
KRYLON® Industrial TOUGH COAT™ Acrylic Enamel
OSHA Safety Green
Other means of
identification
Emergency telephone
number of the company
Section 1. Identification
THE SHERWIN-WILLIAMS COMPANY
KRYLON PRODUCTS GROUP
Cleveland, OH 44115
Relevant identified uses of the substance or mixture and uses advised against
Product Information
Telephone Number
Regulatory Information
Telephone Number
Transportation Emergency
Telephone Number
Section 2. Hazards identification
FLAMMABLE AEROSOLS - Category 1
GASES UNDER PRESSURE - Compressed gas
SKIN CORROSION/IRRITATION - Category 2
SERIOUS EYE DAMAGE/ EYE IRRITATION - Category 2A
SKIN SENSITIZATION - Category 1
CARCINOGENICITY - Category 2
TOXIC TO REPRODUCTION (Unborn child) - Category 2
SPECIFIC TARGET ORGAN TOXICITY (SINGLE EXPOSURE) (Respiratory tract
irritation and Narcotic effects) - Category 3
SPECIFIC TARGET ORGAN TOXICITY (REPEATED EXPOSURE) - Category 2
ASPIRATION HAZARD - Category 1
Classification of the
substance or mixture
Percentage of the mixture consisting of ingredient(s) of unknown toxicity: 17.7%
This material is considered hazardous by the OSHA Hazard Communication Standard
(29 CFR 1910.1200).
Date of issue/Date of revision

Section 2. Hazards identification
Obtain special instructions before use. Do not handle until all safety precautions have
been read and understood. Use personal protective equipment as required. Wear
protective gloves. Wear eye or face protection. Keep away from heat, hot surfaces,
sparks, open flames and other ignition sources. No smoking. Pressurized container: Do
not pierce or burn, even after use. Do not spray on an open flame or other ignition
source. Use only outdoors or in a well-ventilated area. Do not breathe dust or mist.
Wash hands thoroughly after handling. Contaminated work clothing should not be
allowed out of the workplace.
Get medical attention if you feel unwell. IF exposed or concerned: Get medical
attention. IF INHALED: Remove victim to fresh air and keep at rest in a position
comfortable for breathing. Call a POISON CENTER or physician if you feel unwell. IF
SWALLOWED: Immediately call a POISON CENTER or physician. Do NOT induce
vomiting. IF ON SKIN: Wash with plenty of soap and water. Take off contaminated
clothing. Wash contaminated clothing before reuse. If skin irritation or rash occurs:
Get medical attention. IF IN EYES: Rinse cautiously with water for several minutes.
Remove contact lenses, if present and easy to do. Continue rinsing. If eye irritation
persists: Get medical attention.
Store locked up. Protect from sunlight. Do not expose to temperatures exceeding 50
°C/122 °F. Store in a well-ventilated place.
Dispose of contents and container in accordance with all local, regional, national and
international regulations.
Read label before use. Keep out of reach of children. If medical advice is needed, have
product container or label at hand.
Hazards not otherwise
classified
Extremely flammable aerosol.
Contains gas under pressure; may explode if heated.
Causes serious eye irritation.
Causes skin irritation.
May cause an allergic skin reaction.
Suspected of damaging the unborn child.
Suspected of causing cancer.
May be fatal if swallowed and enters airways.
May cause respiratory irritation.
May cause drowsiness and dizziness.
May cause damage to organs through prolonged or repeated exposure.
Please refer to the SDS for additional information. Keep upright in a cool, dry place. Do
not discard empty can in trash compactor.
Supplemental label
elements
DELAYED EFFECTS FROM LONG TERM OVEREXPOSURE. Contains solvents which
can cause permanent brain and nervous system damage. Intentional misuse by
deliberately concentrating and inhaling the contents can be harmful or fatal. WARNING:
This product contains chemicals known to the State of California to cause cancer and
birth defects or other reproductive harm. FOR INDUSTRIAL USE ONLY.
Section 3. Composition/information on ingredients
Other means of
identification
CAS number/other identifiers
Date of issue/Date of revision

