Page 1
INSTALLATION MANUAL
www.kraususa.com I toll free: 1.800.775.0703 I © 2013-2014 Kraus USA Inc.
KPF-1621
Single Lever Pull-Out Kitchen Faucet
Page 2
Congratulations on your new Kraus purchase!
We would like to take this opportunity to thank you for your business with Kraus USA.
It is our sincere hope that you are completely satised with your Kraus experience.
We welcome any questions or comments you may have, and look forward to assisting
you in the future.
For more information about Kraus products, please visit our website at:
www.kraususa.com.
In order to allow us to serve you better, we recommend registering your new Kraus
product at: www.kraususa.com/product-registration
Sincerely,
Kraus Customer Service Department
Page 3
Prior to Installation
•
Make sure that cold and hot water lines are turned o
• Wrap all threaded connections with Teon tape. Always wrap in a clockwise
direction
• Cover your drain to avoid losing parts
• Do not disassemble the main faucet body, as it has been installed &
commissioned correctly & precisely before delivery from the factory
• To keep the faucet from jamming, ush the water pipe before installation
• Using condition: Working pressure at 0.05-1.0MPa (including cold & hot
water pressure) with applicable water temperature: 4C-90C
• After installation, make sure every joint is safely sealed and that there is no
leaking
• Make sure to correct the hot/cold inlet pipe correctly: if facing faucet, hot
water pipe connects on the left and cold water pipe connects on the right
Page 4
Included Parts:
1. Faucet Body
2. Base O-Ring
3. Rubber Washer
4. Metal Washer
5. Mounting Nut
6. Mounting Screws (2)
7. Weight
8. Spray Head
9. Spray Hose
10. Hot and Cold Waterlines (2)
11. Manual
KPF-1621 Diagram and Parts List
9
8
7
2
3
4
5
6
7
11
10
1
11
15
15
Wrench Phillips Screwdriver
Tools you will need:
Page 5
Dimension Drawings
249
11 9/16”
20°
231
Ø35~Ø38
Ø3/8”~Ø1 1/2”
Hot
Water
Cold
Water
475
18 3/4”
Max35
Max1 3/8”
9 3/32”
Safety Tips
•
If soldering the water connections when installing the faucet, remove the O-rings,
cartridges, and washers before applying any heat
• Protect your eyes with safety glasses when cutting or soldering
Page 6
475
18 3/4”
Max35
Max1 3/8”
Dimension Drawings
Safety Tips
•
Do not overtighten xing screws/nuts. Tighten nger-tight, then use a wrench/
screwdriver to tighten the xing screw/nut until snug
Page 7
Installation Method 1
Faucet Installation Methods
The minimum distance between the
faucet hole and the wall should be 3.5”
Minimum distance 3.5”
Less than 3.5”
30˚
Less than 3.5”
30˚
Installation Method 2
If the distance between the faucet hole
and the wall is less than 3.5”, position the
faucet lever 30 degrees to 90 degrees off
of the wall to allow for full operation
Page 8
Step 2
Connect spray head (8) to spray hose (9) and tighten rmly. Insert the faucet body
(1) into the hole on the deck with the base o-ring (2), and then install the rubber
washer (3), metal washer (4), mounting nut (5) and mounting screws (6) from
underneath the sink
1
Ø35~Ø38
Ø1 3/8”~Ø1 1/2”
2
3
4
5
6
1
2
3
4
5
6
9
8
9
8
1
Ø35~Ø38
Ø1 3/8”~Ø1 1/2”
2
3
4
5
6
Step 1
Remove mounting screws (6),
mounting nut (5), metal washer
(4), and rubber washer (3) from the
faucet body (1)
Faucet Installation Steps
Page 9
5
6
join
hose
Cold
Water
Hot
Water
Step 3
After adjusting the direction of
the faucet body(1), tighten the
mounting nut (5) until snug and
tighten the mounting screws (6)
to the nut with a Philips head
screwdriver
Step 4
Connect the spray hose (9) to
the supply line and tighten with
a wrench until snug, then install
the weight (7) at the lowest point
(horizontally) on the spray hose (9)
7
join
hose
Cold
Water
Hot
Water
Page 10
Step 5
Connect hot and cold waterlines (10) to the angle stops and tighten with
a wrench until snug, then unscrew spray head (8), hold the tip of the spray
hose (9) and turn on the faucet to ush any debris
Page 11
1. Pull the lever to the right
to turn on the water. Push to
the left to turn o
2. Pull the lever forward
to increase hot water ow
and push the lever back to
increase the cold water ow
5
7
6
join
hose
Cold
Water
Hot
Water
7
join
hose
Cold
Water
Hot
Water
Usage
How to Operate the Handle
Page 12
Care & Maintenance
*To keep the product clean & shining, follow the steps below:
1. Rinse clean with water & dry with a soft cloth
2. Do not clean with soaps, acid, polish, abrasives,
or harsh cleaners
3. Do not use cloth with a coarse surface
4. Unscrew the aerator and clean when necessary
*This installation manual is subject to change without further notice
Hot
Water
Cold
Water
Push
Page 13
Leakage under the
handle
Locking nut has come
loose
Remove the index
button at the top of
the handle. Loosen
set screw with a hex
wrench. Remove the
handle and unscrew
trim cap by hand.
