The Leader in Audio Engineering
Instructions for Use, v 98.0
KAV-150a
Power Amplifier
Owner’s Reference
KAV-150a
Power Amplifier
Contents
Page
INTRODUCTION
UNPACKING
Krell® Industries, Inc.
45 Connair Road
Orange, CT 06477-3650 USA
TEL 203-799-9954
FAX 203-799-9796
E-MAIL krell@ krellonline.com
WEB SITE www.krellonline.com
PLACEMENT
Cabinetry Considerations
AC Power Guidelines
CONNECTING THE KAV-150a
TO YOUR SYSTEM
Input and Output Connections
Configuring the KAV-150a
for Bridged Operation
AMPLIFIER OPERATION
On/Off and Stand-by Operation
System Noise Considerations
WARRANTY
RETURN AUTHORIZATION
PROCEDURE
SPECIFICATIONS
4
4
5
5
6
6
6
7
8
9
Back Cover
© 1998 by KRELL® Industries, Inc. All rights reserved
P/N I960101900088
CE Marking
This product complies with the EMC directive (89/336/EEC) and the low-voltage
directive (73/23/EEC).
Introduction
®
Thank you for your purchase of the Krell
KAV-150a Power Amplifier. The name
Krell® has always represented components
that are the premier performers in their
product categories. The KAV-150a power
amplifier continues in this Krell® tradition
The KAV-150a is a stereo amplifier that
may be bridged into monaural operation.
Designed as a compact component with
exceptional sound, the KAV-150a may be
interfaced easily into multi-amplifier systems using the 12 V trigger and the bridg-
ing capability. The KAV-150a uses proven
Krell®circuits built with the same high quality resistors, output devices, and internal
electrical components used in all other
Krell®products. From input to output, the
KAV-150a uses discrete, fully complementary circuitry. All circuits up to the driver
stage operate in pure Class A. The
KAV-150a employs a wide bandwidth
design with a very low negative feedback for
sonic accuracy throughout the frequency
spectrum.
The KAV-150a is backed by a comprehensive customer satisfaction policy and one
of the most advanced service facilities in
the industry. For detailed information on
the terms and conditions of service, please
consult your warranty registration card, or
®.
contact your dealer, distributor, or Krell
Unpacking
1. Open the box and remove the top layer of
foam. You will see these items:
1 KAV-150a
1 AC power cord
spare speaker fuses
2
1 packet containing an introductory
letter from Dan D’Agostino, C.E.O.,
the Owner’s Reference and the
Warranty Registration Card
Note
ff any of these items are not included, please
contact your authorized Krel/~ dea/er or dis-
tributor immediate/y for assistance.
Carefully remove the unit and acces-
2.
sories from the box. Remove the protec-
tive plastic wrap from the unit.
Note
Save all packing materials, ff you must
ship your KA V-150a in the future, repack
the unit in its original packaging to prevent
transit damage.
This owner’s reference manual contains
important information on the placement,
installation, and operations of the KAV-150a.
Please read this information carefully. A
thorough understanding of these details
will help insure satisfactory operation and a
long life for the KAV-150a and related system components.
KRELL® KAV-150a English Page 3 of 12
THERE ARE NO USER-SERVICEABLE
PARTS INSIDE ANY KRELL® PRODUCT
Please contact your authorized dealer,
distributor, or KrelP, if you have any
questions not addressed in this reference manual.
Placement
WARNING
The amplifier must not be located where it
could be exposed to dripping or splashing
fluids.
Before you install the KAV-150a into your
system, review the following guidelines to
choose the location for the KAV-150a. This
will facilitate a clean, trouble-free installation.
The KAV-150a does not require any type of
special rack or cabinet for installation. For the
dimensions of the KA V- 150a, see
Specifications on page 10.
Place the KAV-150a amplifier on a firm level
surface away from dirt or moisture. Ideally,
the amplifier should be placed as close to
the speakers as possible. Run long bal-
anced interconnect cables to the amplifier
and keep the speaker cable length to a min-
imum. Speaker cable adds impedance to
the load the amplifier must drive, regardless
of the cable’s gauge. All KrelP amplifiers will
drive the lowest impedances with ease, but
when impedance is added due to long
cable lengths, amplifier power is wasted in
the cable. Long speaker cables reduce the
maximum power that can be delivered to
the speakers.
CABINETRY CONSIDERATIONS
The KAV-150a amplifier can become quite
warm under normal operation. Install the
KAV-150a in a location that provides unobstructed ventilation.
