO Function Format Description
①
Focus
ND
Focus Auto Mode
Focus Manual Mode or Focus Push Mode
A •
In case of Focus Push Mode, while pushing the Pocus push Auto Key, focus operates as mode temporary
②
Rotate
ND
Normal Image
Horizontal Rotate
Vertical Rotate
Horizontal&Vertical(180°) Rotate
③
Backlight / WDR
ND
Backlight OFF & WDR OFF
Backlight ON & WDR OFF
WDR
Backlight OFF & WDR ON
CAMER A S TA TE
36x
Dx360
CAUTION : The WDR is an Option function
④
WB
ND
Factory default
ATW
Auto Trace WB Mode
PwB
Push Auto Mode
IwB
Indoor WB Mode
OwB
Outdoor WB Mode
MwB
Manual WB Mode
AwB
Wide Range Trace Mode
⑤
Shutter Speed
ND
Normal Shutter (Automatic Shutter)
1/1 ~ 1/ 100000
Manual Shutter High Shutter 1/50(60) ~1/100000 Slow Shutter 1/1 ~ 1/25(30)
Flicker Free Mode (1/120(100))
⑥
Freeze
ND
Normal (live) Image
Still Image
⑦
Night shot
ND
Day State (ICR OFF)
Night Shot State
(Removed the IR cut lter, ICR ON)
⑧
Motion Detect Message
ND
Normal Image
Motion is detected
⑨
Title
*********
Title (Max. 10 characters), This position is adjustable (default : Left bottom side)
⑩
Zoom Ratio x1~Dx360
Optical(x1 ~ x36), Digital(Dx36~Dx360)
⑪
Camera ID
ID:000 ~ ID:255
Camera Identication Number
⑫
Standby STANDBY
Stand-by Mode
⑬
Po we r On Msg
-
Informs the camera system settings. It is displayed for 2 seconds after power on.
CAMER A S TA TE
8.Ope r ating Came r a
8.Ope r ating Came r a
Menu Setup
Use the ve buttons on back of the camera.
1. Press the MENU button to access the main setup mode.
• Main setup menu is displayed on the monitor screen.
• The Menu consists of the "Main-Menu" and "Sub-Menu"
2. Select the desired feature using the TELE and WIDE button.
• Each pressing of the TELE or WIDE button moves the indicator to the next or previous feature.
SETUP
1.LENS [┛]
2.EXPOSURE [┛]
3.WHITE BALANCE [┛]
4.WDR/BLC [┛]
5.DAY&NIGH [┛]
6.IMAGE [┛]
7.SPECIAL [┛]
8.FACTORY DEFAULT
9.EXIT
NEAR/FAR
TELE/WIDE
20 21
Fu n c ti on
Se t u p Ke y
TEL E ( U P ) B U T T ON
FAR ( R I G H T) B U TT O N
MEN U B U T TO N
WID E ( D O W N) B U TT O N
NEA R ( L E F T) B U TT O N
8.Ope r ating Came r a
3. Select the desired feature using the TELE and WIDE button.
• The indicator moves up and down in the main menu feature.
• Move the arrow indicator to the desired feature.
4. Change the status of the selected feature using the NEAR and FAR button
• Pressing the NEAR/FAR button, the sub-menu is displayed.
• Press the TELE/WIDE button to move up and down the sub-menu. category and set each category by pressing the NEAR/FAR button.
• When completed, move the arrow indicator to "RETURN" and press the NEAR/FAR button.
5. Press the MENU button at the main-menu or sub-menu screen to hide the menu.
• It does not apply when the MENU button is used for other uses.
SETUP
1.LENS [┛]
2.EXPOSURE [┛]
3.WHITE BALANCE [┛]
4.WDR/BLC [┛]
5.DAY&NIGH [┛]
6.IMAGE [┛]
7.SPECIAL [┛]
8.FACTORY DEFAULT
9.EXIT
LENS
FOCUS MODE … AUTO FOCUS LIMIT … 50CM ZOOM START … X1 ZOOM STOP … X360 ZOOM SPEED … V-FAST E-ZOOM … ON INITIAL
RETURN
6. FACTORY DEFAULT
• All menu will be initialized except for the Camera ID
8.Ope r ating Came r a
Sub-Menu : LENS
1. FOCUS MODE
• AUTO : Focus is automatically adjusted with moving zoom.
• MANUAL : Focus can be manually adjusted, independent of moving zoom.
