KROMA LM5009, LM5015, LM5018 User Manual
LCD-TFT Monitors
LM5000
User Manual
LM5000D11-02
Edition 03
March 2004
KROMA T E L E C O M
Pol. Ind. Alcobendas - C/ La Granja, 80
28108 Madrid - SPAIN
Tel. (34-91) 661 45 14
Fax. (34-91) 484 03 49
e-mail: sales@kromatelecom.com
www.kromatelecom.com
Manual de Usuario Serie LM5000
- 1 -
INDEX
1. FRONT PANEL ......................................................................................................................2
1.1 DESCRIPTION AND FUNCTIONS OF EACH PART...........................................................3
2. REAR PANEL.........................................................................................................................4
2..1 DESCRIPTIONS AND FUNCTIONS:.................................................................................5
3. KEYBOARD............................................................................................................................6
3.1 COMMON KEYS FOR ALL THE EQUIPMENTS .................................................................6
3.2 SPECIFIC KEYS FOR LM5015 & LM5018 Equipments.......................................................8
3.3 EXPLANATIONS ABOUT THE KEYBOARD........................................................................9
4. MENUS...................................................................................................................................9
4.1 STATUS MENU....................................................................................................................9
4.2 MEMORY RECALL MENU................................................................................................. 11
4.3 SETUP MENU................................................................................................................. ... 12
4.3.1. SETUP MENU MANUAL..........................................................................................13
4.3.1.1.CALIBRATION VALUES MENU............................................................................14
4.3.1.2.GEOMETRY SETUP MENU (ONLY FOR RGB VIDEO SIGNAL)........................ 15
4.3.1.3. COLOUR SETTING MENU.................................................................................. 16
4.3.1.4. CAL WITH ACTIVE DATA....................................................................................17
4.3.1.5. SYSTEM OPTIONS CONFIGURATIONS MENU ................................................17
4.4. PASSWORD MENU..........................................................................................................19
4.4.1. EXPLANATION ON THE PASSWORDS....................................................................20
4.5 TECHNICAL MENU...........................................................................................................20
4.6 MEMORY STORE MENU..................................................................................................21
4.7 PROGRAM FUNCTION MENU..........................................................................................22
4.8. EMBEDDED AUDIO MENU (ONLY FOR SDI VIDEO SIGNAL) ......................................25
4.9 MENU REMOTE................................................................................................................ 26
4.9.1. EXPLANATIONS ABOUT THE NETWORK IDENTIFIER...........................................27
Manual de Usuario Serie LM5000
- 2 -
11.. FFRROONNTT PPAANNEELL
LM5009 LM5015
LM5018
LM5018
LM5018
A) The equipment Switch on / Switch off.
B) Calibration Diode
C) Optical Encoder
D) Keyboard
E) Tally Led Indicator
C
A
B C
D
E
A
B
D
E
E
A
B C
D
Manual de Usuario Serie LM5000
- 3 -
The equipment Switch on / Switch off.
A green led switch on will let us know that the equipment is activated.
Calibration Diode Led.
The calibration diode led will be on in case that the equipment present values and such
calibration values do not agree with. In opposite case it will be off.
The values that should be considered in the calibration are based on the inputs that it
has selected:
- Brightness, Contrast and Saturation, for composite video signal, PAL and SECAM.
- Brightness, Contrast, Saturation and Hue for composite video signal, NTSC.
- Brightness and Contrast for SDI, RGB (PC) video signal.
Optical Encoder.
The optical encoder serves to move through the different menus that the system offers
and to change values of the system. Moving the optical encoder in clock wise direction,
a value will be increased or the window of selection in the menus. Moving it in opposite
sense, a value will be decreased or the window of selection.
Keyboard.
The keyboard allows to execute operations that the system offers in a direct way,
without going to the menus.
Tally Led Indicator.
Using the Tally connector located at the rear panel, it will allow to select or to indicate
the active monitor, in which case it will be activated , in that case it will be swithed on.
1.1 DESCRIPTION AND FUNCTIONS OF EACH PART.
Manual de Usuario Serie LM5000
- 4 -
22.. RREEAARR PPAANNEELL
LM5009 LM5015
LM5018
A) Power
B) Serial Number & Power Supply
C) AES-EBU Audio Output (optional).
D) Analog Audio Output (optional).
E) Tally Input Indicator
F) Connection with the Remote Equipment.
G) Composite Video Inputs (A & B) (optional).
H) SDI Video Inputs (S1 & S2) (optional).
I) RGB (PC) Input (optional).
A B
C
E DF
G
H
I
A B
E
C
D
F
G
I
H
A
B
CD
E F
G
H
I
Manual de Usuario Serie LM5000
- 5 -
P
ower.
The power supply characteristics will have to agree with the ones indicated in label B.
Serial Number
This identification card allows to distinguish three basic parts:
- The equipment Serial number.
- Necessary Power supply for the equipment at issue (voltage and power).
- Options installed into the equipment (CCVS, SDI and/or RGB(pc).
AES
-EBU Audio Output .
Only it will be available if the SDI option is installed into the equipment.
Analog Audio Output .
Only it will be available if the SDI option is installed into the equipment.
Tally Input Indicator.
It allows to indicate the active screen.
Connection with the Remote Equipment.
Optionally, the TFT Monitors, series LM5000, have a remote equipment (RK5000) that
allows to control the screens remotely.
Composite Video Inputs
The equipment can have two inputs (CCVS A and CCVS B) in composite video, it
admits video signal in PAL, NTSC or SECAM.
SDI Video Inputs.
