Page 1
KRYLON® DURA-TOP® Floor Coating (Part A)
Haze Gray
Not available.
Liquid.
US/Canada: (216) 566-2917
Mexico: CHEMTREC Mexico 01-800-681-9531. Available 24 hours and 365 days per
year
SAFETY DATA SHEET
Product name
Other means of
identification
Product type
Emergency telephone
number of the company
Section 1. Identification
:
:
:
:
Manufacturer
:
Krylon Products Group
101 Prospect Avenue NW
Cleveland, OH 44115
Relevant identified uses of the substance or mixture and uses advised against
Paint or paint related material.
K05400105
K05400105
Product code
:
Product Information
Telephone Number
:
US/Canada: (800) 247-3266
Mexico: Not Available
Regulatory Information
Telephone Number
:
US/Canada: (216) 566-2902
Mexico: Not Available
Transportation Emergency
Telephone Number
:
US/Canada: (800) 424-9300
Mexico: SETIQ 01-800-00-214-00 / (52) 55-5559-1588 24 hours / 365 days a year
Section 2. Hazards identification
SKIN CORROSION/IRRITATION - Category 2
SERIOUS EYE DAMAGE/ EYE IRRITATION - Category 2A
SKIN SENSITIZATION - Category 1
CARCINOGENICITY - Category 2
TOXIC TO REPRODUCTION (Unborn child) - Category 1
TOXIC TO REPRODUCTION (Fertility) - Category 2
SPECIFIC TARGET ORGAN TOXICITY (REPEATED EXPOSURE) - Category 2
Classification of the
substance or mixture
:
Signal word
:
Danger
Hazard pictograms
:
GHS label elements
Percentage of the mixture consisting of ingredient(s) of unknown oral toxicity: 57.9%
Percentage of the mixture consisting of ingredient(s) of unknown dermal toxicity: 63.2%
Percentage of the mixture consisting of ingredient(s) of unknown inhalation toxicity: 63.
2%
OSHA/HCS status
:
This material is considered hazardous by the OSHA Hazard Communication Standard
(29 CFR 1910.1200).
Causes serious eye irritation.
Causes skin irritation.
May cause an allergic skin reaction.
May damage the unborn child.
Suspected of damaging fertility.
Suspected of causing cancer.
May cause damage to organs through prolonged or repeated exposure.
:
Hazard statements
Date of issue/Date of revision
:
10/22/2018
Date of previous issue
:
3/2/2018
Version
:61/12
K05400105
KRYLON® DURA-TOP® Floor Coating (Part A)
Haze Gray
SHW-85-NA-GHS-US
Page 2
Section 2. Hazards identification
Precautionary statements
Prevention
:
Obtain special instructions before use. Do not handle until all safety precautions have
been read and understood. Wear protective gloves. Wear eye or face protection.
Wear protective clothing. Do not breathe vapor. Wash hands thoroughly after handling.
Contaminated work clothing must not be allowed out of the workplace.
Response
:
Get medical attention if you feel unwell. IF exposed or concerned: Get medical
attention. IF ON SKIN: Wash with plenty of soap and water. Wash contaminated
clothing before reuse. If skin irritation or rash occurs: Get medical attention. IF IN
EYES: Rinse cautiously with water for several minutes. Remove contact lenses, if
present and easy to do. Continue rinsing. If eye irritation persists: Get medical attention.
Storage
:
Store locked up.
Disposal
Dispose of contents and container in accordance with all local, regional, national and
international regulations.
Hazards not otherwise
classified
:
None known.
Please refer to the SDS for additional information. Keep out of reach of children. Do not
transfer contents to other containers for storage.
Supplemental label
elements
DELAYED EFFECTS FROM LONG TERM OVEREXPOSURE. Contains solvents which
can cause permanent brain and nervous system damage. Intentional misuse by
deliberately concentrating and inhaling the contents can be harmful or fatal. WARNING:
This product contains chemicals known to the State of California to cause cancer. FOR
INDUSTRIAL USE ONLY. This product must be mixed with other components before
use. Before opening the packages, READ AND FOLLOW WARNING LABELS ON ALL
COMPONENTS.