IMPORTANT
The ventilation grids on top of the KA V- 150a
need to be unobstructed at all times during
operation. Do not place flammable material
on top of or beneath the KAV-150a. For
installation inside cabinet~ extra ventila-
tion may be necessary. Make sure the
KAV-150a has adequate air circulation.
Generally two inches of clearance on each
side of the amplifier and eight inches of
clearance above the amplifier will provide
adequate ventilation. In more extreme
instances, small fans can aid in removing
excess heat from internal spaces. Contact
your dealer, distributor, or Krell® for more
information.
AC POWER GUIDELINES
For best performance, Krell® recommends
using a dedicated AC power line rated at a
minimum of fifteen amps with the KAV-150a
amplifier. The KAV-150a amplifier should
only be operated with the power cord supplied. Please consult your dealer, distributor,
or Krell® before using any devices designed
to alter or stabilize the AC power for the
KAV-150a.
Page 4 of 12 English KRELL® KAV-150a
Connecting the KAV-150a
to Your System
have 6dB more gain than single-ended
connections. When level matching is crit-
ical, keep this specification in mind.
WARNING
When making connections to this component or any other, make sure the power
amplifier is off and the preamplifier is in the
mute or stand-by mode. Make sure all cable
terminations are of the highest quality, free
from frayed ends, shorts, or cold solder joints.
INPUT AND OUTPUT CONNECTIONS
To prevent the introduction of hum or other
noise into the system, organize all wiring
between the KAV-150a and other system
components neatly. Separate AC wires
from audio cables.
1. Connect the cables from your speakers
to the output terminals of the amplifier.
The KAV-150a amplifier utilizes fiveway binding post speaker terminals for
the left and right channels. The speaker
terminals accept spade lugs, bare wire,
banana plugs, or pins. The red terminals are used for positive connections
and the black terminals are used for the
negative connections.
2. Connect the interconnect cables from
your preamplifier to the input terminals of
the amplifier.
The KAV-150a amplifier is equipped
with balanced and single-ended inputs.
The balanced inputs use three pin XLR
connectors and the single-ended inputs
use RCA connectors. Krell® recom-
mends the use of balanced intercon-
nects. Balanced interconnects not only
have the ability to minimize sonic loss
but also have immunity to induced noise,
especially for installations using long
cable lengths. Balanced connections
WARNING
Use only one set of inputs to the amplifier at
a time. The KAV-150a amplifier is shipped
with shorting pins in the XLR inputs. These
pins should remain in the XLR inputs if the
KAV-150a amplifier is operating in the single-ended mode. When the shorting pin is
inserted, pins 1 and 3 are shorted together.
The shorting pins must be removed to con-
nect the KAV-150a amplifier for balanced
operation.
The XLR pin
below:
Pin 1
Pin 2
Pin 3
Connect the receptacle end of the AC
power cord to the IEC power connector in
the back panel of the KAV-150a. Connect
the AC power cord wall plug into a stan-
dard AC wall outlet.
4. The amplifier is now ready for operation.
See Amplifier Operation, on page 6.
12 VDC REMOTE POWER IN
This input accepts 12 volt power on/off
signals from other Krell® components, as
well as from other devices that incorporate a 12 volt power on/off trigger output.
This allows for remote turn on/off of the
KAV-150a with the power activation of
another Krell® component as well as with
other components used in a custom
installation.
configuration is described
Ground
°)
Non-inverting (0
°
Inverting (180
)
KRELL® KAV-150a English Page 5 of 12
12 VDC REMOTE POWER OUT
This output sends 12 volt power on/off signals to other Krell® components, as well as
other devices that incorporate a 12 volt
power on/off trigger input. This allows for
remote turn on/off of the KAV-150a with the
power activation of another Krell® component as well as with other components used
in a custom installation.
Note
Consu/t the owner’s manua/ of any device
used in a custom insta//ation to take furl
advantage of the remote capabi/ity of the
KAV-150a.
CONFIGURING THE KAV-150a
FOR BRIDGED OPERATION
The KAV-150a may be configured to operate
in a bridged mode. To implement this configu-
ration:
1. Turn the KAV-150a off.
2. Locate the red switch on the back of the
amplifier and slide it from the NORMAL
position to the BRIDGED position. The
numera/ 2 will appear on the switch, when
the switch is in the BRIDGED position.
Connect the interconnect cable to the
3.
BRIDGED input, either balanced via the
XLR connector or single-ended via the
RCA connector. Do not use both inputs
simultaneously. Connect the speaker
cables to the speaker terminals labeled
BRIDGED(-) and BRIDGED(+). The
lifier is now ready for bridged operation.