Section 3. Composition/information on ingredients
There are no additional ingredients present which, within the current knowledge of the supplier and in the
concentrations applicable, are classified as hazardous to health or the environment and hence require reporting
in this section.
Occupational exposure limits, if available, are listed in Section 8.
Get medical attention immediately. Call a poison center or physician. Wash out mouth
with water. Remove dentures if any. Remove victim to fresh air and keep at rest in a
position comfortable for breathing. If material has been swallowed and the exposed
person is conscious, give small quantities of water to drink. Stop if the exposed person
feels sick as vomiting may be dangerous. Aspiration hazard if swallowed. Can enter
lungs and cause damage. Do not induce vomiting. If vomiting occurs, the head should
be kept low so that vomit does not enter the lungs. Never give anything by mouth to an
unconscious person. If unconscious, place in recovery position and get medical
attention immediately. Maintain an open airway. Loosen tight clothing such as a collar,
tie, belt or waistband.
Immediately flush eyes with plenty of water, occasionally lifting the upper and lower
eyelids. Check for and remove any contact lenses. Continue to rinse for at least 10
minutes. Get medical attention.
Wash with plenty of soap and water. Remove contaminated clothing and shoes. Wash
contaminated clothing thoroughly with water before removing it, or wear gloves.
Continue to rinse for at least 10 minutes. Get medical attention. In the event of any
complaints or symptoms, avoid further exposure. Wash clothing before reuse. Clean
shoes thoroughly before reuse.
Remove victim to fresh air and keep at rest in a position comfortable for breathing. If it
is suspected that fumes are still present, the rescuer should wear an appropriate mask
or self-contained breathing apparatus. If not breathing, if breathing is irregular or if
respiratory arrest occurs, provide artificial respiration or oxygen by trained personnel. It
may be dangerous to the person providing aid to give mouth-to-mouth resuscitation.
Get medical attention. If necessary, call a poison center or physician. If unconscious,
place in recovery position and get medical attention immediately. Maintain an open
airway. Loosen tight clothing such as a collar, tie, belt or waistband.
Section 4. First aid measures
Description of necessary first aid measures
Most important symptoms/effects, acute and delayed
Can cause central nervous system (CNS) depression. May cause drowsiness and
dizziness. May cause respiratory irritation.
Can cause central nervous system (CNS) depression. May be fatal if swallowed and
enters airways. Irritating to mouth, throat and stomach.
Causes skin irritation. May cause an allergic skin reaction.
Causes serious eye irritation.
Over-exposure signs/symptoms
Adverse symptoms may include the following:
pain or irritation
watering
redness
Potential acute health effects
Date of issue/Date of revision

Section 4. First aid measures
Protection of first-aiders
No action shall be taken involving any personal risk or without suitable training. If it is
suspected that fumes are still present, the rescuer should wear an appropriate mask or
self-contained breathing apparatus. It may be dangerous to the person providing aid to
give mouth-to-mouth resuscitation. Wash contaminated clothing thoroughly with water
before removing it, or wear gloves.
Treat symptomatically. Contact poison treatment specialist immediately if large
quantities have been ingested or inhaled.
Adverse symptoms may include the following:
respiratory tract irritation
coughing
nausea or vomiting
headache
drowsiness/fatigue
dizziness/vertigo
unconsciousness
reduced fetal weight
increase in fetal deaths
skeletal malformations
Adverse symptoms may include the following:
nausea or vomiting
reduced fetal weight
increase in fetal deaths
skeletal malformations
Adverse symptoms may include the following:
irritation
redness
reduced fetal weight
increase in fetal deaths
skeletal malformations
See toxicological information (Section 11)
Indication of immediate medical attention and special treatment needed, if necessary
Section 5. Fire-fighting measures
Hazardous thermal
decomposition products
Specific hazards arising
from the chemical
Decomposition products may include the following materials:
carbon dioxide
carbon monoxide
metal oxide/oxides
Extremely flammable aerosol. In a fire or if heated, a pressure increase will occur and
the container may burst, with the risk of a subsequent explosion. Gas may accumulate
in low or confined areas or travel a considerable distance to a source of ignition and
flash back, causing fire or explosion. Bursting aerosol containers may be propelled from
a fire at high speed. Runoff to sewer may create fire or explosion hazard.
Use an extinguishing agent suitable for the surrounding fire.
Suitable extinguishing
media
Unsuitable extinguishing
media
Date of issue/Date of revision