:
Section 3. Composition/information on ingredients
Epoxy Polymer
≥25 - ≤50
25068-38-6
Barium Sulfate
≥25 - ≤50
7727-43-7
Titanium Dioxide
≤10
13463-67-7
Tetrahydrofuranol
<10
97-99-4
Phenylmethanol
<10
100-51-6
Ingredient name
CAS number
% by weight
There are no additional ingredients present which, within the current knowledge of the supplier and in the
concentrations applicable, are classified as hazardous to health and hence require reporting in this section.
Other means of
identification
:
Not available.
Substance/mixture
CAS number/other identifiers
:
Occupational exposure limits, if available, are listed in Section 8.
Mixture
Any concentration shown as a range is to protect confidentiality or is due to batch variation.
Immediately flush eyes with plenty of water, occasionally lifting the upper and lower
eyelids. Check for and remove any contact lenses. Continue to rinse for at least 10
minutes. Get medical attention.
Remove victim to fresh air and keep at rest in a position comfortable for breathing. If
not breathing, if breathing is irregular or if respiratory arrest occurs, provide artificial
respiration or oxygen by trained personnel. It may be dangerous to the person providing
aid to give mouth-to-mouth resuscitation. Get medical attention. If unconscious, place
in recovery position and get medical attention immediately. Maintain an open airway.
Loosen tight clothing such as a collar, tie, belt or waistband.
Section 4. First aid measures
Eye contact
Inhalation
:
:
Description of necessary first aid measures
Date of issue/Date of revision
:
10/22/2018
Date of previous issue
:
3/2/2018
Version
:62/12
K05400105
KRYLON® DURA-TOP® Floor Coating (Part A)
Haze Gray
SHW-85-NA-GHS-US
Page 3
Section 4. First aid measures
Wash out mouth with water. Remove dentures if any. Remove victim to fresh air and
keep at rest in a position comfortable for breathing. If material has been swallowed and
the exposed person is conscious, give small quantities of water to drink. Stop if the
exposed person feels sick as vomiting may be dangerous. Do not induce vomiting
unless directed to do so by medical personnel. If vomiting occurs, the head should be
kept low so that vomit does not enter the lungs. Get medical attention. Never give
anything by mouth to an unconscious person. If unconscious, place in recovery position
and get medical attention immediately. Maintain an open airway. Loosen tight clothing
such as a collar, tie, belt or waistband.
Wash with plenty of soap and water. Remove contaminated clothing and shoes. Wash
contaminated clothing thoroughly with water before removing it, or wear gloves.
Continue to rinse for at least 10 minutes. Get medical attention. In the event of any
complaints or symptoms, avoid further exposure. Wash clothing before reuse. Clean
shoes thoroughly before reuse.
Skin contact
Ingestion
:
:
Protection of first-aiders
:
No action shall be taken involving any personal risk or without suitable training. If it is
suspected that fumes are still present, the rescuer should wear an appropriate mask or
self-contained breathing apparatus. It may be dangerous to the person providing aid to
give mouth-to-mouth resuscitation. Wash contaminated clothing thoroughly with water
before removing it, or wear gloves.
Notes to physician
:
Treat symptomatically. Contact poison treatment specialist immediately if large
quantities have been ingested or inhaled.
Specific treatments
:
No specific treatment.
Most important symptoms/effects, acute and delayed
Inhalation
:
No known significant effects or critical hazards.
No known significant effects or critical hazards.
:
Ingestion
Skin contact
:
Causes skin irritation. May cause an allergic skin reaction.
Causes serious eye irritation.
