Krups 314, PROAROMA TIME User Manual

,
, ~~MCS@
Instructions for Use /Warranty /Guarantee of Performance
QUALITY... BY DESIGN
ProAroma Time
KRUPS
(Model # 314)
SPECIAL CORD SET INSTRUCTIONS
ming entangled in or tripping over a longer cord. B. Longer extension cords may be used if care is exercised in their use. C. If a long extension cord is used,(1) the marked electrical ratingof the
extension cord should be at least as great as the electrical ratingof the
appliance, (2) if the appliance is of the grounded type, the extension cord
should be a grounding-type 3-wire cord, and (3) the longer cord should be
arranged so that.it will not drape over the counter top or table top where it
can be pulled on by children or tripped over. D.This appliance has a polarized plug (one blade is wider than the other).To
reduce the risk of electric shock, this plug is intended to fit into a polarized
outlet only one way. If the plug does not fit fully into the outlet, reversethe
plug. If it still does not fit, contact a qualified electrician. Do notattempt to
modify the plug in any way.
CAUTION:
This appliance is for household use.Any servicing other than cleaning and user maintenance should be performed by an authorized service representative.
Do not immerse base in water or any other liquid.
To reduce the risk of fire or electric shock, do not remove the base. No user service able parts inside. Repair should be done by authorized service personnel only.
. Check voltage to be sure that the voltage indicated on the nameplate agrees
with your voltage.
. Never usewarm or hot water to fill the water container! Use cold water only! . Never refillthe water chamber while this KRUPScoffee maker is in operation, in
the "on" position. Turn the KRUPS coffee maker off and let cool down for 10
minutes before'refilling with water.
. Before turning your KRUPS coffee maker on, please make sure that:
1. the filter is properly inserted into the swivel filter;
2. the swivel filter is properly closed;
3. the lid for the glass carafe is properly attached to the glass carafe;
4. the glass carafe sits flat on the inside circle of the heating plate.
. Keep your hands and the cord away from hot parts of the appliance during ope-
ration. .
. Never clean with scouring powders or hard implements.
r
~
a
b
KRUPS
c
CD,.
~J
d
~Ik
auto off
,,-+1
time
m
~:
e
f
a: hinged water chamber lid b: release button
c: swing away filter holder d: carafe
e: warming plate f: hidden cord storage g: magnifiedwater level indicator h: LEDdisplay i: indicator light
~. --+p
on/off
j: carafe pre-warm k: aroma selector button
I: programmable auto shut off button m: temperature adjustment button
n: time set button 0: programmable timer button p: ON/OFF button, set minutes
q: set auto on/set hour button
q
2.II.....
~
,
e
,'\II \ 1T71U,
I)
I
~
C8
KRUPS "ProAromaTime"
Your new KRUPS "ProAroma Time" coffee maker has the following features: 0 Exclusive KRUPS deep-brew system
with special filtering action for maximum flavor.
0 Electronically controlled 3 brewing
cycles let you select a full-flavored 1-3 cup brew, a medium strength 4-10 cup brew or a strong 4-10 cup brew.
0 Swing away two-part filter holder with
release button is convenient to use and easy to clean.
0 "Stop'n SeNe" feature lets you seNe a
cup or two while brewing. The automatic filter seal allows you to remove the
carafe for 20 seconds without coffee dripping onto the warming plate.
0 Aroma Savor System lid locks in flavor
and aroma by creating a seal on the carafe lid.
0 Carafe Pre-Warming Cycle pre-warms
the carafe so every cup of coffee is hot, from first to last.
0 24 hour programmable timer lets you
program the coffeemaker for convenient "wake-up" coffee in the morning.
0 Adjustable temperature control lets you
set coffee keep-warm temperature in 6 increments.
0 Programmable auto shut-off lets you
select shut-off time from 1 to 5 hours after brewing.
0 Electronic decalcifying detection will
automatically alert you when the coffeemaker needs to be decalcified.
0 Magnified water level indicator is easy to
read.
0 Hinged water container lid will not get
lostandwillprotectwatercontainerfrom
dust and dirt.
6
0 KRUPSspecially designed heating and
tubing system minimizes calcification and leaves no residual water in the
system when brewing is finished.
0 Hidden cord storage allows you to set
the desired cord length.
Setting the Time
1. Plug in the Krups "ProAroma Time". Make sure that the coffee maker is turned off
(the red light should not be illuminated).
2. The LCD display will be flashing. This is your signal to set the digital clock.
3. Press the "time" button - (n) on the
selector panel. Press the "auto" button ~
(q) and advance to the proper hour.