Section 5. Fire-fighting measures
Promptly isolate the scene by removing all persons from the vicinity of the incident if
there is a fire. No action shall be taken involving any personal risk or without suitable
training. Move containers from fire area if this can be done without risk. Use water
spray to keep fire-exposed containers cool.
Fire-fighters should wear appropriate protective equipment and self-contained breathing
apparatus (SCBA) with a full face-piece operated in positive pressure mode.
Special protective
equipment for fire-fighters
Special protective actions
for fire-fighters
Section 6. Accidental release measures
Environmental precautions
Personal precautions, protective equipment and emergency procedures
Stop leak if without risk. Move containers from spill area. Use spark-proof tools and
explosion-proof equipment. Approach release from upwind. Prevent entry into sewers,
water courses, basements or confined areas. Wash spillages into an effluent treatment
plant or proceed as follows. Contain and collect spillage with non-combustible,
absorbent material e.g. sand, earth, vermiculite or diatomaceous earth and place in
container for disposal according to local regulations (see Section 13). Dispose of via a
licensed waste disposal contractor. Contaminated absorbent material may pose the
same hazard as the spilled product. Note: see Section 1 for emergency contact
information and Section 13 for waste disposal.
No action shall be taken involving any personal risk or without suitable training.
Evacuate surrounding areas. Keep unnecessary and unprotected personnel from
entering. In the case of aerosols being ruptured, care should be taken due to the rapid
escape of the pressurized contents and propellant. If a large number of containers are
ruptured, treat as a bulk material spillage according to the instructions in the clean-up
section. Do not touch or walk through spilled material. Shut off all ignition sources. No
flares, smoking or flames in hazard area. Avoid breathing vapor or mist. Provide
adequate ventilation. Wear appropriate respirator when ventilation is inadequate. Put
on appropriate personal protective equipment.
Avoid dispersal of spilled material and runoff and contact with soil, waterways, drains
and sewers. Inform the relevant authorities if the product has caused environmental
pollution (sewers, waterways, soil or air).
Stop leak if without risk. Move containers from spill area. Use spark-proof tools and
explosion-proof equipment. Dilute with water and mop up if water-soluble. Alternatively,
or if water-insoluble, absorb with an inert dry material and place in an appropriate waste
disposal container. Dispose of via a licensed waste disposal contractor.
Methods and materials for containment and cleaning up
For non-emergency
personnel
If specialised clothing is required to deal with the spillage, take note of any information in
Section 8 on suitable and unsuitable materials. See also the information in "For nonemergency personnel".
Section 7. Handling and storage
Put on appropriate personal protective equipment (see Section 8). Persons with a
history of skin sensitization problems should not be employed in any process in which
this product is used. Pressurized container: protect from sunlight and do not expose to
temperatures exceeding 50°C. Do not pierce or burn, even after use. Avoid exposure obtain special instructions before use. Avoid exposure during pregnancy. Do not
handle until all safety precautions have been read and understood. Do not get in eyes
or on skin or clothing. Do not breathe vapor or mist. Do not swallow. Avoid breathing
gas. Use only with adequate ventilation. Wear appropriate respirator when ventilation is
inadequate. Store and use away from heat, sparks, open flame or any other ignition
source. Use explosion-proof electrical (ventilating, lighting and material handling)
equipment. Use only non-sparking tools. Empty containers retain product residue and
can be hazardous.
Precautions for safe handling
Date of issue/Date of revision