:
Eye contact
Over-exposure signs/symptoms
Skin contact
Ingestion
Inhalation
Adverse symptoms may include the following:
reduced fetal weight
increase in fetal deaths
skeletal malformations
Adverse symptoms may include the following:
reduced fetal weight
increase in fetal deaths
skeletal malformations
Adverse symptoms may include the following:
irritation
redness
reduced fetal weight
increase in fetal deaths
skeletal malformations
:
::Eye contact
:
Adverse symptoms may include the following:
pain or irritation
watering
redness
Potential acute health effects
See toxicological information (Section 11)
Indication of immediate medical attention and special treatment needed, if necessary
Date of issue/Date of revision
:
10/22/2018
Date of previous issue
:
3/2/2018
Version
:63/12
K05400105
KRYLON® DURA-TOP® Floor Coating (Part A)
Haze Gray
SHW-85-NA-GHS-US
Page 4
Section 5. Fire-fighting measures
Promptly isolate the scene by removing all persons from the vicinity of the incident if
there is a fire. No action shall be taken involving any personal risk or without suitable
training.
Hazardous thermal
decomposition products
Specific hazards arising
from the chemical
Decomposition products may include the following materials:
carbon dioxide
carbon monoxide
sulfur oxides
halogenated compounds
metal oxide/oxides
In a fire or if heated, a pressure increase will occur and the container may burst.
Fire-fighters should wear appropriate protective equipment and self-contained breathing
apparatus (SCBA) with a full face-piece operated in positive pressure mode.
Special protective
equipment for fire-fighters
Use an extinguishing agent suitable for the surrounding fire.
Extinguishing media
:
:
:
None known.
Suitable extinguishing
media
:
Unsuitable extinguishing
media
:
Special protective actions
for fire-fighters
:
Section 6. Accidental release measures
Environmental precautions
Personal precautions, protective equipment and emergency procedures
Stop leak if without risk. Move containers from spill area. Approach release from
upwind. Prevent entry into sewers, water courses, basements or confined areas. Wash
spillages into an effluent treatment plant or proceed as follows. Contain and collect
spillage with non-combustible, absorbent material e.g. sand, earth, vermiculite or
diatomaceous earth and place in container for disposal according to local regulations
(see Section 13). Dispose of via a licensed waste disposal contractor. Contaminated
absorbent material may pose the same hazard as the spilled product. Note: see
Section 1 for emergency contact information and Section 13 for waste disposal.
:
:
No action shall be taken involving any personal risk or without suitable training.
Evacuate surrounding areas. Keep unnecessary and unprotected personnel from
entering. Do not touch or walk through spilled material. Avoid breathing vapor or mist.
Provide adequate ventilation. Wear appropriate respirator when ventilation is
inadequate. Put on appropriate personal protective equipment.
Avoid dispersal of spilled material and runoff and contact with soil, waterways, drains
and sewers. Inform the relevant authorities if the product has caused environmental
pollution (sewers, waterways, soil or air).
Large spill
:
Stop leak if without risk. Move containers from spill area. Dilute with water and mop up
if water-soluble. Alternatively, or if water-insoluble, absorb with an inert dry material and
place in an appropriate waste disposal container. Dispose of via a licensed waste
disposal contractor.
Small spill
:
Methods and materials for containment and cleaning up
For non-emergency
personnel
For emergency responders
:
If specialized clothing is required to deal with the spillage, take note of any information in
Section 8 on suitable and unsuitable materials. See also the information in "For nonemergency personnel".
Date of issue/Date of revision
:
10/22/2018
Date of previous issue
:
3/2/2018
Version
:64/12
K05400105
KRYLON® DURA-TOP® Floor Coating (Part A)
Haze Gray
SHW-85-NA-GHS-US
Page 5
Section 7. Handling and storage
Advice on general
occupational hygiene
Conditions for safe storage,
including any
incompatibilities
Eating, drinking and smoking should be prohibited in areas where this material is
handled, stored and processed. Workers should wash hands and face before eating,
drinking and smoking. Remove contaminated clothing and protective equipment before
entering eating areas. See also Section 8 for additional information on hygiene
measures.