LENS
FOCUS MODE … AUTO FOCUS LIMIT … 50CM ZOOM START … X1 ZOOM STOP … X360 ZOOM SPEED … V-FAST E-ZOOM … ON INITIAL RETURN
22 23
2. FOCUS LIMIT
• Minimum distance the camera can focus. ex) 50 cm: Subjects closer than 50 cm cannot be brought into focus.
• 1CM/10CM/50CM/1.5M/2M/3M/5M/10M/INF
3. ZOOM START
• Congure zoom start ratio.
• Can be set from x1 to x36.
4. ZOOM STOP
• Congure zoom stop ratio.
• Can be set from x1 to x360.
8.Ope r ating Came r a
5. ZOOM SPEED
• Congure zoom tracing speed.
• V-FAST(4.2sec)/ FAST(4.6sec)/ NORMAL(5.0sec)/SLOW(7.5sec)
6. E-ZOOM
• Congure digital zoom function.
• ON : Enable Digital Zoom
• OFF : Disable Digital Zoom
7. INITIAL
• Initializes the changed category in LENS menu.
• Press the NEAR/FAR button to conrm.
8.Ope r ating Came r a
Sub-Menu : EXPOSURE
1. AE MODE
• AUTO : Automatic mode. Exposure is controlled by Shutter, Iris & Gain.
• SHUT FIX : Shutter priority mode. Exposure is controlled by Iris & Gain.
• AGC FIX : Gain priority mode. Exposure is controlled by Shutter & Iris.
• MANUAL : Manual mode.
2. BRIGHTNESS
• Use this function to adjust image brightness.
• Can be adjusted from 0(dark) to 15 (Bright).
3. FLICKERLESS
• Flicker correction mode.
• -(WDR) : Now WDR ON State
4. SHUTTER
• Can be changed while in MANUAL and SHUT FIX mode.
• Shutter speed can be changed from 1/1 to 1/100,000s.
• Standard shutter speed : NTSC - 1/60. PAL - 1/ 50.
• -(WDR) : Now WDR ON State
EXPOSURE
AE MODE … SHUT FIX BRIGHTNESS … 8 FLICKERLESS … OFF SHUTTER … 1/60 AGC LEVEL … ­MAX AGC GAIN … MID MAX FIELDS … 128 INITIAL RETURN
24 25
8.Ope r ating Came r a
5. AGC LEVEL
• For brighter images, set to the desired value.
• Can be changed from OFF to 36dB while in AGC FIX and MANUAL mode.
6. AGC LEVEL
• Adjusts the maximum gain mode.
• OFF, LOW, MID, HIGH, SUPER
7. MAX FIELDS
• Adjusts the maximum accumulation elds.
• Can be changed from OFF to 128FLD.
8. INITIAL
• Initializes the changed category in EXPOSURE menu.
• Press the NEAR/FAR button to conrm.
Co nt rol t ab le wi th A E mod e
Auto Shutter Fix AGC Fix Manual
BRIGHTNESS O O O X
FLICKERLESS(*2) O O O O
SHUTTER(*2) X O X O
AGC LEVEL X X O O
AGC MAX GAIN O O(*1) O X
MAX FIELD O X O X
(*1)
The AGC MAX GAIN will be write-protected if the shutter is slow shutter mode.
(*2) If WDR is ON, the ickerless and Shutter are write-protected
8.Ope r ating Came r a
Sub-Menu : WHITE BALANCE
• ATW : When color temperature is 2400° K~10000 K°, select this mode.
• INDOOR : Set color temperature to be 3200°K.
• OUTDOOR : Set color temperature to be 5800°K.
• PUSH : Color will be automatically adjusted while the MENU button is pressed in the temporary automatic mode.
• MANUAL : Can increase or decrease the red or blue value while monitoring the difference on the screen.
• AWB : The white balance is automatically adjusted in a specic environment.
1. WB MODE
• Indicates the condition of each WB mode.
• ' - ' no operation
2. WB CONTROL
• Can be changed in MANUAL mode only.
• Can be set from 0 to 255.
3. RED CONT
• Can be changed in MANUAL mode only.
• Can be set from 0 to 255.
4. BLUE CONT
• Initializes the changed category in WHITE BALANCE menu.
• Press the NEAR/FAR button to conrm.
