Kraus Seda FUS-1821 Installation Manual

Download

Page 1

INSTALLATION MANUAL

Seda™ Single Lever Basin Faucet

FUS-1821

Page 2

Thank you for your purchase

We would like to take this opportunity to thank you for choosing Kraus. We hope that you are completely satised with your purchase, and enjoy it for years to come. If you have any questions, or require technical assistance, please contact us at 800.775.0703 and one of our representatives will be happy to help.

For more information about Kraus products, please visit:

www.kraususa.com

In order to activate your warranty and get faster access to customer support, please register your new Kraus product at:

www.kraususa.com/registration

Sincerely,

Kraus USA Customer Service

Page 3

Prior to Installation:

•

Make sure you have all necessary parts by checking the diagram and parts list. If

any part is missing or damaged, please contact Kraus Customer Service at 800-

775-0703 for a replacement

• Turn o the hot and cold water supply at the angle stops and turn on the old

faucet to release any built up pressure. Remove existing faucet. Clean sink or

countertop to remove any debris, plumber’s putty, or silicone

• Place bucket under angle stops. Turn on angle stops to ush any debris prior to

installing new plumbing. Shut o angle stops

• Pre-drilled hole size requirement: 1 3/8” (min)

• Max countertop thickness: 1 3/8”

Tools you will need:

Adjustable Wrench Phillips Screwdriver

Safety Goggles Bucket

3/8”

(10mm)

7/8”

19.7

(22mm)

8 5/16”

1 1/4-18UNF-2A

(21mm)

10 1/8”

(257mm)

1 3/8”

(35mm)

3 3/4”

(96mm)

For technical assistance or replacement parts, please contact Kraus

Customer Service and one of our representatives will be happy to help:

Toll-Free: 800-775-0703 or Customerservice@kraususa.com

Page 4

C3 C4

Diagram and Parts List

A. Faucet Body

B. Base O-Ring (factory-installed)

C. Mounting Hardware:

C1. Rubber U-Washer

C2. Metal U-Washer

C3. Mounting Screw

C4. Mounting Nut

D. Hot & Cold Waterlines

E. Adjustable Aerator

F. Aerator Key

G. Hex Wrench

Page 5

7.2”

183mm

5”

127mm

2.4”

61mm

5.03” 128mm

6.8” 173mm

6”

152mm

1.37”

35 mm

1.37”

35 mm

1.37” MAX

35 mm

Faucet Dimensions

Page 6

l m

a. Waste Stopper

b. Drain

c. Rubber Washer

d. Concave Washer

e. Plastic Washer

f. Mounting Nut

g. Tailpipe Washer

h. Tailpipe

i. Top Hat Washer

j. Drain Off Pole

k. Washer

l. Retaining Nut

m. Extender Rod

n. Clip

o. Thumb Screw

p. Lift Pole

Lift Rod Drain Diagram and Parts List and Dimensions

Page 7

Step 1: Remove mounting hardware and install waterlines

Remove faucet, mounting

hardware, and waterlines from

the box. Remove mounting nut

(C4) from mounting screw (C3).

Place faucet body (A) on a soft

cloth, spout facing up. Secure

hot & cold waterlines (D) at the

base of the faucet (hand-tighten,

then secure with ¼ turn of

adjustable wrench)

A. Hot Side: Left

B. Cold Side: Right

Thread mounting screw (C3)

into faucet base, at head up,

and tighten with a Phillips head

screwdriver until snug

Step 2: Install faucet

Install faucet body (A) through 1

3/8” hole in countertop or sink,

with base O-ring (B), hot & cold

waterlines (D), and mounting

screw (C3) attached

9/16”-18UNEF

27mm ~ 41.3mm

1 1/16” ~ 1 5/8”

(42.5 mm Max)

C1 C2

9/16”-18UNEF

27mm ~ 41.3mm

1 1/16” ~ 1 5/8”

(42.5 mm Max)

C1 C2

Page 8

Step 3: Secure faucet

Install rubber U-washer (C1)

and metal U-washer (C2) from

underneath the countertop or

sink. Attach mounting nut (C4) to

mounting screw (C3) and tighten

with adjustable wrench or 10mm

wrench until snug

Step 4: Connect waterlines to main valve

Thread hot & cold waterlines (D)

onto angle stops and tighten with

adjustable wrench until snug. Turn

on angle stops and check for leaks

(DO NOT TURN FAUCET ON)

9/16”-18UNEF

27mm ~ 41.3mm

1 1/16” ~ 1 5/8”

(42.5 mm Max)

C1 C2

Step 5: Install Drain

e f g

e f

• Remove waste stopper (a) from

drain (b). Remove tail pipe (h), mounting nut (f), plastic washer (e), and concave washer (d) from drain (b). Remove retaining nut (l)

and washer (k) from tailpipe (h)

Installer tip: Leave top hat washer (g) in tailpipe (h)

Page 9

Step 5: Install Drain

e f

• Install drain (b), with rubber

washer (c) attached, into the drain hole. Attach concave washer (d) with narrow end up, plastic washer (e), and mounting nut (f) to drain (b) from underneath countertop or sink. Secure tightly to sink with an adjustable wrench

• Thread tailpipe (h) onto drain (b)

and hand-tighten. Adjust tailpipe (h) so drain o pole opening is to the rear of the sink

Installer Tip: Make sure tailpipe washer (g) is installed in tailpipe (h)

• Insert waste stopper (a) into

drain (b). Make sure slot at end of waste stopper (a) is facing the

rear of the sink

Page 10

Step 5: Install Drain

e f

• Insert lift pole rod (p) through the

hole in the back of the faucet body. Loosen thumb screw (o) and attach extender rod (m) to lift pole rod (p).