Store in accordance with local regulations. Store in original container protected from
direct sunlight in a dry, cool and well-ventilated area, away from incompatible materials
(see Section 10) and food and drink. Store locked up. Keep container tightly closed
and sealed until ready for use. Containers that have been opened must be carefully
resealed and kept upright to prevent leakage. Do not store in unlabeled containers.
Use appropriate containment to avoid environmental contamination. See Section 10 for
incompatible materials before handling or use.
:
:
Protective measures
Put on appropriate personal protective equipment (see Section 8). Persons with a
history of skin sensitization problems should not be employed in any process in which
this product is used. Avoid exposure - obtain special instructions before use. Avoid
exposure during pregnancy. Do not handle until all safety precautions have been read
and understood. Do not get in eyes or on skin or clothing. Do not breathe vapor or mist.
Do not ingest. If during normal use the material presents a respiratory hazard, use only
with adequate ventilation or wear appropriate respirator. Keep in the original container
or an approved alternative made from a compatible material, kept tightly closed when
not in use. Empty containers retain product residue and can be hazardous. Do not
reuse container.
:
Precautions for safe handling
Epoxy Polymer
None.
Barium Sulfate
ACGIH TLV (United States, 3/2017).
TWA: 5 mg/m³ 8 hours. Form: Inhalable
fraction
NIOSH REL (United States, 10/2016).
TWA: 5 mg/m³ 10 hours. Form: Respirable
fraction
TWA: 10 mg/m³ 10 hours. Form: Total
OSHA PEL (United States, 6/2016).
TWA: 5 mg/m³ 8 hours. Form: Respirable
fraction
TWA: 15 mg/m³ 8 hours. Form: Total dust
Titanium Dioxide
ACGIH TLV (United States, 3/2017).
TWA: 10 mg/m³ 8 hours.
OSHA PEL (United States, 6/2016).
TWA: 15 mg/m³ 8 hours. Form: Total dust
Tetrahydrofuranol
AIHA WEEL (United States, 10/2011).
TWA: 0.5 ppm 8 hours.
Phenylmethanol
AIHA WEEL (United States, 10/2011).
TWA: 10 ppm 8 hours.
Section 8. Exposure controls/personal protection
Ingredient name
Exposure limits
Control parameters
Occupational exposure limits (OSHA United States)
Tetrahydrofuranol
AIHA WEEL (United States, 10/2011).
TWA: 0.5 ppm 8 hours.
benzyl alcohol
AIHA WEEL (United States, 10/2011).
TWA: 10 ppm 8 hours.
Ingredient name
Exposure limits
Occupational exposure limits (Canada)
Occupational exposure limits (Mexico)
Date of issue/Date of revision
:
10/22/2018
Date of previous issue
:
3/2/2018
Version
:65/12
K05400105
KRYLON® DURA-TOP® Floor Coating (Part A)
Haze Gray
SHW-85-NA-GHS-US
Page 6
Section 8. Exposure controls/personal protection
Hand protection
Based on the hazard and potential for exposure, select a respirator that meets the
appropriate standard or certification. Respirators must be used according to a
respiratory protection program to ensure proper fitting, training, and other important
aspects of use.
Chemical-resistant, impervious gloves complying with an approved standard should be
worn at all times when handling chemical products if a risk assessment indicates this is
necessary. Considering the parameters specified by the glove manufacturer, check
during use that the gloves are still retaining their protective properties. It should be
noted that the time to breakthrough for any glove material may be different for different
glove manufacturers. In the case of mixtures, consisting of several substances, the
protection time of the gloves cannot be accurately estimated.
Safety eyewear complying with an approved standard should be used when a risk
assessment indicates this is necessary to avoid exposure to liquid splashes, mists,
gases or dusts. If contact is possible, the following protection should be worn, unless
the assessment indicates a higher degree of protection: chemical splash goggles.
