Drg No. KSRFRD374-IS-A
11.05.2018MAC
Installation Sheet
Important Information
It is recommended that luminaires are installed by a qualified electrician ensuring the installation
complies to current IEE wiring regulations & local building control.
These products are designed for connection to a 230-240V mains supply.
Any broken or damaged parts should be replaced as soon as possible.
KSR will not accept responsibility for any claims arising from a poor installation.
Important User Advice
Always switch off mains supply before servicing.
This luminaire is suitable for indoor use only and should not be fitted
to damp or wet surfaces such as freshly plastered or painted ceilings.
Installation Procedure
KSR recommends that a sample hole is cut in some scrap material to familiarise yourself with
the installation. Once you are completely satisfied:
Locate the area's suitable to install these luminaires.
Cut a 70-72mm round hole in the ceiling and ensure sufficient ceiling void without
infringing on joists, water pipes or electrical cables.
Connect the mains supply to the connector block (Blue - Neutral, Yellow/Green - Earth and
Brown - Live). The terminal allows mains loop in/loop out connections, if not looping through
either of the L,E & N inputs can be used. Install the terminal cover/strain relief by pushing down
until it grips the outer cable insulation..
Select the preferred colour temperature by sliding the selector switch to either WW - Warm
White, NW - Neutral White or CW - Cool White. This must be done before the power is switched
on to the luminaire, changing the CCT while the fitting is illuminated may damage the LED COB.
Press springs back and place luminaire body into aperture.
If you are installing one of the KSR detachable rims remove the standard white rim by pulling
the trim off of the main fitting, do not twist the trim. Attach new trim by pushing and snapping it
into place.
This downlight can be covered with mineral wool insulation.
*Please note: Depending on the amount of Qr10 fittings on a circuit you may have to upgrade
the breaker to a 'C' or 'D' type due to the way electronic LED drivers start up with higher inrush
currents compared to halogen lighting. If dimming see the recommended dimmers list over the
page or visit www.ksrlighting.com for information on the latest compatible dimmers any other
questions please call our sales office on 023 92 674343.
KSR Lighting Ltd, Unit E Hazleton Interchange, Lakesmere Road, Hampshire, PO8 9JU
Available Rim Finishes: White (supplied), Chrome, Satin Chrome,
Brass, Antique Brass, Stainless Steel & Black
KSR Lighting Aftersales: 023 92 674343
E-mail: aftersales@ksrlighting.com
IP65
240V 7W
Read these instructions before commencing installation &
retain them for future reference.
KSRFRD374
Triple CCT Switchable Downlight
i
Qr7 7W COB
Luminaire suitable for all timber joist ceiling variants
up to 90 minutes.
30, 60 and 90 Minute fire rating
Approved to:- BS476 Part 21
Building Regulations Document B2 determines the ceiling
type that is required depending on the type of building
under construction. The ceiling types are designed to
provide protection to the floor above in the case of fire for
a duration as specified by the document. Using KSR's
Fire-Rated downlights ensures that this specification is
maintained even when downlights are installed in the
ceiling.
70-72mm
85mm
100mm
ØCut outØRim Size
Void Depth
Req'd
Part "B"
BS476
Part 21
Part "E"
(Acoustics)
Part "C"
Compliant
Stops moisture &
air flow through
the luminaire
WW - 3000K 577 Lumens
NW - 4000K 652 Lumens
CW - 6000K
577 Lumens
CCT Selection Lumen Performance
WARNING:
Do not change the CCT of this downlight
with the product switched on, all changes
must be done with the power off.
Colour Temperature
Selector Switch
10mm Min
22mm
To ensure a good connection
strip back 10mm of insulation
and push the cable firmly
into the terminal block
Installer Note:
WW NW CW
3000k 4000k 6000k
Fig. I
minimum void depth
100mm
80mm
42mm
31mm
180mm
85mm
79mm
Loading...