Section 7. Handling and storage
Advice on general
occupational hygiene
Conditions for safe storage,
including any
incompatibilities
Eating, drinking and smoking should be prohibited in areas where this material is
handled, stored and processed. Workers should wash hands and face before eating,
drinking and smoking. Remove contaminated clothing and protective equipment before
entering eating areas. See also Section 8 for additional information on hygiene
measures.
Store in accordance with local regulations. Store away from direct sunlight in a dry, cool
and well-ventilated area, away from incompatible materials (see Section 10) and food
and drink. Protect from sunlight. Store locked up. Eliminate all ignition sources. Use
appropriate containment to avoid environmental contamination.
ACGIH TLV (United States, 4/2014).
STEL: 750 ppm 15 minutes.
STEL: 1782 mg/m³ 15 minutes.
NIOSH REL (United States, 10/2013).
OSHA PEL (United States, 2/2013).
OSHA PEL Z2 (United States, 2/2013).
NIOSH REL (United States, 10/2013).
STEL: 150 ppm 15 minutes.
STEL: 560 mg/m³ 15 minutes.
ACGIH TLV (United States, 4/2014).
NIOSH REL (United States, 10/2013).
TWA: 1800 mg/m³ 10 hours.
OSHA PEL (United States, 2/2013).
NIOSH REL (United States, 10/2013).
TWA: 1900 mg/m³ 10 hours.
ACGIH TLV (United States, 4/2014).
STEL: 1000 ppm 15 minutes.
ACGIH TLV (United States, 4/2014).
OSHA PEL (United States, 2/2013).
TWA: 15 mg/m³ 8 hours. Form: Total dust
AIHA WEEL (United States, 10/2011). Skin
sensitizer.
Section 8. Exposure controls/personal protection
Occupational exposure limits
Date of issue/Date of revision

Section 8. Exposure controls/personal protection
Use a properly fitted, air-purifying or air-fed respirator complying with an approved
standard if a risk assessment indicates this is necessary. Respirator selection must be
based on known or anticipated exposure levels, the hazards of the product and the safe
working limits of the selected respirator.
Chemical-resistant, impervious gloves complying with an approved standard should be
worn at all times when handling chemical products if a risk assessment indicates this is
necessary. Considering the parameters specified by the glove manufacturer, check
during use that the gloves are still retaining their protective properties. It should be
noted that the time to breakthrough for any glove material may be different for different
glove manufacturers. In the case of mixtures, consisting of several substances, the
protection time of the gloves cannot be accurately estimated.
Safety eyewear complying with an approved standard should be used when a risk
assessment indicates this is necessary to avoid exposure to liquid splashes, mists,
gases or dusts. If contact is possible, the following protection should be worn, unless
the assessment indicates a higher degree of protection: chemical splash goggles.
Personal protective equipment for the body should be selected based on the task being
performed and the risks involved and should be approved by a specialist before
handling this product. When there is a risk of ignition from static electricity, wear antistatic protective clothing. For the greatest protection from static discharges, clothing
should include anti-static overalls, boots and gloves.
Environmental exposure
controls
Emissions from ventilation or work process equipment should be checked to ensure
they comply with the requirements of environmental protection legislation. In some
cases, fume scrubbers, filters or engineering modifications to the process equipment
will be necessary to reduce emissions to acceptable levels.
Appropriate engineering
controls
Use only with adequate ventilation. Use process enclosures, local exhaust ventilation or
other engineering controls to keep worker exposure to airborne contaminants below any
recommended or statutory limits. The engineering controls also need to keep gas,
vapor or dust concentrations below any lower explosive limits. Use explosion-proof
ventilation equipment.
Wash hands, forearms and face thoroughly after handling chemical products, before
eating, smoking and using the lavatory and at the end of the working period.
Appropriate techniques should be used to remove potentially contaminated clothing.
Contaminated work clothing should not be allowed out of the workplace. Wash
contaminated clothing before reusing. Ensure that eyewash stations and safety
showers are close to the workstation location.
Individual protection measures
Appropriate footwear and any additional skin protection measures should be selected
based on the task being performed and the risks involved and should be approved by a
specialist before handling this product.
Section 9. Physical and chemical properties
Closed cup: -29°C (-20.2°F) [Pensky-Martens Closed Cup]
Flammability (solid, gas)
Date of issue/Date of revision

