Page 1
INSTALLATION MANUAL
www.kraususa.com I toll free: 1.800.775.0703 I © 2014-2015 Kraus USA Inc.
Seda™ 8” Widespread
2-Handle Faucet
FUS-1823
Page 2
Thank you for purchasing Kraus
We would like to take this opportunity to thank you for your business with Kraus
USA. It is our sincere hope that you are completely satised with your experience.
We welcome any questions or comments you may have, and will be glad to assist
you in the future.
For more information about Kraus products, please visit our website at:
www.kraususa.com
Please register your new Kraus product at the following web address in order to
activate the warranty and receive the full benet of customer support:
www.kraususa.com/registration
Sincerely,
Kraus Customer Service Department
Page 3
Prior to Installation:
• Make sure you have all necessary parts by checking the diagram and parts list. If
any part is missing or damaged, please contact Kraus Customer Service at 800-
775-0703 for a replacement
• Turn o the hot and cold water supply at the angle stops and turn on the old
faucet to release any built up pressure. Remove existing faucet. Clean sink or
countertop to remove any debris, plumber’s putty, or silicone
• Place bucket under angle stops. Turn on angle stops to ush any debris prior to
installing new plumbing. Shut o angle stops
• Max countertop thickness: 1 3/8”
Tools you will need:
Adjustable Wrench Phillips Screwdriver
Safety Goggles Bucket
7/8”
19.7
º
(22mm)
8 5/16”
1 1/4-18UNF-2A
(21mm)
10 1/8”
(257mm)
1 3/8”
(35mm)
Page 4
A
B
D
C1
C2
C3
C1
C2
C3
E1
E2
F
G
H
K
I
J
FUS-1823 Diagram and Parts List
A. Hot Handle Valve
B. Cold Handle Valve
C. Hot & Cold Handle Mounting
Hardware:
C1. Rubber & Metal Washer
C2. Mounting Nut
C3. Mounting Screws
D. Spout
E. Spout Mounting Hardware:
E1. Rubber & Metal U-Washer
E2. Mounting Nut
F. T-Union
G. Hot & Cold Waterlines
H. 3/8 in. OD x 1/2 in. IPS Waterlines
I. Aerator
J. Aerator Key
K. Hex Wrench
Page 5
4.92”
125mm
1.8”
46mm
2.24”
57mm
1.8”
46mm
4.92”
125mm
4.96”
126mm
5.62”
143mm
2.87”
73mm
4.76”
121mm
MAX 1.18”
30mm
Faucet Dimensions
Step 1: Remove mounting hardware and T-union
Remove T-union (F) and mounting
hardware (E) from spout (D).
Remove mounting hardware (C)
from hot and cold handle valves
(A & B)
1
2
3
1 1/4-18UNF-2A
A
D
D
A
C1
C2
C3
B
E1
E2
F
C
C
F
E
Page 6
Step 2: Install & secure spout
Install spout (D) through hole
in countertop or sink. Attach
rubber & metal U-washer (E1)
and mounting nut (E2). Adjust
spout (D) to proper position
and tighten mounting nut (E2)
with adjustable wrench. Secure
T-union (F) onto supply line of
spout (D). Tighten T-union (F)
with adjustable wrench
Step 3: Install & secure hot and cold handle valves
Install hot and cold handle valves
(A & B) through hole in countertop
or sink. Attach rubber & metal
washer (C1) and mounting nut
(C2) to the threaded mounting
pipe. From underneath the
countertop or sink, tighten
mounting nut (C2) onto valves (A
& B) with adjustable wrench until
snug. Secure mounting nut (C2) by
tightening mounting screws (C3)
with a Phillips head screwdriver
2
3
1 1/4-18UNF-2A
D
A
C1
C2
C3
E1
E2
F
B
3
1 1/4-18UNF-2A
A
C1
C2
C3
B
Page 7
Step 4: Connect waterlines to faucet and main valve
Step 5: Flush faucet
Secure hot & cold waterlines (G) to
hot and cold valves (A & B) (Hand-
Tighten Only). Thread other end
of waterlines to T-union (F). Attach
3/8 in. OD x 1/2 in. IPS waterlines
(H) to copper pipe on valves
A. Hot Side: Left
B. Cold Side: Right
Secure other end of waterlines to
angle stops. Tighten all ends with
adjustable wrench until snug. Turn
on angle stops and check for leaks
(DO NOT TURN FAUCET ON)
Remove adjustable aerator (I) with
aerator key (J). Turn water on for
1 minute to remove any debris.