Amplifier Operation
It is easy to understand the operation of the
KAV-150a amplifier. However, great care
needs to be exercised when operating a system that includes the KAV-150a, because of
the amplifier’s enormous power output.
Switching between active sources without
muting the preamplifier output, or bumping/miscuing a cartridge, can generate large
transients at low frequencies. The KAV-150a
amplifier may generate enough power with
these transients to .damage most loudspeak-
ers. All switching of sources should be done
with the preamplifier level either muted or fully
attenuated. Do not change inputs to the ampli-
fier while the amplifier is on.
Note
Care must be taken when setting high p/ayback leve/s. Because of their tremendous
reserve of c/ean power, Kre//~ amp/ifiers
can safe/y drive speakers to higher sound
pressure /evels than other amplifiers.
A/ways turn the/eve/down at the first sign
of speaker distress.
ON/OFF AND STANDBY OPERATION
When powering up any system, amplifiers
should always be turned on last and turned off
first.
1. Press the power button on the front panel
of the KAV-150a Power Amplifier.You will
hear a click. The amplifier is ready for
operation.
2. With the system preamplifier in the mute
position, or the volume control fully atten-
uated, select a source. Turn the volume
control up to the desired listening level.
3. When .turning the system off, lower the
volume of the system preamplifier com-
pletely or place it into the mute or standby position. Turn the KAV-150a off. It is
now safe to tum off the rest of the system.
Page 6 of 12 English KRELL® KAV-150a
SYSTEM NOISE CONSIDERATIONS
AC grounding becomes critical when con-
necting high performance audio components.
When mixing and matching audio compo-
nents, each with their own ground potential, a
low frequency hum may occur in one or both
speakers. This often occurs when introducing
a new component into a system.
If there is a low frequency hum emanating
from the speakers when the KAV-150a
amplifier is placed into the system, follow
these simple troubleshooting steps before
contacting your authorized KrelP dealer, dis-
tributor, or Krell®:
1. Check all input and output connections,
making sure they are of sound construction. With the amplifier off, remove the in-
terconnect wiring and turn the amplifier
on. If the hum disappears, turn the amplifier off and reinsert one of the interconnect cables. Then turn the amplifier back
on. If the hum reappears with one or both
interconnects reinserted, there may be a
defective cable. Have the interconnect
cabling checked before proceeding.
If the interconnects prove to be sound,
=
you may be experiencing a ground loop.
This can often be easily eliminated. Contact your authorized KrelP dealer, distrib-
®.
utor, or Krell
KRELL® KAV-150a
English Page 7 of 12
Warranty
Krell® warrants this product to be free from
defects in material or workmanship for a
period of five years for circuitry and three
years for all mechanical components from
the original date of purchase. Should this
product fail to perform at any time during
the warranty, Krell® will repair it at no cost
to the owner, except as set forth in this
warranty. Transfer of warranty to a second
owner occurs automatically. Please contact Krell® to have the name on the war-
ranty changed. Transfer of warranty does
not extend the duration of the original war-
ranty period.
Note
This warranty does not apply to damage
caused by acts of God or nature.
The warranty period begins on the date of
retail purchase as noted on the retail sales
slip provided by an authorized Krell® deal-
er or distributor, or on the warranty regis-
tration card sent to Krell
an adequate proof of purchase date is
unavailable, the warranty period will begin
on the date the product was originally
shipped from the factory. The warranty
described in this paragraph shall be in lieu
of any other warranty, express or implied;
including, but not limited to, any implied
warranty of merchantability or fitness for a
particular purpose. There are no war-
ranties which exceed beyond those
described in this document. If this product
does not perform as warranted herein, the
owner’s sole remedy shall be repair. In no
event will Krell® be liable for incidental or
consequential damages arising from purchase, use, or inability to use this product,
even if Krell® has been advised of the pos-
sibility of such damages.
®.
In the event that
The warranty for this Krell® product is valid
only in the country to which the product
was originally shipped, through the autho-
rized Krell® distributor for that country, and
at the factory. There may be restrictions on
or changes to Krell’s warranty because of
regulations within a specific country.
Please check with your distributor for a
complete understanding of the warranty in
your country.
Freight to the factory is your responsibility.