Press the "on/off" button ~ (p) and
advance to set the precise minutes. The AM or PM indicator will be illuminated
and should you pass the time you wish to
set, just hold in the "auto" button ~ (q)
until desired time is reached.
4. To lock in the time, simply press the "time"
button.. (n) again (Note: the time will automatically set in after 4 seconds). The flashing dots in the LCD display will confirm that the time has been properly set.
Preparing Coffee
Before making your first pot of delicious coffee, we recommend operating the coffee
maker once or twice with water only, without ground coffee or a paper filter to remove any possible dust.
. Be sure that the water container is empty.
Remove literature, etc. if inserted in the water container.
. The lid of the glass carafe must be
properly positioned during the brewing process. Position the lid over the carafe
and snap the rectangular piece onto the
handle. The lid is then locked in place.
"
'r
.Make sure that the swing away filter (c)
is properly closed during the brewing process. When closing the swivel filter you willfeel a noticeable resistance
between the swivel filter and the base.
Push infirmlyuntil you hearthe filter
"click" into place.
. Caution: If the swivel filter is not
completely closed, the "Stop'n Serve" trigger will not function properly, which may cause hot water or hot coffee to
overflow.
. The "Stop'n Serve" mechanism is opened
as long as the glass carafe is inserted into the machine and sits properly on the warming plate and the swivel filter is properly closed.
Filling the Water Chamber
Openthehingedlid(seefigure.):
Pour in the desired quantity of water (see
figure"). The water level indicator shows
you how much water you are filling into the container.
The amount of freshly brewed coffee delivered after the brewing process will always be slightly less than the amount put
into the water container. This is due to the
minimal absorption of the water by the
ground coffee. Therefore, put in a little more water to begin with so that you will have the number of cups you desire.
Replace the carafe on the warming plate
with the glass carafe lid in position.
Putting in the Ground Coffee
To open the swing away filter holder, move the release button (b) to the right to swing
the filterout (see figure.). Insert a paper filter (we recommend KRUPS size 4) with
the seam pointing towards the handle of the filter holder (see figure.).
Instead of filter paper you can also use the KRUPS goldtone filter (model #053). (When ordering filter paper or the goldtone filter from KRUPS be sure to indicate that they are for model #314).
Put ground coffee into the paper filter (see figure.). We suggest using one level
KRUPS measuring spoon of ground coffee for each cup of robust brewed coffee.
After using your KRUPS coffee maker several times you can adjust the measure to suit your own taste.
Close the swivel filter and make sure that it
is completely closed (see figure.) .
& Attention!
Make sure th,pt the filter paper does not tip over when ctosing the swivel filter, or else the water might run between the filter
paper and the filter holder producing a very weak cup of coffee.
Aroma Selector Button
The "aroma" button provides you complete
control over brewing strength and brewing
cycles, to suit you personal taste.
Press the "aroma" button.. (k). The
current aroma setting will appear in the
LCD display. Press the "aroma" button (k)
again to display the next aroma selection,
and so on.
There are three selections from which to
choose:
I
Display
aroma
..
I Prol
I I
for 4-10 cups of
coffee; delivers a medium and more
mellow flavor.
7
~
aroma
..
aroma
-
Display
for 4-10 cups of coffee; delivers a stronger, more
CYJm
stimulating coffee, with a
powerful aroma.
for 1-3 cups' of
I L -31 I coffee; full flavor
i andaroma
& Note!
Once you press the carafe pre-warm
button, the function is stored in memory. The next time you make coffee, the carafe will automatically be pre-warmed.
Thefunction can be cancelled by pressing the carafe pre-warm button during the pre- warm stage. The light will then remain solid
red. Carafe pre-warming is automatically
cancelled in the event of a power shortage
or removal of plug.
Aroma Savor Lid
Approximately 4 seconds after you have made your aroma selection, the time will reappear in the display window. Please
note that the last-selected aroma setting
will remain in memory until manually
changed to a different selection.
To begin the brewing process, press the
"ON/OFF" button ~ (p). The indicator light
will illuminate, indicating the brewing process has begun (see figure.).
Carafe Pre-Warming Cycle
This feature allows you to pre-warm the
carafe before the brewing process begins. Follow the steps in "Filling the Water Chamber" and "Putting in the Ground
Coffee" . To start the process, select the coffee
strength you desire using the "aroma" button.. (k). Within 6 seconds, press the carafe pre-warm button Ii (j). The display
will say "on". Pressthe
indicator light will flash, indicating that you have chosen to pre-warm the carafe. Pre-
heating takes approximately 5 minutes, after which the brewing process will automatically begin. Once the carafe is
pre-heated, the indicator light will stop flashing, but remain solid red.