5. INITIAL
WHITE BALANCE
WB MODE … MANUAL WB CONTROL … ­RED CONT … 30 BLUE CONT … 50 INITIAL RETURN
26 27
8.Ope r ating Came r a
Sub-Menu : WDR/ BLC
WDR/BLC
WDR MODE … ON WDR LEVEL … 8 BLC MODE … OFF BLC ZONE … CENTER BLC LEVEL … 4 INITIAL RETURN
• Initializes the changed category in WDR/BLC menu.
• Press the NEAR/FAR button to conrm.
1. WDR MODE(*)
• OFF : Disable the Wide Dynamic Range function
• ON : WDR Fixed mode.
• Can adjust the level(0~15)
2. WDR LEVEL(*)
• Compensates for scenes with "BACKLIGHT"conditions.
3. BLC MODE
• Sets backlight compensation weighting zone(BLC ON mode).
• Can be selected CENTER, TOP, BOTTOM, LEFT, RIGHT.
4. BLC ZONE
• Sets backlight compensation weighting value(BLC ON mode).
• Can be adjusted from 0 to 15.
5. BLC LEVEL
6. INITIAL
• The BLC dose Not Work in WDR ON mode
• (*)The WDR is an Option function
NOTE
BLC
BLC MODE … OFF BLC ZONE … CENTER BLC LEVEL … 4 INITIAL RETURN
Wit h o u t WD R M od e l
8.Ope r ating Came r a
Sub-Menu : DAY & NIGHT
• Select desired operation mode.
• COLOR : Day x mode.
• BW : Night x mode.
• AUTO : Automatically changes COLOR/BW mode according to illuminance.
• EXTERNAL : Changes COLOR/BW mode according to external input signal. B/W(HIGH, +5V) COLOR(LOW, GND)
1. D&N MODE
• SENSOR : Detect lighting conditions by photo-sensor.
• VIDEO : Detect lighting conditions by video level.
• AUTO : Automatically detect lighting conditions by photo-sensor & video level.
2. DETECT MODE
• Sets conversion time of IR cut lter while in automatic mode.
• Can be adjusted from 0 sec to 10 sec.
3. DWELL TIME
• Sets turnover level from COLOR to BW while in AUTO Mode.
• Can be adjusted from 1 Lux to 90 Lux.
• It can be adjusted under sets SENSOR mode.
4. D→N LEVEL
Sets up the level higher while installing into the outdoor housing.
DAY & NIGHT
D&N MODE … AUTO DETECT MODE … SENSOR DWELL TIME … 1 SEC D→N LEVEL … 1 Lux N→D LEVEL … 10 Lux BURST(NIGHT) … ON INITIAL RETURN
Sets up the level higher while installing into the outdoor housing.
28 29
8.Ope r ating Came r a
• Sets turnover level from BW to COLOR while in AUTO Mode.
• Can be adjusted from 3 Lux to 100 Lux.
• It can be adjusted under sets SENSOR mode.
5. N→D LEVEL
• Select the burst signal ON/OFF when NIGHT(ICR ON) mode.
6. BURST(NIGHT)
• Initializes the changed category in DAY & NIGHT menu.
• Press the NEAR/FAR button to conrm.
7. INITIAL
8.Ope r ating Came r a
Sub-Menu : IMAGE
• NORMAL : Normal image.
• H : Use this feature to horizontally inverse the screen.
• V : Use this feature to vertically inverse the screen.
• H/V : Use this feature to horizontally & vertically inverse the screen.
1. ROTATE
• Use this feature to freeze capture an image.
2. FREEZE
• Increasing this value sharpens object edges. Too high of a setting, produces noise and may obscure the image.
• Can be adjusted from 0(blunt image) to 15(sharp image).
3. SHARPNESS
• Select enables or disables negative image feature.
• Positive image is a normal image.
4. NEGATIVE
• Initializes the changed category in IMAGE menu.
• Press the NEAR/FAR button to conrm.
5. INITIAL
IMAGE
ROTATE … NORMAL FREEZE … OFF SHARPNESS … 10 NEGATIVE … OFF INITIAL RETURN
30 31
8.Ope r ating Came r a
Sub-Menu : SPECIAL
• Assign an identication number to the camera (0 to 255).
1. CAM ID
• Displays language can be selected from ENG/CHI/RUS/SPN/GER.
• Language for OSD(English, Chinese, Russian, Spanish, German)
2. LANGUAGE
• Congure baud rate from 2400/4800/9600/19200/38400 bps.
