Control Locations
1. Snooze Button
2. Hour Button
3. Minute Button
4. Time Set Button
5. Alarm ON/OFF/SET Switch
6. Alarm SOUND/VIB/BOTH Switch
Operation
Plug the adaptor into the power outlet,
and connect to the clock (7). The entire
display will flash meaning the incorrect
time is being displayed. This is a
normal condition and will stop when
the correct time has ben set.
PM Indicator
A dot appears in the upper left hand
corner of the display indicating that the
time shown is PM.
Alarm on Indicator
A dot appears in the lower right hand
corner of the display indicating that the
alarm has been set.
Vibealert™ Alarm Clock
Operating Instructions
Time Setting
Press and hold the TIME SET Button
(4) and the HOUR Button (2) to
advance the hour display. Then press and hold the TIME SET Button (4) and the MINUTE
Button (3) to advance the minutes until the correct time is displayed. Be sure to set it
correctly in the AM or PM mode. The PM Indicator will be "ON" when the clock is reading
PM time and "OFF" when reading AM time.
Alarm Time Setting
Move the ALARM ON/OFF/SET Switch (5) to SET position To set the alarm, press and
hold the HOUR Button (2) and then press and hold the MINUTE Button (3) until the
correct alarm time is displayed. Be sure to set it correctly in the AM or PM mode.
To Operate Alarm (Sound and/or Vibration)
Move the ALARM SOUND/VIB/BOTH (6) to desired position - "SOUND" position for
sound alarm only, "VIB" for vibration only, or "BOTH" position for sound and vibration
alarm. The Alarm On Indicator will light up meaning the alarm is set at the preset time. To
silence the alarm, move the ALARM ON/OFF/SET Switch (5) to the "OFF" position.
Please connect the vibration pad (9) to the clock (8) for vibration alarm.
Snooze
When the alarm sounds simply press the SNOOZE Button (1) to temporarily silence the
alarm. The alarm will sound again 8-9 minutes later. This can be repeated again and again.
To silence the alarm, move the ALARM ON/OFF/SET Switch (5) to the "OFF" position.
Battery Back-up (Battery not included)
In the event of a power failure, this unit will automatically switch to a battery stand-by
circuit when a battery is installed. Open the BATTERY COMPARTMENT on the bottom
of the unit and install a 9-volt battery. Under battery operation, the clock will keep the time
running and the alarm will sound at the preset time. When relying on back up battery power
the time will not show on the display but the internal clock will continue to run.
Warning
• This product is not designed to be exposed to any form of liquid
• The VibeAlert™ alarm clock remains readily operable when the plug is connected to
a power outlet
Warranty
Krown Manufacturing, Inc. warrants that the VibeAlert™ alarm clock and bed shaker sold by Krown Manufacturing, Inc. is free from defects in materials and workmanship under normal use and service for one year. This
warranty is applicable only to the original purchaser of the VibeAlert™ alarm clock and bed shaker when accom
panied by a sales receipt stating the date of purchase and the name of the company from which purchased. This
warranty is in lieu of an excludes all other warranties expressed or implied including any implied warranty of
merchantability or fitness any of any obligations on the part of Krown Manufacturing, Inc. shall either replace or
repair the VibeAlert™ alarm clock and bed shaker at no cost to the original purchaser within one year of the date
of purchase. During a one year period the purchaser may return the VibeAlert™ alarm clock to Krown Manufac
turing, Inc. at the following address:
-
-
Krown Manufacturing, Inc.
ATTN: Repair Department
3408 Indale Road, Fort Worth, TX 76116
Shipping charges are at the customer's expense. Please include a check or money order made out to Known
Manufacturing, Inc. in the amount of $7.50 to cover shipping and handling. This warranty does extend to any
VibeAlert™ alarm clock and bed shaker made by Krown Manufacturing, Inc. which has been subjected to abuse,
neglect, accident, improper applications, improper installation, or to use in violation of the instruction furnished
by Krown Manufacturing, Inc. This warranty does not extend to or apply to any VibeAlert™ alarm clock and/or
bed shaker which has been repaired or altered by any person who has not been expressly approved by Krown
Manufacturing, Inc. Krown Manufacturing, Inc. shall not be liable for any special or consequential damages or
for loss or expense directly or indirectly arising from use of the products or any inability to use them either
separately or in combination with other equipment or product accessories or from any other cause. This warranty
is only applicable to a product purchased through Krown Manufacturing, Inc. or Compu-TTY, Inc.
dealer/distributor. Other than as stated herein, there are no other warranties whether by sample or model, by
description or quantity, whether expressed or implied and there are no implied warranties of fitness for a particular
purpose or of merchantability.
Loading...