EN User Manual
Introducing your mobile phone
KRIP K1
Manual EN_V.2018.6.23
Learn about your mobile phone’s layout, keys, display and icons.
Note: Software updates happen frequently, so your phone may look a different.
Microphone & Headset
Earpiece
Flashlight
Charger Port
Right option button
Power button
Left option button
Preparing your mobile phone
Get started setting up your mobile phone for its first use.
1. Remove the back cover
Caution: don’t use tools to remove the cover doing so may damage your phone.
2. Insert the SIM Cards
Your phone has two SIM cards slots.
Caution: Make sure you use the correct size SIM cars and don’t cut the SIM Cards.
3. Insert the battery
Put on the back cover. Connect your charger to charge your phone fully, then turn on the power. Select your
language and follow the screen prompts to get started.
Home screen & Settings
From the home screen, you can access the “Menu” of the phone with the left option button and the “Phonebook”
with the right option button.
• Calls: You can access the dialer directly form the numeric keyboard of the phone or via the phonebook.
• Settings: To change your network, display brightness and more. To open “Settings” select the icon from
the menu.
Connecting to internet
Learn the basics to configure your phone and connect to internet.
1. Add a new connection
• In the menu list, select Settings to access to the phone configuration.
• Select the option “Connections”, then select “Network account” and Select “Options”. Now select “New
account”.
• Type in the parameters according with your carrier.
• The basic parameters are:
o Name
o APN (Access point)
o Username (optional)
o Password(optional)
• Some carriers use Proxy Servers, refer to your carrier configuration for more information.
• When you finish typing in the parameters needed, Select Save.
• To add another connection, repeat the steps.
• If you have multiples APN configuration for the same SIM card, chose which one you want to use going to
Menu -> Services -> Options -> Settings and select one APN profile from SIM1 or SIM2 network account
list.
FCC Caution:
Any Changes or modifications not expressly approved by the party responsible for compliance
could void the user's authority to operate the equipment.
This device complies with part 15 of the FCC Rules. Operation is subject to the following two
conditions: (1) This device may not cause harmful interference, and (2) this device must
accept any interference received, including interference that may cause undesired operation.
IMPORTANT NOTE:
Note: This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasona ble
protection against harmful interference in a residential installation.
This equipment generates, uses and can radiate radio frequency energy and, if not installed
and used in accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or television reception,
which can be determined by turning the equipment off and on, the user is encouraged to try to
correct the interference by one or more of the following measures:
—Reorient or relocate the receiving antenna
—Increase the separation between the equipment and receiver.
—Connect the equipment into an outlet on a circuit different from that to which the receiver is
connected.
—Consult the dealer or an experienced radio/TV technician for help.
Specific Absorption Rate (SAR) information
SAR tests are conducted using standard operating positions accepted by the FCC with the
PHONE transmitting at its highest certified power level in all tested frequency bands, although
the SAR is determined at the highest certified power level, the actual SAR level of the PHONE
while operating can be well below the maximum value.
Before a new model PHONE is a available for sale to the public, it must be tested and certified
to the FCC that it does not exceed the exposure limit established by the FCC, tests for each
PHONE are performed in positions and locations as required by the FCC.
For body worn operation, this model PHONE has been tested and meets the FCC RFexposure
guidelines when used with an accessory designated for this product or when u se d with an
accessory that contains no metal and that positions the handset a minimum of 5mm from the
body.
Non-compliance with the above restrictions may result in violation of RF exposure guidelines.
Loading...