• Serial communication speed (bps)
3. BAUDRATE
• Use this feature to designate a name for the camera, which will display on the monitor screen.
4. TITLE
• Use this feature to mask privacy area, which will display on the monitor screen.
5. PRIVACY
• Use this feature to display the Function-OSD on the screen.
6. DISPLAY
• Use this feature to alert signal upon detecting motion.
7. MOTION DETECT
• Initializes the changed category in SPECIAL menu.
• Press the NEAR/FAR button to conrm.
• The CAM ID does not initialized.
8. INITIAL
SPECIAL
CAM ID … 001 LANGUAGE … ENG BAUDRATE … 9600 TITLE … [┛] PRIVACY … [┛] DISPLAY … [┛] MOTION DETECT … [┛] INITIAL RETURN
8.Ope r ating Came r a
SPECIAL Sub-Menu : TITLE
1. Move the cursor to the character entry eld using the NEAR or FAR
button.
2. Use TELE, WIDE, NEAR, and FAR buttons to select a desired character.
3. Press the MENU button to conrm selection of the blinking character. Then the character is saved, and the cursor in the entry eld moves to
the next position.
4. You can choose up to 156 characters from the table.
TITLE
↓ CAM TITLE [M] select
-----------
ABCDEFGHIJKLMNOPQRSTUVWXYZ a b c d e f g h i j k l m n o p q r s t u v w x y z 0123 4 5 6 7 89 Ä Ö Ü ÈÆ ä ö ü áé í ñ ó úß æ SPACE>> <<BACK MORE>>
LOCATION … [┛] RETURN
Entry Field
Max.10 Character
ABCDEFGHIJKLMNOPQRSTUVWXYZ a bc de f gh i j k lm n op qr s tu v w x yz 0123456789ДЦЬИЖдцьбйнсуъЯж SPACE>> <<BACK MORE>>
АБВГДЕЁЖЗИЙКЛМНОПРСТУФХЦЧШ ЩЪЫЬЭЮЯⓞ①②③④⑤⑥⑦⑧⑨■△▽▷◁▶◀▲▼ %#&/!?[ ] ()<> ↕ ↑↓→← ☞ *,.; : ‘“• SPACE>> <<BACK MORE>>
↕
[M]
Symbols
↓
Selected position in the entry
eld
"A"~“æ” Normal character
SPACE>> Insert space " "character
<<BACK
Selected position moves to left
in the entry eld
MORE>> Displays another characters.
32 33
8.Ope r ating Came r a
5. You can select on screen position of the TITLE.
• Move the cursor to "LOCATION" and press NEAR/FAR button.
• The TITLE is displayed on the top-left of the monitor screen.
• Select the position using the TELE/WIDE/NEAR/FAR button.
• Press the MENU button to conrm the position and exit this menu.
6. When completed, move the cursor to "RETURN" and press NEAR/FAR button.
[TITLE LOCATION] [M] ┛
CAM TITLE
[T]↑[W]↓[N]←[F]→
8.Ope r ating Came r a
SPECIAL Sub-Menu : PRIVACY
1. ZONE NO
• Select the privacy mask zone number(1 ~ 15).
2. CONTROL
• Select desired masking effect.
• OFF: disable privacy zone as mask or mosaic.
• MASK: enable privacy zone as mask.
• MOSAIC : enable privacy zone as mosaic.
3. H START
• Set the horizontal starting point of privacy zone(0 ~ 180).
4. V START
• Set the vertical starting point of privacy zone(0 ~ 140).
5. H WIDTH
• Set the width of privacy zone(0 ~ 220).
6. V HEIGHT
• Set the height of privacy zone(0 ~ 180).
7. MASK COLOR
• Congure desired mask color(not mosaic).
• Up to eight different colors are supported. BLACK/BLUE/RED/GREEN/YELLOW/GRAY1/GRAY2/WHITE
8. INITIAL
• Initializes the changed category in PRIVACY menu.
• Press the NEAR/FAR button to conrm.
PRIVACY
ZONE NO … 3 CONTROL … MASK H START … 10 V START … 30 H WIDTH … 200 V HEIGHT … 110 MASK COLOR … BLACK INITIAL RETURN
34 35
8.Ope r ating Came r a
SPECIAL Sub-Menu : DISPLAY
1. CAM ID : Displays camera ID on ⑪ of the screen.
2. CAM TITLE : Displays camera title on ⑨ of the screen.
3. CAM STATE : Displays camera state on
① ~ ⑦
of the screen.