The equipment can have two inputs SDI (S1 and S2) with passive loop through
(75Ω termination)
R
GB (PC) Input
The equipment can have a RGB(pc) input, depending on the equipment admits the
following PC resolutions:
- LM5009A11, LM5015 and LM5018:
- VESA Standard Resolutions:
- 640x480 60Hz.
- 800x600 56Hz.
- 800x600 60Hz.
- 1024x768 60Hz
2.1 DESCRIPTIONS AND FUNCTIONS:
Manual de Usuario Serie LM5000
- 6 -
33.. KKEEYYBBOOAARRDD
LM5009
LM5015
LM5018
3.1 COMMON KEYS FOR ALL THE EQUIPMENTS
CCVS: Composite video input selection. The first time that the key is pressed
appears the current, and the second and the successive ones will cause a change of
video input. If the CCVS option is installed will appear an indicative text on the
screen, it will show the input selected in each time, and the presence or absence of
signal in the same one. If the CCVS option is not installed, it will appear a message
of absence of the CCVS option. After few seconds or pressing the ESC key such
message will disappear
automatically.
Manual de Usuario Serie LM5000
- 7 -
CDV: SDI input selection. The first time that the key is pressed appears the current,
and the second and the successive ones will cause a change of video input. If the
CDV option is installed will appear an indicative text on the screen, it will show
the input selected in each time, and the presence or absence of signal in the same
one. If the CDV option is not installed, it will appear a message of absence of the
CDV option. After few seconds or pressing the ESC key such message will
disappear automatically.
RGB: RGB input selection. In this case, only there will be one key pressing,
because there is only one RGB input. If the RGB option is installed will appear an
indicative text on the screen, it will show the input in each time, and the presence or
absence of signal in the same one. If the RGB option is not installed, it will appear
a message of absence of the RGB option. After few seconds or pressing the ESC
key such message will disappear automatically. The resolution detection is
automatic by the system.
CNT: Contrast Control on the screen. Once this key is pressed, it will show the
screen current value of contrast and if it agrees with the calibrated value (CAL), if
not (UNCAL). By means of the optical encoder (C in the front part), this value will
be able to be changed. Pressing the CAL key the contrast value will be calibrated.
After few seconds or pressing the ESC key such message will disappear
automatically.
BLK: Brightness Control on the screen. Once this key is pressed, it will show the
screen current value of brightness and if it agrees with the calibrated value (CAL), if
not (UNCAL). By means of the optical encoder (C in the front part), this value will
be able to be changed. Pressing the CAL key the brightness value will be calibrated.
After few seconds or pressing the ESC key such message will disappear
automatically.
SAT: Saturation Control on the screen. It is only for composite video signal. Once
this key is pressed, it will show the screen current value of Saturation and if it
agrees with the calibrated value (CAL), if not (UNCAL). By means of the optical
encoder (C in the front part), this value will be able to be changed. Pressing the
CAL key the saturation value will be calibrated. After few seconds or pressing the
ESC key such message will disappear automatically.
AUD & CHN: Compatible keys. Only it is available if the SDI option is installed.
They are configurables through PROGRAM FUNCTION menu. Depending on how
they are configurated, they will be working as the following function/operation:
- Access to EMBEDDED AUDIO menu.
- Audio channels output selection: It will allow to select the Audio channels output in
Analog or AES-EBU Digital. In this case, the Analog output has priority, so, the
output will be selected based on the same one.
The first time that this key is pressed it will indicate the last Audio channels outputs
selected and the second and successive ones will do an output channels change.
Manual de Usuario Serie LM5000
- 8 -
After few seconds or pressing the ESC key such message will disappear
automatically.
- AES-EBU Audio output channels selection: It will allow to select the AES-EBU
audio output channels.The first key pressing will indicate the last AES-EBU Audio
output channels selected and the second and successive ones will do an output
channels change. After few seconds or pressing the ESC key such message will
disappear automatically.
Analog Audio output channels selection: It will allow to select the Analog Audio
output channels. The first key pressing will indicate the last Analog Audio output
channels selected and the second and successive ones will do an output channels
change. After few seconds or pressing the ESC key such message will disappear
automatically.
- Volume control (only key AUD): Only it is allowed to change the analog audio
volume. Pressing this key it will show the current value for the volume. By means of
the optical encoder (C in the front part), this value will be able to be changed. After
few seconds or pressing the ESC key such message will disappear automatically.
The only difference between the two keys, is that key AUD can be configurated as
volume control, while the CHN can not, due to on LM5015 and LM5018 equipments
there is an associated key for this function (VOL).
STS: Access to the system menus.
ESC: To cancel an operation or to abandon a certain operation.
CAL: It allows to return to the calibrated value or to select an option from the
system menus.
SIZE: Screen aspect ratio (4:3 or 16:9). The first key pressing will indicate the
current aspect ratio on the screen, and the second and the successive ones will cause
a change of format. This is only for Composite and SDI video signals. After few
seconds or pressing the ESC key such message will disappear automatically.
VOL: Only it is allowed to change the analog audio volume. With this keystroke it
will show the current volume value that the equipment has. By means of the optical
encoder (C in the front part), this value will be able to be changed. After few
seconds or pressing the ESC key such message will disappear automatically.
APT: Aperture selection. This is only for composite video signals.When this key is
pressed, it will appear a menu, moving with the optical encoder (C in the front part)
and by means of the CAL key, we will be able to choose one of the available
options. In order to leave the menu we will press the ESC key.
3.2 SPECIFIC KEYS FOR LM5015 & LM5018 Equipments
Loading...