Krell Phantom III User Manual

Connecting the

KRELL

Phantom III
to Your System

Krell recommends using bal­anced interconnect cables.
Balanced interconnect cables
not only can minimize sonic
loss but are also immune to
induced noise, especially with
installations using long cables.
Balanced connections have
6 dB more gain than single­ended connections. When level
matching is critical, keep this
gain value in mind.

Operating the
Phantom III

Channel Balance
Adjustment

Position the preamplifier where you intend to use it in your system.

1. Neatly arrange and organize wiring to and from the preamplifier and all compo­nents. Separate the AC wires from any audio cables to prevent hum or other
unwanted noise from being introduced into the system.

2. Connect the outputs of your source equipment to the appropriate balanced
(11), or single-ended inputs (12) on the Phantom III.

3. Connect the main outputs (13) on the Phantom III to your amplifier’s inputs.

4. Connect the supplied AC power cord to the IEC power cord receptacle (17)
of the preamplifier.

5. Plug the other end of the AC power cord into AC power and turn on the rear
power switch. The display (3) shows

PHANTOM III SOFTWARE VERSION, and the

stand-by/power LED (4) illuminates red, indicating that the Phantom III is in
stand-by mode. When the display shuts off, the Phantom III is ready to be pow­ered on.

Note

Use only the power cord provided with the Phantom III to make the connection to AC power.
Operation with a power cord other than the one supplied by Krell can induce noise, limit cur­rent, or otherwise impair the ability of the preamplifier to perform optimally.

After the Phantom III is connected to your system and to AC power you may begin
operation:

1. Press the power button (1) on the front panel, or the remote control power key.
The standby/power LED turns blue. The display shows the factory default input:

S-1, and level: 000. The Phantom III is now in the operational mode.

2. With the preamplifier output muted, or the volume fully attenuated, select a
source manually using the front panel input select buttons (5 or 6) or the remote
input select keys. Start playing the source. Use the level control knob (10) or the
remote level keys to set the volume to a comfortable level.

3. To return the preamplifier to the stand-by mode, press the power button (1)
or remote power key. (We recommend leaving the Phantom III in the stand-by
mode when it is not playing music.)

The balance function allows adjustment of the left and right balance. The options
are:

CENTER, L .5-5 dB <, R .5-5 dB >. The remote control has direct keys (D) to make

these adjustments. For front panel adjustment follow the steps listed below.

1. Press the preamplifier menu button (9), then use the level control knob, or the
remote control up and down keys to select:

BALANCE.

2. Press the enter button (8) or remote enter key. The display shows the default
mode:

CENTER.

3. Use the level control knob, or the up and down keys, to select the desired bal­ance option from 0 to +5 dB in .5 dB increments, left or right.

4. Press the enter button or key to confirm the selection. The display reads:

BALANCE.

5. Press the menu button to exit the menu.

THE LEADER IN AUDIO ENGINEERING

Getting Started

The owner's reference for this
product, including a detailed
description of features, technolo­gies, and warranty is available on
the web at: www.krellonline.com

Overview

WARNINGS

This product complies with the
EMC directive (89/336/EEC)
and the low-voltage directive
(73/23/EEC).
This CLASS 1 apparatus must
be connected to a MAINS
socket outlet with a protective
earthing connection.

Unpacking

Note

Save all packing materials. If you
need to ship the Phantom III in
the future, repack the unit in its
original packaging to prevent
shipping damage.

Placement

Phantom III

Stereo Preamplifier

QUICK SETUP GUIDE

Thank you for your purchase of the Krell Phantom III Stereo Preamplifier. The Phantom
III features Krell Current Mode circuit topologies, balanced technology, and a robust
power supply for exceptional audio performance. The Phantom III preamplifier is the
first Krell preamplifier to include an optional digital input module. It is also the first
Krell preamplifier to include a headphone output. A thoughtful suite of menu options
ensures that the Phantom III can be customized for the greatest ease of operation.

The preamplifier’s front panel provides power, input selection, level control, menu
functions, and status display. The rear panel allows connection to audio sources,
power amplifiers, AC power, and other system components.

The remote control provides power, preamplifier, level control, navigation and
customization functions, CD and DVD player controls and menu configuration.