4. ZOOM RATIO : Displays zoom ratio on ⑩ of the screen.
5. MOTION MSG( MD ) : Displays MD character on ⑧ of the screen, when
the motion is detected.
6. STANDBY : Displays system waiting message on ⑫ of the screen, when power on.
7. POWER ON MSG : Displays system information on ⑬ of the screen, when power on.
8. INITIAL
• Initializes the changed category in SPECIAL menu.
• Press the NEAR/FAR button to conrm.
Use this feature to display the Function-OSD on the screen.
DISPLAY
CAM ID … ON CAM TITLE … ON CAM STATE … ON ZOOM RATIO … ON MOTION MSG( MD ) … ON POWER ON MSG … OFF STANDBY … ON INITIAL RETURN
36x
Dx360
8.Ope r ating Came r a
SPECIAL Sub-Menu : MOTION DETECT
1. ZONE NAME
• Select the motion detection area number.
• Use the mask displayed on the screen to set positions.
• Can be selected WINDOW0~3 or BLOCK.
2. CONTROL
• Select enables or disables the motion detection feature.
3. H START
• Set the horizontal starting point for motion detection area.
• Select desired position from 11 to 178 in WINDOW0~3.
• Select desired position from 0 to 11 in BLOCK.
4. H END
• Set the horizontal terminating point for motion detection area.
• Select desired position from 11 to 178 in WINDOW0~3.
• Select desired position from 0 to 11 in BLOCK.
5. V START
• Set the vertical starting point for motion detection area.
• Select desired position from 6 to 128 in WINDOW0~3.
• Select desired position from 0 to 7 in BLOCK.
When there is a movement in the monitoring area, there will be an alarm, or the user will be informed through communications or " MD " will display on the screen.
MOTION DETECT
ZONE NAME … WINDOW0 CONTROL … ON H START … 16 H END … 88 V START … 9 V END … 65 SENSITIVITY … 8 ALARM … OSD&SERIAL INITIAL RETURN
36 37
8.Ope r ating Came r a
6. V END
• Set the vertical starting point for motion detection area.
• Select desired position from 6 to 128 in WINDOW0~3.
• Select desired position from 0 to 7 in BLOCK.
7. SENSITIVITY
• Increase or decrease detection sensitivity value.
• Can be set from 1 (low response) to 15 (sensitive).
8. ALARM
• Select desired alert type.
• OSD : The WINDOW or BLOCK will be displayed on the screen when motion is detected.
• SERIAL : Alert packet is transmitted via RS-485 when motion is detected.
• OSD&SERIAL : Use OSD and SERIAL feature simultaneously.
9. INITIAL
• Initializes the changed category in MOTION DETECT menu.
• Press the NEAR/FAR button to conrm.
9.Com m unica tion P rotoc ol
Pelco"D" Compatable Protocol Commands
Most widely used Commands
38 39
9.Com m unica tion P rotoc ol
Default Protocol Commands
Most widely used Commands
• The camera can be controlled by VISCA(SONY), LG, Pelco-P Compatable Protocol.
For more detailed informations refer to their manuals.
NOTE
10.Sp e cific ation s
Model WDR (Wide Dynanic Range) High RES. Zoom
Signal S ystem NTSC PAL
CCD
Image Sensor 1/4” Sony Double Scan Exview HAD CCD
Total Pixels 811(H) x 508(V) 795(H) x 596(V)
Effective Pixels 768(H) x 494(V) 752(H) x 582(V)
Optics
Lens 36x, f=3.4~122.4mm(F1.6 ~F4.5)
Min. Object Distance 0.01m(W) ~ 1.5m(T)
Digital Zoom 1x ~ 10x
Angle Field of View Horizontal : 57.8 degrees(Wide) to 1.7 degrees(Tele)
Sync.