Section 9. Physical and chemical properties
13.5 kPa (101.325 mm Hg) [at 20°C]
Auto-ignition temperature
Kinematic (room temperature): <0.07 cm2/s (<7 cSt)
Kinematic (40°C (104°F)): <0.07 cm2/s (<7 cSt)
Partition coefficient: noctanol/water
Lower and upper explosive
(flammable) limits
Decomposition temperature
Section 10. Stability and reactivity
Hazardous decomposition
products
Avoid all possible sources of ignition (spark or flame).
Under normal conditions of storage and use, hazardous decomposition products should
not be produced.
Possibility of hazardous
reactions
Under normal conditions of storage and use, hazardous reactions will not occur.
No specific test data related to reactivity available for this product or its ingredients.
Section 11. Toxicological information
Information on toxicological effects
Date of issue/Date of revision

Section 11. Toxicological information
0.5 minutes
100
milligrams
72 hours 300
Micrograms
Intermittent
Specific target organ toxicity (single exposure)
Specific target organ toxicity (repeated exposure)
Respiratory tract
irritation and
Narcotic effects
Respiratory tract
irritation and
Narcotic effects
Respiratory tract
irritation and
Narcotic effects
Respiratory tract
irritation and
Narcotic effects
Target organs
Classification
Date of issue/Date of revision

Section 11. Toxicological information
ASPIRATION HAZARD - Category 1
ASPIRATION HAZARD - Category 1
ASPIRATION HAZARD - Category 1
Information on the likely
routes of exposure
Can cause central nervous system (CNS) depression. May cause drowsiness and
dizziness. May cause respiratory irritation.
Can cause central nervous system (CNS) depression. May be fatal if swallowed and
enters airways. Irritating to mouth, throat and stomach.
Causes skin irritation. May cause an allergic skin reaction.
Causes serious eye irritation.
Symptoms related to the physical, chemical and toxicological characteristics
Adverse symptoms may include the following:
respiratory tract irritation
coughing
nausea or vomiting
headache
drowsiness/fatigue
dizziness/vertigo
unconsciousness
reduced fetal weight
increase in fetal deaths
skeletal malformations
Adverse symptoms may include the following:
nausea or vomiting
reduced fetal weight
increase in fetal deaths
skeletal malformations
Adverse symptoms may include the following:
irritation
redness
reduced fetal weight
increase in fetal deaths
skeletal malformations
Adverse symptoms may include the following:
pain or irritation
watering
redness
Delayed and immediate effects and also chronic effects from short and long term exposure
Potential acute health effects
Date of issue/Date of revision

May cause damage to organs through prolonged or repeated exposure. Once
sensitized, a severe allergic reaction may occur when subsequently exposed to very low
levels.
Suspected of causing cancer. Risk of cancer depends on duration and level of
exposure.
No known significant effects or critical hazards.
Suspected of damaging the unborn child.
No known significant effects or critical hazards.
No known significant effects or critical hazards.
Potential chronic health effects
Numerical measures of toxicity
Potential immediate
effects
Potential delayed effects
Potential immediate
effects
Potential delayed effects
Section 12. Ecological information
Acute EC50 20.565 mg/l Marine water
Acute LC50 6000000 µg/l Fresh water
Crustaceans - Gammarus pulex
Acute LC50 10000 µg/l Fresh water
Acute LC50 5600 ppm Fresh water
Fish - Poecilia reticulata
Chronic NOEC 4.95 mg/l Marine water
Chronic NOEC 0.016 ml/L Fresh water
Chronic NOEC 0.1 ml/L Fresh water
Daphnia - Daphnia magna Neonate
Chronic NOEC 5 µg/l Marine water
Fish - Gasterosteus aculeatus Larvae
Acute EC50 12500 µg/l Fresh water
Algae - Pseudokirchneriella
subcapitata
Acute EC50 11600 µg/l Fresh water
Crustaceans - Gammarus
pseudolimnaeus - Adult
Acute EC50 6000 µg/l Fresh water
Daphnia - Daphnia magna Juvenile (Fledgling, Hatchling,
Weanling)
Acute LC50 5500 µg/l Fresh water
Fish - Oncorhynchus kisutch - Fry
Chronic NOEC 1000 µg/l Fresh water
Acute LC50 >1000000 µg/l Marine water
Fish - Fundulus heteroclitus
Acute LC50 843000 µg/l Fresh water
Fish - Pimephales promelas
Persistence and degradability
Date of issue/Date of revision