Oii! button (p). The
When the brewing cycle is complete, the last drop to leave the filter seals the opening within the lid of the carafe. When pouring, the stream of coffee forms a seal on the
carafe lid so the remaining coffee is in an airtight container. This reduces evaporation and heat loss, and protects the aroma and
freshness of the coffee.
"Stop'n Serve" Feature
The "Stop'n Serve"feature is KRUPS'
answer to the impatient coffee drinker's clamor for "a quick cup of coffee!" This device automatically stops the flow of brewed coffee through the filter cone if the glass carafe is removed from the warming plate during the brewing cycle. You have
about 20 seconds between the removal of the carafe and its being reinserted to allow the serving of one or two cups of coffee. The "Stop'n Serve" device closes off the filter cone so effectively that there is
virtuany no coffee-drip onto the warming
plate (one drop, at most!). Once the carafe is replaced, the brewing cycle and the flow of the coffee into the
carafe are resumed.
8
'1
& Caution
If the coffee does drip onto the warming plate after removal of the carafe, it is usually an indication that the small seal in the filter holder is missing or defective. It is also possible that too much ground coffee has been placed into the paper filter. This causes the water that jets into the filter cone to overflow between the paper filter
and the sides of the filter cone. This overflow carries coffee grounds with it
that interfere with the snap-shot action of the filter holder, thus allowing brewed coffee to continue to drip through.
If this blockage and subsequent dripping do occur, replace the glass carafe immediately and allow the full brewing cycle to run its course. Do not swing out the swivel filter until the brewing cycle is completed.
Setting "Wake-Up" Time
This feature enables you to enjoy freshly brewed coffee at any pre-selected time within a 24-hour period. To use this feature, you must first set the digital clock (see Setting the Time):
1. Press the "prog" button.. (0). The display will change from the current clock setting to "Wake-Up" setting The
~ symbol will appear in the display
and the display will not flash.
2. Immediately select the time in which you would like the brewing process to
commence (see diagram below).
I Display
Press the "prog"
button Setthe
hour Setthe
minutes
progr.
-
h
..
auto
min.
-
onioff
I []]ID
II; l:OID
[; 1:151
I
3. Once you have set the "Wake-Up" time, either press the "prog" key or wait approximately 4 seconds. The current clock time will reappear and the display colon will flash. To activate "Wake-Up"
setting press ~ button. A green light
will indicate the "Wake-Up" program has been set. The "Wake-Up" time is now stored in memory. If you wish to check the "Wake-Up" time that has tieen programmed, simply press the "prog." button and the time will be displayed.
Preparing "Wake-Up" Coffee
To enjoy delicious "Wake-Up" coffee that is freshly brewed and hot, first set the "Wake-
Up" time (see Setting the "Wake-Up"
Time).
. Put in ground coffee.
. Fill the water chamber to the desired
number of cups.
. Place the carafe back on the warming
plate.
. Press the "auto" button ~ (q). The
indicator light will turn green and the ~ symbol will appear in the display (see figure G). Enter the desired aroma setting, if you have not previously done so.
. At the pre-programmed time, the
indicator light will change from green to red, indicating the brewing process has
begun.
Setting the "Keep-Warm"
Temperature
The ProAroma Time has a "keep-warm"
feature that maintains coffee temperature in 6 increments. To set the "keep-warm" temperature, press the "temp" button- (m). The currently entered temperature
number will appear in the display.
9
By pressing the "temp." button, you are able to to select the desired level of
temperature (1-6).
~
Display
0
the coffee will be
C] I kept warm
gently
j]
after brewing,
temp.
..
the coffee will continue to be
) I
held at the brewing
temperature
IDisplay
autooff
Upon making your selection, the clock time will reappear in the display window after approximately 4 seconds. The automatic shut-off. can be adjusted at any time.
Note: The ProAroma Time may be manually shut off at any time by using
the "on/off" button.
Cleaning
lliJ
I --. I the5 lengthsof..
. the warming
Sh )
period
after brewing,
I 5-\
CIJ I
After approximately 4 seconds, the current clock time will reappear in the display. Please note that the temperature level can be altered at any time.
the temperature
I
at which coffee
is maintained
will be
increased.
Adjustable Auto Shut-Off
The ProAroma Time also lets you select how long you would like the coffee kept warm, from 1 to 5 hours, before
automatically turning itself off. To set the warming period, press the "auto off" button.. (I). The currently entered period will appear (ie; 2h) in the display window.