Do not place the preamplifier where it could be exposed to dripping or splashing.

Do not remove or bypass the ground pin on the end of the AC cord. This may cause radio fre­quency interference (RFI) to be introduced into your playback system.

The ventilation slots on the top and bottom of the preamplifier must be unobstructed at all
times during operation. Do not place flammable material on top of or beneath the component.

Turn off all systems’ power before connecting the preamplifier to any component.

Make sure all cable terminations are of the highest quality, free from frayed ends, short circuits,
or cold solder joints.

THERE ARE NO USER-SERVICEABLE PARTS INSIDE ANY KRELL PRODUCT

1. Open the shipping box and remove the top layer of foam. You will see these
items:

1 Preamplifier chassis
1 IEC connector (AC power) cord
1 Remote control

2. Carefully remove all items from the shipping box.

3. Place the preamplifier in a safe location and remove the protective plastic wrap­ping.

We recommend that you place the preamplifier on a firm, level surface, away from
excessive heat, humidity, or moisture. The preamplifier requires at least two inches
(5 cm) of clearance on each side and at least two inches (5 cm) of clearance above
to provide adequate ventilation. Installations inside cabinetry may need extra venti­lation.

2 AAA remote batteries
1 T-10 Torx wrench for remote
1 Quick Setup Guide

MODEL Phantom III Preamplifier

4 Krell Phantom III

Krell Industries, LLC., 45 Connair Road,Orange, CT 06477-3650 USA
TEL [phone], FAX [phone], E-MAIL [e-mail]
WEB SITE http://www.krellonline.com

SERIAL NUMBER

AC POWER GUIDELINES

The Phantom III preamplifier has superb regulation and does not require a dedi­cated AC circuit. Avoid connections through extension cords or multiple AC adapt­ers. High quality 15 amp AC strips are acceptable. The use of AC line conditioning
devices is not recommended. The features provided by these devices are already
on board the Phantom III.

Krell Phantom III 1

Figure 1 The Phantom III Front Panel

Figure 3 The Phantom III Back Panel

Front Panel

Remote
Control

Figure 2 The
Phantom III
Remote Control

1 Power

Use this to switch the
preamplifier between
stand-by and opera­tional modes.

2 Display

This provides channel
status messages, in­cluding input selection,
volume level, balance
offset, and menu selec­tions.

3 Infrared sensor

This receives com­mands from the remote
control. Make sure this
is not obstructed.

4 Stand-by/Power LED

This preamplifier LED
illuminates red (stand­by) when the Phantom
III is plugged into a stan-

dard AC wall receptacle
and rear power switch is
on. The LED illuminates
blue (operational mode)
when the power button
(1) is pressed while the
Phantom III is in stand­by mode.

5 Analog Input selectors

Use these to select
the corresponding
rear panel input that is
connected to a single­ended (S-1, S-2, S-3), or
balanced (B-1, B-2) ana­log source. The display
(2) shows the selected
input and volume level.
Pressing the input but­ton on the active source
will mute all outputs.
A second press will
unmute the outputs.

Keys labeled 1 to 10

have the same function
(and callout number) as
the front panel controls.

Keys labeled A through

K are unique to the re-

mote control, and are
described below:

A Phase key

Inverts the polarity of
the audio signal. A
lowercase i is displayed
when the polarity is
inverted.

B Mute key

Use this mute all out­puts. A second press
of the mute key will
unmute the outputs.

C Sel(ect) key

Cycles through the digi­tal inputs. This is only
active when the optional

6 Digital Input selec-

tor (functional with
optional D/A converter
module)

Use this to select the
D/A converter module.
Pressing and holding
the digital button will
cycle through the addi­tional digital inputs.

7 Headphone Jack

1/4" stereo headphone
jack. The main outputs
are muted when head­phones are being used.

8 Enter button

Use this to configure the
menu functions of the
Phantom III. See menu
(9).

D/A converter module is
installed.

D Bal(ance) keys

Use to balance left and
right output levels.

E Transport keys

These keys are func­tional with all Krell CD
and DVD players.

F CD key

Press this to make the
transport keys operate
Krell CD players.

G Direction keys

Use these keys to
navigate CD and DVD
menus.