Eye/face protection
Respiratory protection
:
:
:
Body protection
Personal protective equipment for the body should be selected based on the task being
performed and the risks involved and should be approved by a specialist before
handling this product.
:
Emissions from ventilation or work process equipment should be checked to ensure
they comply with the requirements of environmental protection legislation. In some
cases, fume scrubbers, filters or engineering modifications to the process equipment
will be necessary to reduce emissions to acceptable levels.
Appropriate engineering
controls
:
If user operations generate dust, fumes, gas, vapor or mist, use process enclosures,
local exhaust ventilation or other engineering controls to keep worker exposure to
airborne contaminants below any recommended or statutory limits.
Wash hands, forearms and face thoroughly after handling chemical products, before
eating, smoking and using the lavatory and at the end of the working period.
Appropriate techniques should be used to remove potentially contaminated clothing.
Contaminated work clothing should not be allowed out of the workplace. Wash
contaminated clothing before reusing. Ensure that eyewash stations and safety
showers are close to the workstation location.
Hygiene measures
:
Individual protection measures
Skin protection
Other skin protection
:
Appropriate footwear and any additional skin protection measures should be selected
based on the task being performed and the risks involved and should be approved by a
specialist before handling this product.
Environmental exposure
controls
:
None.
Ingredient name
Exposure limits
Section 9. Physical and chemical properties
Physical state
Melting point/freezing point
Liquid.
Not available.
Not available.
Odor
pH
Not available.
Color
Evaporation rate
Not available.
Flash point
Closed cup: 252°C (485.6°F) [Pensky-Martens Closed Cup]
Not available.
Not available.
Odor threshold
:
:::::::
Appearance
Boiling point/boiling range
:
177°C (350.6°F)
Flammability (solid, gas)
:
Not available.
Date of issue/Date of revision
:
10/22/2018
Date of previous issue
:
3/2/2018
Version
:66/12
K05400105
KRYLON® DURA-TOP® Floor Coating (Part A)
Haze Gray
SHW-85-NA-GHS-US
Page 7
Section 9. Physical and chemical properties
Vapor pressure
Relative density
Vapor density
Solubility
1.52
3.5 [Air = 1]
0.02 kPa (0.15 mm Hg) [at 20°C]
Not available.
Auto-ignition temperature
Not available.
Not available.
Viscosity
Kinematic (40°C (104°F)): >0.205 cm2/s (>20.5 cSt)
Partition coefficient: noctanol/water
:
:
:
:
:::
Lower and upper explosive
(flammable) limits
:
Lower: 1.3%
Upper: 13%
Decomposition temperature
:
Not available.
Aerosol product
Molecular weight
:
Not applicable.
Section 10. Stability and reactivity
Hazardous decomposition
products
Conditions to avoid
No specific data.
Under normal conditions of storage and use, hazardous decomposition products should
not be produced.
The product is stable.
Chemical stability
No specific data.
:
:
:
Incompatible materials
:
Possibility of hazardous
reactions
:
Under normal conditions of storage and use, hazardous reactions will not occur.
Reactivity
:
No specific test data related to reactivity available for this product or its ingredients.
Section 11. Toxicological information
Acute toxicity
Tetrahydrofuranol
LD50 Oral
Rat
1600 mg/kg
-
Phenylmethanol
LD50 Dermal
Rabbit
2000 mg/kg
-
LD50 Oral
Rat
1230 mg/kg
-
Product/ingredient name
Result
Species
Dose
Exposure
Irritation/Corrosion
Epoxy Polymer
Eyes - Mild irritant
Rabbit
-
100
milligrams
-
Skin - Moderate irritant
Rabbit
-
24 hours 500
microliters
-
Skin - Severe irritant
Rabbit
-
24 hours 2
milligrams
-
Titanium Dioxide
Skin - Mild irritant
Human
-
72 hours 300
Micrograms
Intermittent
-
Tetrahydrofuranol
Eyes - Moderate irritant
Rabbit
-
24 hours 20
milligrams
-
Phenylmethanol
Skin - Mild irritant
Man
-
48 hours 16
milligrams
-
Skin - Moderate irritant
Pig-100 Percent
-
Skin - Moderate irritant
Rabbit
-
24 hours 100
-
Product/ingredient name
Result
Score
Exposure
Observation
Species
Information on toxicological effects
Date of issue/Date of revision
:
10/22/2018
Date of previous issue
:
3/2/2018
Version
:67/12
K05400105
KRYLON® DURA-TOP® Floor Coating (Part A)
Haze Gray
SHW-85-NA-GHS-US
Page 8
Section 11. Toxicological information
Carcinogenicity
Not available.