Return freight within the United States
(U.S.A.) is included in the warranty. If you
have purchased your Krell® product out-
side the U.S.A. and wish to have it ser-
viced at the factory, all freight and associ-
ated charges to the factory are your
responsibility. Krell® will pay return freight
to the U.S.A.-based freight forwarder of
your choice. Freight and other charges to
ship the product from the freight forwarder
to you are also your responsibility.
The operating voltage of this product is
determined at the factory and can only be
changed by an authorized Krell® distributor
or at the factory. The voltage for this product in the U.S.A. cannot be changed for six
months from the original purchase date.
Any unauthorized voltage conversion,
disassembly, component replacement,
perforation of chassis, updates, or
modifications performed to the product
will void the warranty.
Page 8 of 12 English KRELL® KAV-150a
Return Authorization
Procedure
IMPORTANT
ff you believe there is a problem with your
component, please contact your dealer, distributor, or the Krell® factory to discuss the
problem before you return the component
for repair. To expedite service, you may
wish to complete and e-mail the Service
Request Form on our web site at:
ww~. krellon line. com
To return a product to Krell®, please fol-
low this procedure so that we may
serve you better:
1. Obtain a Return Authorization Number
(R/A number) and shipping address
from the Krell® Service Department.
Insure and accept all liability for loss or
2.
damage to the product during shipment
to the Krell® factory and prepay all shipping charges. The product may also be
hand delivered if arrangements with the
Service Department have been made in
advance. Proof of purchase may be re-
quired for warranty validation at the time
of hand delivery.
To purchase additional packaging,
®
please contact your authorized Krell
dealer, distributor, or the Krell® Service
Department for assistance.
Krell® is not responsible for any damage
incurred in transit. KrelP will file claims for
damages as necessary for products dam-
aged in transit to the factory. The owner is
responsible for filing claims for shipping dam-
ages that occur during the return shipment.
Replacement parts and/or products will be
furnished on an exchange basis only; any
parts and/or products returned to Krell® for
®.
exchange become the property of Krell
No expressed or implied warranty is made
for any Krell® product damaged by accident,
abuse, misuse, natural or personal disaster,
or unauthorized modification.
In the event that Krell® receives a product for
warranty service which has been modified in
any way without Krell® authorization, all warranties on that product will be void. The
product will be returned to original factory
layout specifications at the owner’s expense
before it is repaired. All repairs required after
the product has been returned to original
factory specification will be charged to the
customer, at current parts and labor rates.
Use the original packaging to insure the
3.
safe transit of the product to the factory,
dealer, or distributor. The use of any
packaging material other than the original
packaging materials is not recommend-
ed. KrelP may, at its discretion, return a
To contact the Krell Service De )artment
TEL 203-799-9954
Monday-Friday
9:00 am to 5:00 PM EST
FAX 203-799-9796
E-MAILkrell@ krellonline.com
product in new packaging and bill the
owner for such packaging if the product
received by Krell® was boxed in nonstandard packaging or if the original
packaging was so damaged that it was
unusable. If Krell® determines that new
packaging is required, the owner will be
KAV-150a
PRODUCT SERIALNUMBER
To register your product for warranty benefits,
complete and return the Warranty Registration
I
Card enclosed in the shipping box within 15 days
of purchase. Thank you.
notified before the product is returned.
KRELL® KAV-150a English Page 9 of 12
Krell® Industries, Inc.
45Connair Road
Orange, CT 06477-3650USA
TEL 203-799-9954 FAX 203-799-9796
E-MAIL krell@krelloniine.com
WEB SITE www.krellonline.com
Specifications
KAV-150a
Power Amplifier
FREQUENCY RESPONSE
20 Hz-20 kHz +0.0, -0.1 dB
.5 Hz-150 kHz +0.0, -3.0 dB
SIGNAL TO NOISE RATIO
112 dB, "A" weighted
DISTORTION
1 kHz 0.06% THD
20 kHz 0.25% THD
GAIN
25.8 dB
INPUT SENSITIVITY
1.8 Vrms
INPUT IMPENDENCE
100K Ohms
OUTPUT VOLTAGE
OUTPUT POWER, each channel driven
8 Ohms 600 W (bridged)
8 Ohms 150 W
4 Ohms 300 W
POWER CONSUMPTION
Idle 40 W
Max. 600 W
DIMENSIONS
19w x 3.7h x 15.5d in.
47.5w x 9.25h x 38.75d cm
WEIGHT
Shipped
Unit only
All operational features, functions, specifications, and
policies are subject to change without notification.
33 Ibs., 14.9 kg
25 Ibs., 1 1.4 kg
Peak to peak
RMS
116V
41 V
Loading...