KREZ Falco 3D pen
User Manual
Thank you for using this product, in order to operate the equipment better, please read
this manual carefully.
DC socket
Filament loading hole
OLED screen
Unload button/temperature +/Speed +
Mode button/temperature -/Speed -
Load button
Nozzle cover
Parts in package
1. AC/DC adapter 2.USB cable 3. Screwdriver 4.User manual 5.3D pen
Warning!
1. this equipment is suitable for children over 8 years old and adult.Children is only
allowed to use under adult guardianship
2. the nozzle is with high temperature ,do not touch it by hand
3. it is strictly prohibited to input any other material into the filament loading hole
4. prohibited to use the power adapter provided by other company
5. prohibited to use the filament provided by other company,cause different parameter of
filament
6. keep the pen away fromwater
7. keep the pen in a safe place ,where the children can not reach
Features:
·.high end metal housing,super slim design
·Can be driven by power bank, no need connect to AC/DC adapter
·Double click loading/unloading button to filling and remove filament automatically
·OLED screen, which can display company information, temperature, speed and
material
·OSD language: multi-language customized
Operation instructions
1.connect AC/DC adapter to AC power socket and 3D pen DC power socket (or use the USB cable
to connect with the power bank which output is more than 2A), when the OLED screen is on ,it
means power connected
2.press the filament loading button,it starts to heat,and the screen will display the temperature,then
it reaches the target,it means it is ready for loading filament
3.insert the 1.75mm filament into the "filament loading hole",keep pressing the "filament loading
button",the material will be loaded . Hold till plastic material comes out from the nozzle ,it means
the filament is ready.(double click the button can load the filament automatically, press the button
again to exit automatic mode)
4.temperature adjustment:before heating or temperature not reach preset degree, presss + or – to
adjust temperature , After temperature reach preset degree or under feeding filament,press the
mode button for 2 seconds,it will enter temperature adjustment mode,presss + or – to adjust
temperature,within operation for 2 seconds,it wille exit temperature mode
automatically.Temperature range is 130°C-230°C
5.speed adjustment :During feeding filament,press + or – to adjust temperature
6 unload filament:press load button to start heating,after temperature reach preset degree, press
unload button ,the filament will move out automatically
7.press increase mode button and unload filament button at the same time to switch ABS/PLA
mode
8. replace nozzle set: remove the screw on back side,then plug off the nozzle set
9. the pen will enter standby mode after 2 minutes no operation,and press the loading filament
button to wake it up.
10.do not touch the nozzle during working
Note
1.heating time may be affected by environmental temperature
2.the filament end should be cut correctly before loading
3.suggest to unload the filament after finish drawing
Trouble shooting
please follow the below instruction in case of any defect
default
reason
solution
screen can not be powered
on
The power adapter or plug line
defective
Repair or replace the power adapter
Motherboard defective
Repair or replace the motherboard
Socket lead off
sold the socket
No filament come out
from nozzle
Nozzle blocked
Replace the nozzle set
Temperature is not high enough
Replace the nozzle set or adjust the
temperature
No working temperature
Replace the nozzle set or check the
motherboard
Gear slips
Back wire, cleaning gear, cut off the
damaged supplies after the re loading
fail to load filament
unload filament and cut the end of filament
well
Motherboard defective
Repair or replace the motherboard
No working temperature
Heating part defective
Replace the nozzle set
Filament cut
correct
Wrong
Wrong
Specifications and parameters
Discharging mode: hot melt extrusion molding
Molding: three-dimensional molding
Print range: Unlimited
Feeding speed: adjustable
Printing material: PLA, ABS
Electric parameter: DC5V 2A 10W
The nozzle diameter: 0.6mm
Filament diameter: 1.75mm
Filament temperature: ABS210℃, PLA175℃
Power adapter electric parameter: 100-240V 50/60HZ 2A
Equipment dimension: 145mm*ø14mm
Equipment Net weight: 40g
Loading...