Mutagenicity
Not available.
Teratogenicity
Not available.
Reproductive toxicity
Not available.
milligrams
Sensitization
Not available.
Specific target organ toxicity (single exposure)
Specific target organ toxicity (repeated exposure)
Tetrahydrofuranol
Category 3
Not applicable.
Respiratory tract
irritation and
Narcotic effects
Phenylmethanol
Category 3
Not applicable.
Respiratory tract
irritation and
Narcotic effects
Name
Category
Name
Category
Tetrahydrofuranol
Category 2
Not determined
Not determined
Phenylmethanol
Category 2
Not determined
Not determined
Aspiration hazard
Not available.
Route of
exposure
Target organs
Route of
exposure
Target organs
Classification
Titanium Dioxide
-2B-
Product/ingredient name
NTP
IARC
OSHA
Information on the likely
routes of exposure
Inhalation
:
No known significant effects or critical hazards.
No known significant effects or critical hazards.
:
Ingestion
Skin contact
:
Causes skin irritation. May cause an allergic skin reaction.
Causes serious eye irritation.
:
Eye contact
Symptoms related to the physical, chemical and toxicological characteristics
Inhalation
Adverse symptoms may include the following:
reduced fetal weight
increase in fetal deaths
skeletal malformations
:
Eye contact
:
Adverse symptoms may include the following:
pain or irritation
watering
redness
:
Not available.
Potential acute health effects
Date of issue/Date of revision
:
10/22/2018
Date of previous issue
:
3/2/2018
Version
:68/12
K05400105
KRYLON® DURA-TOP® Floor Coating (Part A)
Haze Gray
SHW-85-NA-GHS-US
Page 9
Not available.
May cause damage to organs through prolonged or repeated exposure. Once
sensitized, a severe allergic reaction may occur when subsequently exposed to very low
levels.
General
:
Suspected of causing cancer. Risk of cancer depends on duration and level of
exposure.
Carcinogenicity
:
No known significant effects or critical hazards.
Mutagenicity
:
May damage the unborn child.
Teratogenicity
:
Developmental effects
:
No known significant effects or critical hazards.
Fertility effects
:
Suspected of damaging fertility.
Skin contact
Ingestion
Adverse symptoms may include the following:
reduced fetal weight
increase in fetal deaths
skeletal malformations
Adverse symptoms may include the following:
irritation
redness
reduced fetal weight
increase in fetal deaths
skeletal malformations
:
:
Potential chronic health effects
Delayed and immediate effects and also chronic effects from short and long term exposure
Numerical measures of toxicity
Oral
5523.9 mg/kg
Dermal
13886.8 mg/kg
Inhalation (vapors)
76.38 mg/l
Route
ATE value
Acute toxicity estimates
Potential immediate
effects
:
Not available.
Short term exposure
Potential delayed effects
:
Not available.
Potential immediate
effects
:
Not available.
Long term exposure
Potential delayed effects
:
Not available.