By continuously pressing the "auto off" button, the warming period will be
increasedbyonehouruntilthemaximum
period of 5 hours is reached.
. Always unplug this appliance before
cleaning. Clean the filter holder, the carafe and carafe lid in a solution of hot
water and mild liquid soap. These parts can also be placed in the upper level of your dishwasher for safe effective cleaning.
. Never use scouring agents. . Never immerse the appliance itself in the
water or any other liquid. To clean, simply wipe off with a soft, damp cloth.
. Never use a cloth to clean the inside of
the water chamber, as this might leave fuzzy deposits inthe chamber. Just rinse with cold water, periodically.
Decalcifying
Although your KRUPS coffee maker has the
most advanced water heating and pumping system, it will periodically need cleaning with a decalcifying agent
.This is due to the calcium (limestone)
found in drinking water,
10
"
. In some areas where the water is hard,
you will need to decalcify more frequently than in areas with soft water.
. It will also depend upon how often you
use your coffee maker. An automatic sensor has been built into your ProAroma Time which will indicate when your coffee maker needs decalcifying by dis- playing the message "CALC". This sensor is extremely sensitive and the "CALC" message may appear briefly in the display under
certain circumstances. This is of no importance, however, and should be
ignored. Decalcification is necessary only when "CALC" appears repeatedly or permanently in the display.The "CALC" display will remain visible until the "on/off" key is pressed. You should now decalcify the coffeemaker. We recommend using KRUPS original decalcifying agent for cleaning your
KRUPS coffeemaker. When used in accor- dance with the following instructions, it will
prolong the life of your coffeemaker.
How to decalcify
Dissolve contents of decalcifier in two cups of cold tap water. Pour solution into the water tank, then place the empty carafe.
and filterbasket in place. Press the "aroma"
button. Nowselect the "1-3" cup setting.
Press the "on/off" key. Allow the
decalcifying solution to completely run
through one cycle. Repeat this two orthree
times with cold liquid.
Rinse by cycling clean water through twice, pausing and turning the
coffeemaker "off" for a few minutes in
between each rinse ses;sion.
D;splay
I ~ ~[ [RLU I aroma I L -31 ..
on/off
& Caution
KRUPS decalcifying agent is a citric acid
which is harmless. However, we recommend
keeping it out of the reach of children.
Do not take internally. If swallowed accidently, drink several glasses of water or milk and consult your doctor.
For best results ...
...always use fresh, cold water (warm water
might be stale and have mineral deposits which would Impair the flavor of the coffee).
..,we recommend that you grind your own beans. Freshly ground beans deliver more aroma and flavor. Use one KRUPS measuring spoon of beans per cup.
... serve coffee immediately after brewing. ... never reheat coffee.
Hidden Cord Storage
The power cord can be tailored to the
length required by utilising the hidden cord
storage located underneath the coffee
maker (see figure.).
Limited One Year Warranty
Your KRUPS # 314 is covered by the
following warranty (glass carafes are
excluded from warranty):
If from date of purchase within one year
this KRUPS product fails to function
because of defects in materials or
workmanship, KRUPS North America, will
at its option, repair or replace the unit
.without charge, provided the owner has a
proof of date of purchase.
This warranty will be void if malfunction
was caused by damage to the product by
accident, misuse, use on frequency or
voltage other than marked on the product
and/or described in the instructions, abuse
including tampering, damage in transit, or use for commercial purposes. This
warranty gives you specific legal rights,
andyoumayalsohaveotherrightswhich
vary from state to state.
11
GUARANTEE OF PERFORMANCE
This fine KRUPS product is manufactured according to a rigid code of quality
standards, and, with minimum care, should give years of satisfying service. However, should the need arise for repairs or for replacement parts within or after the warranty period, please call our CONSUMERSERVICEDEPARTMENT:
(800)526-5377
24-hours a day, 7 days a week
You will be provided with specific instruction on how to get your product repaired.
The department willalso be able to answer any general product questions you may
have.
Before calling the Consumer Service Department, please have the type number of your Krups appliance available. You must have this information before calling our Consumer Service Department so that we may better answer your questions. The type number can be located by looking on the bottom of your appliance.
This product is Type #314.
Any general correspondance can be addressed to:
Krups North America, Inc.
P.O. Box 3900
Peoria, IL61612
ROBERTKRUPSGmbH &Co. KG' Postfach190460' D-42704Solingen 0594/ \:r/314
US 63623
Loading...