Tighten locking nut
with an adjustable
wrench
Trouble - Shooting
If you have followed the instructions carefully and your faucet still does not
work properly, take the following corrective steps:
PROBLEM CAUSE ACTION
Water will not shut off
completely
Cartridge may be
defective
Remove the index
button at the top of
the handle. Loosen
set screw with a hex
wrench. Remove the
handle and unscrew
trim cap by hand.
Unscrew the locking
nut with an adjustable
wrench. Remove
ceramic disc cartridge.
Check for cracks
Leaking between spray
head and the hose
Spray head may be
loose or washer is not
seated correctly in the
hose connection
Tighten the spray head
by hand until snug.
Make sure the washer is
seated correctly
Page 14
Codes/Standards Applicable:
Specied model meets or exceeds the following: ANSI/ASME A112.18.1, cUPC,
AB1953
KRAUS LIMITED LIFETIME WARRANTY
This product has been manufactured and tested to the highest quality standards
by Kraus USA Inc. (“Kraus”). We offer our customers thoughtfully crafted fixtures
& accessories, engineered for enduring performance over years of use.
WHO IS COVERED BY THE WARRANTY
This warranty extends to the original purchaser only. This warranty is not
transferable, between homes or owners and is only applicable to residential use.
WHAT IS COVERED BY THE WARRANTY
Kraus warranties this product against defects due to material or craftsmanship
error during the warranty period: Kraus will provide replacement parts at
no charge, or at its option, replace any product or part of the product that is
deemed defective, under normal installation, use, service and maintenance. If
Kraus is unable to provide a replacement and repair is not practical or cannot
be made in timely fashion, Kraus may elect to refund the purchase price in
exchange for the return of the product.
CONDITIONS AND EXCLUSIONS
Like other home fixtures, Kraus products will require light maintenance to
ensure proper function. We provide you with complete knowledge to perform
this maintenance and can also recommend resources if you are unable to fulfill
this service.
A. Kraus will not be responsible for product failures due to lack of maintenance
or proper use. Please read your care and maintenance documentation to determine the limits of proper use.
B. The original sales receipt, order number, and/or proof of purchase must be
presented at the time of the warranty claim, without exception, for this warranty
to be applied to all Kraus products.
Page 15
C. Kraus recommends installing all Kraus products with a licensed, professional
plumber. Kraus will not be held responsible for any damage or product failure
due to improper installation, misuse, or failure to use a licensed professional.
Please read your care and maintenance documentation to determine the limits
of proper use.
D. Commercial use will automatically void this warranty.
E. This warranty is not applicable to Kraus products purchased from an unau-
thorized seller. For a complete list of authorized sellers please visit http://www.
kraususa.com/where-to-buy.html
NONAPPLICABILITY OF THIS WARRANTY
By the purchase and use of our products, you agree that Kraus is not liable
for incidental, consequential or special damages associated with the return,
replacement, installation or use of your product. This includes freight costs,
cartridge replacement, labor, travel time, lost profit, home damages and other
contingent liabilities and costs (including, without limitation, costs associated
with experts, investigations, analyses, attorneys and other professionals and
services). The Kraus warranty is a comprehensive and explicit limit of liability,
and all items outside of it are not addressable by or the responsibility of
Kraus. Certain states have variances regarding implied warranties and in those
situations we remain fully compliant.
KRAUS USA Inc. makes no implication that products comply with any or all local
building or plumbing codes. It is the consumer’s responsibility to determine
local code compliance. This warranty extends to the original purchaser and first
consumer.
HELP LINE
For additional assistance at any point in the installation process, please call us at
1.800.775.0703 or email us at info@kraususa.com
Our customer service hours are Monday – Friday, 9am – 8pm EST.
Be sure to visit our website at www.kraususa.com.
Page 16
www.kraususa.com
Loading...