Section 12. Ecological information
Bioaccumulative potential
Product/ingredient name
Aquatic half-life
Photolysis
Biodegradability
Phenylmethanol
--Readily
Toxicity
Barium Sulfate
Acute EC50 634 mg/l Fresh water
Crustaceans - Cypris subglobosa
48 hours
Titanium Dioxide
Acute LC50 >1000000 µg/l Marine water
Fish - Fundulus heteroclitus
96 hours
Phenylmethanol
Acute LC50 10000 µg/l Fresh water
Fish - Lepomis macrochirus
96 hours
Product/ingredient name
Species
Result
Exposure
Persistence and degradability
Date of issue/Date of revision
:
10/22/2018
Date of previous issue
:
3/2/2018
Version
:69/12
K05400105
KRYLON® DURA-TOP® Floor Coating (Part A)
Haze Gray
SHW-85-NA-GHS-US
Page 10
Section 12. Ecological information
LogP
ow
BCF
Potential
Other adverse effects
:
No known significant effects or critical hazards.
Product/ingredient name
Epoxy Polymer
-31low
Soil/water partition
coefficient (KOC)
:
Not available.
Mobility in soil
Section 13. Disposal considerations
The generation of waste should be avoided or minimized wherever possible. Disposal
of this product, solutions and any by-products should at all times comply with the
requirements of environmental protection and waste disposal legislation and any
regional local authority requirements. Dispose of surplus and non-recyclable products
via a licensed waste disposal contractor. Waste should not be disposed of untreated to
the sewer unless fully compliant with the requirements of all authorities with jurisdiction.
Waste packaging should be recycled. Incineration or landfill should only be considered
when recycling is not feasible. This material and its container must be disposed of in a
safe way. Care should be taken when handling emptied containers that have not been
cleaned or rinsed out. Empty containers or liners may retain some product residues.
Avoid dispersal of spilled material and runoff and contact with soil, waterways, drains
and sewers.
:
Disposal methods
Section 14. Transport information
-
-
-
-
-
-
Not regulated.
Not regulated.
-
-
DOT
Classification
IMDG
UN number
UN proper
shipping name
Transport
hazard class(es)
Packing group
Additional
information
Environmental
hazards
Special precautions for user
Transport in bulk according
to Annex II of MARPOL and
the IBC Code
No.
No.
Not available.
:
Proper shipping name
:
Ship type
:
Not available.
Not available.
:
TDG
Classification
Not regulated.
-
-
-
No.
-
Mexico
Classification
Not regulated.
-
-
-
No.
-
Multi-modal shipping descriptions are provided for informational purposes and do not
consider container sizes. The presence of a shipping description for a particular
mode of transport (sea, air, etc.), does not indicate that the product is packaged
suitably for that mode of transport. All packaging must be reviewed for suitability
prior to shipment, and compliance with the applicable regulations is the sole
responsibility of the person offering the product for transport. People loading and
unloading dangerous goods must be trained on all of the risks deriving from the
substances and on all actions in case of emergency situations.
IATA
Not regulated.
-
-
-
No.
-
Date of issue/Date of revision
:
10/22/2018
Date of previous issue
:
3/2/2018
Version
:610/12
K05400105
KRYLON® DURA-TOP® Floor Coating (Part A)
Haze Gray
SHW-85-NA-GHS-US
Page 11
Section 14. Transport information
Pollution category
:
Not available.
Section 15. Regulatory information
SARA 313
SARA 313 (40 CFR 372.45) supplier notification can be found on the Environmental Data Sheet.
WARNING: This product contains chemicals known to the State of California to cause cancer.
California Prop. 65
Australia inventory (AICS)
: Not determined.
China inventory (IECSC)
: Not determined.
Japan inventory (ENCS)
: Not determined.
Japan inventory (ISHL)
: Not determined.
Korea inventory (KECI)
: Not determined.
Malaysia Inventory (EHS Register)
: Not determined.
New Zealand Inventory of Chemicals (NZIoC)
: Not determined.
Philippines inventory (PICCS)
: Not determined.
Taiwan Chemical Substances Inventory (TCSI)
: Not determined.
Thailand inventory
: Not determined.