Scanning System 2:1 Interlace
Sync. System Internal/Line-lock
Frequency H:15.734 KHz V:59.94 Hz H:15.625KHz V:50 Hz
Electric al
Horizontal Resolution 550 TV Lines
Camera Title Off/On(Displayed 10 characters)
Camera ID 256 ID Selectable
Video Output 1.0Vp-p/75Ω
S/N Ratio More than 50dB (AGC Off, DSS Off)
Min. Illumination 0.3 Lux : Color, 0.1Lux : BW (30 IRE @ Wide End, AGC Super, DSS Off)
Backlight Compensation Off/On (Level Adjustable, Area Selectable)
WDR Off / On (Level Adjustable)
Mechanical D&N AUTO / COLOR / B/W / EXTERNAL
Gain Control Off / Low / Mid / High / Super
White Balance
ATW / INDOOR / OUTDOOR / PUSH AUTO /
MANUAL(R Gain, B Gain) / AWB
Electronic Shutter 1/60 ~ 1/100,000 sec 1/50 ~ 1/100,000 sec
Digital Slow Shutter Off, 2 ~ 128 Field
Flickerless Off / On
Motion Detection 5 Zones
OSD English / Chinese / Russian / Spanish / German
Focus Auto / Manual
Zoom Tracking Speed 4.2 Sec : Wide to Tele
Lens Initialize Support
Zoom/Focus Preset 512 internal / 128 external
Privacy Function 15 Zones
E-Flip Off, Horizontal, Vertical, Horizontal / Vertical
Freeze Off / On
Communic ation
Serial Control
RS-485(2400bps, 4800bps, 9600bps, 19200bps, 38400bps Selectable)
KT&C, PELCO-D/P, VISCA, LG compatible
Voltage Control External Control by Voltage (ZOOM, FOCUS)
Power
Input Voltage DC 12V(±10%)
Input Current Max. 350mA
Operatin g Temperature /Humidity -10°C to +50°C
Dimensio n 67mm X 73mm X 119.5mm
Weight Approx. 502g
40
10.Sp e cific ation s
Model High RES. Zoom
Signal S ystem NTSC PAL
CCD
Image Sensor 1/4” Sony Super HAD CCD
Ⅱ
Total Pixels 811(H) x 508(V) 795(H) x 596(V)
Effective Pixels 768(H) x 494(V) 752(H) x 582(V)
Optics
Lens 36x, f=3.4~122.4mm(F1.6 ~F4.5)
Min. Object Distance 0.01m(W) ~ 1.5m(T)
Digital Zoom 1x ~ 10x
Angle Field of View Horizontal : 57.8 degrees(Wide) to 1.7 degrees(Tele)
Sync.
Scanning System 2:1 Interlace
Sync. System Internal/Line-lock
Frequency H:15.734 KHz V:59.94 Hz H:15.625KHz V:50 Hz
Electric al
Horizontal Resolution 550 TV Lines
Camera Title Off/On(Displayed 10 characters)
Camera ID 256 ID Selectable
Video Output 1.0Vp-p/75Ω
S/N Ratio More than 50dB (AGC Off, DSS Off)
Min. Illumination 0.1 Lux : Color, 0.06Lux : BW (30 IRE @ Wide End, AGC Super, DSS Off)
Backlight Compensation Off/On (Level Adjustable, Area Selectable)
Mechanical D&N AUTO / COLOR / B/W / EXTERNAL
Gain Control Off / Low / Mid / High / Super
White Balance
ATW / INDOOR / OUTDOOR / PUSH AUTO /
MANUAL(R Gain, B Gain) / AWB
Electronic Shutter 1/60 ~ 1/100,000 sec 1/50 ~ 1/100,000 sec
Digital Slow Shutter Off, 2 ~ 128 Field
Flickerless Off / On
Motion Detection 5 Zones
OSD English / Chinese / Russian / Spanish / German
Focus Auto / Manual
Zoom Tracking Speed 4.2 Sec : Wide to Tele
Lens Initialize Support
Zoom/Focus Preset 512 internal / 128 external
Privacy Function 15 Zones
E-Flip Off, Horizontal, Vertical, Horizontal / Vertical
Freeze Off / On
Communic ation
Serial Control
RS-485(2400bps, 4800bps, 9600bps, 19200bps, 38400bps Selectable)
KT&C, PELCO-D/P, VISCA, LG compatible
Voltage Control External Control by Voltage (ZOOM, FOCUS)
Power
Input Voltage DC 12V(±10%)
Input Current Max. 300mA
Operatin g Temperature /Humidity -10°C to +50°C
Dimensio n 67mm X 73mm X 119.5mm
Weight Approx. 502g
41
Loading...
Buy Points How it Works FAQ Contact Us Questions and Suggestions Privacy Policy Cookie Policy Terms of Use