Section 12. Ecological information
Bioaccumulative potential
No known significant effects or critical hazards.
Soil/water partition
coefficient (KOC)
Section 13. Disposal considerations
The generation of waste should be avoided or minimized wherever possible. Disposal
of this product, solutions and any by-products should at all times comply with the
requirements of environmental protection and waste disposal legislation and any
regional local authority requirements. Dispose of surplus and non-recyclable products
via a licensed waste disposal contractor. Waste should not be disposed of untreated to
the sewer unless fully compliant with the requirements of all authorities with jurisdiction.
Waste packaging should be recycled. Incineration or landfill should only be considered
when recycling is not feasible. This material and its container must be disposed of in a
safe way. Empty containers or liners may retain some product residues. Do not
puncture or incinerate container.
Section 14. Transport information
Special
provisions
LIMITED
QUANTITY
Emergency
schedules (EmS)
LIMITED
QUANTITY, F-D,
S-U
Transport
hazard class(es)
Special
provisions
LIMITED
QUANTITY
Special
provisions
(ERG#126)
Special
provisions
LIMITED
QUANTITY
Date of issue/Date of revision

Section 14. Transport information
Special precautions for user
Transport in bulk according
to Annex II of MARPOL
73/78 and the IBC Code
Multi-modal shipping descriptions are provided for informational purposes and do not
consider container sizes. The presence of a shipping description for a particular
mode of transport (sea, air, etc.), does not indicate that the product is packaged
suitably for that mode of transport. All packaging must be reviewed for suitability prior
to shipment, and compliance with the applicable regulations is the sole responsibility
of the person offering the product for transport. People loading and unloading
dangerous goods must be trained on all of the risks deriving from the substances
and on all actions in case of emergency situations.
Section 15. Regulatory information
WARNING: This product contains chemicals known to the State of California to cause cancer and birth defects or other
reproductive harm.
Section 16. Other information
Hazardous Material Information System (U.S.A.)
Caution: HMIS® ratings are based on a 0-4 rating scale, with 0 representing minimal hazards or risks, and 4
representing significant hazards or risks Although HMIS® ratings are not required on SDSs under 29 CFR 1910.
1200, the preparer may choose to provide them. HMIS® ratings are to be used with a fully implemented HMIS®
program. HMIS® is a registered mark of the National Paint & Coatings Association (NPCA). HMIS® materials may
be purchased exclusively from J. J. Keller (800) 327-6868.
The customer is responsible for determining the PPE code for this material.
Date of issue/Date of revision

Section 16. Other information
It is recommended that each customer or recipient of this Safety Data Sheet (SDS) study it carefully and consult
resources, as necessary or appropriate, to become aware of and understand the data contained in this SDS and
any hazards associated with the product. This information is provided in good faith and believed to be accurate
as of the effective date herein. However, no warranty, express or implied, is given. The information presented
here applies only to the product as shipped. The addition of any material can change the composition, hazards
and risks of the product. Regulatory requirements are subject to change and may differ between various
locations and jurisdictions. The customer/buyer/user is responsible to ensure that his activities comply with all
country, federal, state, provincial or local laws. The conditions for use of the product are not under the control of
the manufacturer; the customer/buyer/user is responsible to determine the conditions necessary for the safe use
of this product. The customer/buyer/user should not use the product for any purpose other than the purpose
shown in the applicable section of this SDS without first referring to the supplier and obtaining written handling
instructions. Due to the proliferation of sources for information such as manufacturer-specific SDS, the
manufacturer cannot be responsible for SDSs obtained from any other source.
Date of issue/Date of revision