Tighten thumb screw (o)

• Insert shortest end of drain o

pole (j) into drain o pole opening of tailpipe (h). Make sure drain o pole (j) and slot on waste stopper (a) engage. Attach washer (k) and retaining nut (l) through drain o pole (j). Secure retaining nut (l) to drain o pole opening of tailpipe (h)

• Place one end of clip (n) on drain

o pole (j). Insert drain o pole (j) through desired hole of extender rod (m). Place other end of clip (n)

on drain o pole (j)

Installer Tip: You may adjust the extender rod (m) to a desired height

Page 11

Step6: Flush faucet

Remove adjustable aerator (E)

with aerator key (F). Turn water on

for 1 minute to remove any debris.

Reassemble aerator (E) and adjust

to desired position

Replacement Part List - FUS-1821

6 7

1. Metal Handle

2. Set Screw

3. Cartridge Cover

4. Cartridge Sleeve

5. Metal O-Ring

6. Rubber Washer

7. Locking Nut

8. Cartridge

9. Base O-Ring

10. Rubber U-Washer

11. Metal U-Washer

12. Mounting Nut

13. Mounting Screw

14. Adjustable Aerator

15. Aerator Key

16. Hot & Cold Waterlines

17. Hex Wrench

Page 12

1. Waste Stopper

2. Drain

3. Rubber Washer

4. Concave Washer

5. Plastic Washer

6. Mounting Nut

7. Tailpipe Washer

8. Tailpipe

9. Top Hat Washer

10. Drain Off Pole

11. Washer

12. Retaining Nut

13. Extender Rod

14. Clip

15. Thumb Screw

16. Lift Pole Rod

Replacement Part List - Lift Rod Drain

12 13

Download the Kraus Care & Maintenance Guide at:

http://www.kraususa.com/maintenance

Page 13

Trouble - Shooting

If you have followed the instructions carefully and your faucet still does not work

properly, take the following corrective steps:

PROBLEM CAUSE ACTION

Leakage under the handle Locking nut (7) has come

loose

Loosen set screw (2) with hex wrench (17). Remove metal handle (1), cartridge cover (3), cartridge sleeve (4), metal o-ring (5) & rubber washer (6). Tighten locking nut (7) with wrench

Aerator drips or has inconsistent water flow pattern

Aerator (14) may be dirty or not seated properly

Unscrew aerator (14) with aerator key (15). Remove aerator (14) and clean out debris

Drain is leaking Washers may be

compromised or installed incorrectly

Check washers to make sure they are installed correctly and not cracked

Water will not shut off completely

Cartridge(8) may need to be adjusted or replaced

Loosen set screw (2) with hex wrench (17). Remove metal handle (1), cartridge cover (3), cartridge sleeve (4), metal o-ring (5) & rubber washer (6). Unscrew locking nut (7) with wrench. Remove cartridge (8). Check for cracks

Care & Maintenance

*To keep the product clean & shining, follow the steps below:

1. Rinse with clean water & dry with a soft cloth

2. Do not clean with soaps, acid, polish, abrasives, or harsh cleaners

3. Do not use cloth with a coarse surface

4. Unscrew the aerator and clean when necessary

*This installation manual is subject to change without further notice.

Hot Water

Cold Water

Push

Page 14

Codes/Standards Applicable:

NSF/ANSI 372

NSF/ANSI 61

ASME A112.18.1M

1.2GPM 4.5L/min maximum

GREEN

Water Eciency

LEAD FREE

HELP LINE

Our customer service hours are Monday – Friday, 9am – 8pm EST. Be sure to visit our website at www.kraususa.com

If you are a homeowner please contact a Kraus Customer Service Representative at:

Kraus USA, Inc. 12 Harbor Park Drive Port Washington, NY 11050 Toll-free 800-775-0703 Customerservice@kraususa.com

If you are a plumbing contractor or trade professional please contact a Kraus Pro Representative at:

Kraus USA, Inc. 12 Harbor Park Drive Port Washington, NY 11050 516-801-8955 Proservice@kraususa.com

If you are an Authorized Partner please contact a Partner Support Representative at:

Kraus USA, Inc. 12 Harbor Park Drive Port Washington, NY 11050 516-801-8954 Partnersupport@kraususa.com

In requesting warranty service, please be ready to provide:

1. Proof of purchase.

2. A description of the problem.

Page 15

www.kraususa.com

Page 16

Receive Proof of Ownership

Access Customer Care & Installation Help

Get Exclusive Kraus Oers & Promotions

Scan to Register Online

or visit http://www.kraususa.com/registration

Please take a moment to share your experience.

Visit http://www.kraususa.com/review to let us know what you think

about your new Kraus product.

1.800.775.0703 / www.kraususa.com / customerservice@kraususa.com

Like & Follow KrausUSA

Download the Kraus Care & Maintenance Guide at:

http://www.kraususa.com/maintenance

www.kraususa.com

We’re always looking for ways to improve.