Reassemble adjustable aerator (I)
3
1 1/4-18UNF-2A
4 5
H
D
A
C1
C2
C3
B
E1
E2
F
C
F
E
H
A
B
H
G
G
I
J
F
3
1 1/4-18UNF-2A
A
C1
C2
C3
B
I
J
Page 8
Replacement Part List - FVS-1823
4
1
3
6
5
10
18
8
7
9
16
13
17
12
19
2
11
15
14
1. Hot Handle
2. Cold Handle
3. Set Screw
4. Cover Button
5. Hot Cartridge
6. Hot Valve
7. Rubber & Metal Washer
8. Mounting Nut
9. Mounting Screw
10. Adjustable Aerator
11. Rubber & Metal U Washer
12. Mounting Nut
13. T-Union
14. Cold Cartridge
15. Cold Valve
16. Hot & Cold Waterlines
17. 3/8 in. OD x 1/2 in. IPS Waterlines
18. Aerator Key
19. Hex Wrench
Page 9
Trouble - Shooting
If you have followed the instructions carefully and your faucet still does not work
properly, take the following corrective steps:
PROBLEM CAUSE ACTION
Leakage under the
handle
Hot or cold cartridge (5
or 14) may be loose
Remove cover button
(4). Loosen set screw (3)
with hex wrench (19).
Remove handle (1 or
2). Tighten hot or cold
cartridge (5 or 14) with
adjustable wrench
Aerator drips or has
inconsistent water flow
pattern
Aerator (10) may be
dirty or not seated
properly
Unscrew aerator (10)
with aerator key (18).
Remove aerator (10)
and clean out debris
Water will not shut off
completely
Hot or cold cartridge (5
or 14) may need to be
adjusted or replaced
Remove cover button
(4). Loosen set screw
(3) with hex wrench
(19). Remove handle
(1 or 2). Remove hot or
cold cartridge (5 or 14)
with adjustable wrench.
Check for cracks
Care & Maintenance
*To keep the product clean & shining, follow the steps below:
1. Rinse with clean water & dry with a soft cloth
2. Do not clean with soaps, acid, polish, abrasives, or harsh cleaners
3. Do not use cloth with a coarse surface
4. Unscrew the aerator and clean when necessary
*This installation manual is subject to change without further notice.
Hot
Water
Cold
Water
Push
Page 10
Codes/Standards Applicable:
KRAUS LIMITED LIFETIME WARRANTY
This product has been manufactured and tested to the highest quality standards
by Kraus USA Inc. (“Kraus”). We offer our customers thoughtfully crafted fixtures
& accessories, engineered for enduring performance over years of use.
WHO IS COVERED BY THE WARRANTY
This warranty extends to the original purchaser only. This warranty is not
transferable, between homes or owners and is only applicable to residential use.
WHAT IS COVERED BY THE WARRANTY
Kraus warranties this product against defects due to material or craftsmanship
error during the warranty period: Kraus will provide replacement parts at
no charge, or at its option, replace any product or part of the product that is
deemed defective, under normal installation, use, service and maintenance. If
Kraus is unable to provide a replacement and repair is not practical or cannot
be made in timely fashion, Kraus may elect to refund the purchase price in
exchange for the return of the product.
CONDITIONS AND EXCLUSIONS
Like other home fixtures, Kraus products will require light maintenance to
ensure proper function. We provide you with complete knowledge to perform
this maintenance and can also recommend resources if you are unable to fulfill
this service.
A. Kraus will not be responsible for product failures due to lack of maintenance
or proper use. Please read your care and maintenance documentation to determine the limits of proper use.
B. The original sales receipt, order number, and/or proof of purchase must be
presented at the time of the warranty claim, without exception, for this warranty
to be applied to all Kraus products.
NSF/ANSI 372
NSF/ANSI 61
ASME A112.18.1M
1.5GPM 5.7L/min maximum
GREEN
Water Eciency
LEAD FREE
I
A
P
M
O
R
&
T
TM
Page 11
C. Kraus recommends installing all Kraus products with a licensed, professional
plumber. Kraus will not be held responsible for any damage or product failure
due to improper installation, misuse, or failure to use a licensed professional.
Please read your care and maintenance documentation to determine the limits
of proper use.
D. Commercial use will automatically void this warranty.
E. This warranty is not applicable to Kraus products purchased from an unau-
thorized seller. For a complete list of authorized sellers please visit http://www.
kraususa.com/where-to-buy.html
NONAPPLICABILITY OF THIS WARRANTY
By the purchase and use of our products, you agree that Kraus is not liable
for incidental, consequential or special damages associated with the return,
replacement, installation or use of your product. This includes freight costs,
cartridge replacement, labor, travel time, lost profit, home damages and other
contingent liabilities and costs (including, without limitation, costs associated
with experts, investigations, analyses, attorneys and other professionals and
services). The Kraus warranty is a comprehensive and explicit limit of liability,
and all items outside of it are not addressable by or the responsibility of
Kraus. Certain states have variances regarding implied warranties and in those
situations we remain fully compliant.
KRAUS USA Inc. makes no implication that products comply with any or all local
building or plumbing codes. It is the consumer’s responsibility to determine
local code compliance. This warranty extends to the original purchaser and first
consumer.
HELP LINE
For additional assistance at any point in the installation process, please call us at
1.800.775.0703 or email us at info@kraususa.com
Our customer service hours are Monday – Friday, 9am – 8pm EST.
Be sure to visit our website at www.kraususa.com
Page 12
www.kraususa.com
Loading...