H Select Key

Use this to make selec-

9 Menu button

Use this to access the
menu functions of the
Phantom III. For
more information,
see Customizing the
Phantom III, in the
owner’s reference.

10 Level control knob

Use this knob to
increase or decrease
system volume level.
The level control knob
or keys also select
menu options that cus­tomize the Phantom III.

tions from CD and DVD
menus.

I DVD key

Press this to make the
transport keys operate
DVD players.

J Menu key

Use this to enter CD or
DVD player menus.

K Title key

Use this with CD or
DVD player menus.

Note

The remote is shipped

with two AAA batteries
that have to be instal­led. Use the supplied
Torx wrench to remove
the battery panel, then
install the batteries.

Back Panel

Customizing
the
Phantom III

11 Balanced inputs: B-1

and B-2

These XLR balanced
analog source input
connectors are wired
as follows:

Pin 1 Ground

Pin 2 Non-inverting
Pin 3 Inverting

12 Single-ended inputs:

S-1, S-2, and S-3

There are 3 single­ended analog source
inputs with RCA con­nector pairs.

13 Main outputs

The Phantom III is
equipped with one bal­anced XLR output pair
and one single-ended
RCA output pair.

Configurable
Functions

AC Mains
Balance (channel)
Balance (input trim)
Display, Info
Input Level Trim
Input Name, Input Phase
Input Trigger, Mute,
Output Trigger, Recall,
Save, Theater.

The menu button or key
(9) allows you to configure
functions. Enter the menu
to view the list of configu­rable functions.

Select a function to view
a submenu of the list of
options that configure the
function. You can configure
some options as well, if a
second submenu appears
when you select an option.

14 RS-232 port

This port receives mes­sages from a computer­based control system,
providing integrated
control of all preamplifier
functions. For details,
see the developer's
reference: RS-232 Port:

Sending Commands
and Interpreting Data.

15 RC-5 in

This remote connector
is used with third-party
remote control systems
that provide RC-5 (IR)
data via a wired con­nection. A stereo tip,
ring, sleeve 1/8” mini
connector is used in the
following configuration:
Tip = RC-5 data
Ring = +5 V
Sleeve = GND.

Navigation
Conventions

Navigating the preamplifier
menu is straightforward and
consistent throughout, using
4 functions and the menu
option BACK.

9 Menu Button or Key

To enter the menu,
press the menu button
or key. Once you are
in the menu, you can
press the menu button
or key to exit the menu.

10 Level Control Knob

or Up and Down Keys

Use the level control
knob or the up and
down keys on the re­mote control to scroll
forward and backward
through the menu hier­archy. Each menu list is
a continuous loop.

16 12 VDC in/out

(12 V trigger)

There are 2 outputs and
one input that send and
receive 12 VDC power
on/off (trigger) signals
to and from other Krell
components, and other
devices that incor­porate a 12 V trigger.
This allows other com­ponents to be turned
on/off, or to/from stand­by, through the remote
control.

For more information,

see Input Trigger in the
owner’s reference.

8 Enter Button or Key

Press this button or key
to select a function or
a configuration option,
and confirm a selection

3 Front Panel Display

The display shows the
active function and con­figurable options.

BACK

Select

BACK to scroll

backwards through
the menu hierarchy, or
to exit a menu option
without confirming that
option.

17 IEC power cord

receptacle and power
switch

This is for use with the
provided AC power
cord. Plug the other
end into an AC Mains
supply capable of sup­plying the correct AC
voltage and current for
the power supply. This
connector and power
cord must remain
unobstructed for easy
removal in case of an
emergency.

18 Optional D/A

Converter Module

Location for future
plug in D/A converter
module.

For more information on
menu configuration, review
the Owner’s Reference on
the Krell website at www.
krellonline.com. Navigate to
Downloads/ Current, then
select the Phantom III from
the product list. The publi­cation list for the Phantom
III appears.

2 Krell Phantom III Krell Phantom III 3

This product is manufactured in the United States of America. Krell ® is a registered trademark of Krell Industries, LLC., and is restricted for
use by Krell Industries, LLC. its subsidiaries, and authorized agents. Krell Current Mode™ and Evolution CAST™ are trademarks of Krell
Industries, LLC. All other trademarks and trade names are registered to their respective companies.
© 2012 by Krell Industries, LLC., All rights reserved.