Turkey inventory
: Not determined.
Vietnam inventory
: Not determined.
International regulations
International lists
:
Section 16. Other information
10/22/2018
History
Date of printing
Date of issue/Date of
revision
Version
Date of previous issue
::::10/22/2018
3/2/2018
6
Hazardous Material Information System (U.S.A.)
2
1
0
*
Health
Flammability
Physical hazards
Caution: HMIS® ratings are based on a 0-4 rating scale, with 0 representing minimal hazards or risks, and 4
representing significant hazards or risks. Although HMIS® ratings and the associated label are not required on
SDSs or products leaving a facility under 29 CFR 1910.1200, the preparer may choose to provide them. HMIS®
ratings are to be used with a fully implemented HMIS® program. HMIS® is a registered trademark and service
mark of the American Coatings Association, Inc.
The customer is responsible for determining the PPE code for this material. For more information on HMIS®
Personal Protective Equipment (PPE) codes, consult the HMIS® Implementation Manual.
SKIN CORROSION/IRRITATION - Category 2
Calculation method
SERIOUS EYE DAMAGE/ EYE IRRITATION - Category 2A
Calculation method
SKIN SENSITIZATION - Category 1
Calculation method
CARCINOGENICITY - Category 2
Calculation method
TOXIC TO REPRODUCTION (Unborn child) - Category 1
Calculation method
TOXIC TO REPRODUCTION (Fertility) - Category 2
Calculation method
SPECIFIC TARGET ORGAN TOXICITY (REPEATED EXPOSURE) - Category 2
Calculation method
Procedure used to derive the classification
Classification
Justification
Date of issue/Date of revision
:
10/22/2018
Date of previous issue
:
3/2/2018
Version
:611/12
K05400105
KRYLON® DURA-TOP® Floor Coating (Part A)
Haze Gray
SHW-85-NA-GHS-US
Page 12
Section 16. Other information
It is recommended that each customer or recipient of this Safety Data Sheet (SDS) study it carefully and consult
resources, as necessary or appropriate, to become aware of and understand the data contained in this SDS and
any hazards associated with the product. This information is provided in good faith and believed to be accurate
as of the effective date herein. However, no warranty, express or implied, is given. The information presented
here applies only to the product as shipped. The addition of any material can change the composition, hazards
and risks of the product. Products shall not be repackaged, modified, or tinted except as specifically instructed
by the manufacturer, including but not limited to the incorporation of products not specified by the manufacturer,
or the use or addition of products in proportions not specified by the manufacturer. Regulatory requirements
are subject to change and may differ between various locations and jurisdictions. The customer/buyer/user is
responsible to ensure that his activities comply with all country, federal, state, provincial or local laws. The
conditions for use of the product are not under the control of the manufacturer; the customer/buyer/user is
responsible to determine the conditions necessary for the safe use of this product. The customer/buyer/user
should not use the product for any purpose other than the purpose shown in the applicable section of this SDS
without first referring to the supplier and obtaining written handling instructions. Due to the proliferation of
sources for information such as manufacturer-specific SDS, the manufacturer cannot be responsible for SDSs
obtained from any other source.
Key to abbreviations
:
ATE = Acute Toxicity Estimate
BCF = Bioconcentration Factor
GHS = Globally Harmonized System of Classification and Labelling of Chemicals
IATA = International Air Transport Association
IBC = Intermediate Bulk Container
IMDG = International Maritime Dangerous Goods
LogPow = logarithm of the octanol/water partition coefficient
MARPOL = International Convention for the Prevention of Pollution From Ships, 1973
as modified by the Protocol of 1978. ("Marpol" = marine pollution)
UN = United Nations
Notice to reader
Date of issue/Date of revision
:
10/22/2018
Date of previous issue
:
3/2/2018
Version
:612/12
K05400105
KRYLON® DURA-TOP® Floor Coating (Part A)
Haze Gray
SHW-85-NA-GHS-US
Loading...