Kraus KCA-1102 Installation Manual
KCA-1102
All-In-One
Kitchen Set
www.kraususa.com I Toll Free: 1.800.775.0703 I © 2018 Kraus USA Inc. I REV. December 10, 2018
Congratulations on the purchase of your new
Kraus plumbing fixture!
Please keep the box and packaging materials until your product is
completely installed. If you have any questions, require technical
assistance or have any problems with your product:
2
Please contact our Customer Service Team
1-800-775-0703 / customerservice@kraususa.com
Have the model number available and retain a copy of your receipt
with purchase date for reference.
If for any reason this product does not meet your expectations,
please be sure to repack this product in the original box and
packaging material to avoid damage during transit.
3
Make sure to check off that you have all of the following items
Prior to Installation:
· Make sure you have all necessary parts by checking the diagram and parts list. If any part is missing or
damaged, please contact Kraus Customer Service at 800-775-0703 for a replacement.
· Turn off the cold and hot water at the angle stops and turn on the old faucet to release and built up pressure
· Flush angle stops to release any debris prior to installation
· Pre-drilled hole size requirement: 1 3/8" (min) - 1 1/2" (max)
· Max countertop thickness: 1 3/4"
Kitchen Sink - KHT400-33
Kitchen Faucet - KPF-1610SS
Cut-Out Template
Undermounting Hardware
Top Mount Hardware
Bottom Grid - KBG-T400-33
Drain - ST-1
4
Tools you will need:
4
NOTE: Specialized tools may be necessary to install Kraus Stainless Steel Kitchen
sinks with countertop materials other than wood, marble or granite.
Phillips Screwdriver Pencil
Tape Measure
Putty Knife
Safety Goggles
Silicone Adhesive
Jig Saw
Drill
Scissors
Screwdriver
55
Model #: KHT400-33
Sink Dimensions: 33” x 22” x 9”
Min Cabinet Size: 36”
Matching Grid: KBG-T400-33
Drain Model #: ST-1
Dimensions:
33"
(838.2mm)
30 1/2"
(774.7mm)
22"
(558.8mm)
17"
(431.8mm)
3 1/2"
(90mm)
1 3/8"
(35mm)
3 1/2"
(88.9mm)
2"
(50.8mm)
4 1/2"
(114.3mm)
1 1/4"
(31.8mm)
3/8"
(10mm)
9"
(228.6mm)
3/8"
(10mm)
66
Topmount Installation
Step 1. Position Template
· Check the cut-out template against the actual sink to ensure a proper
sized cut-out.
· Place the cut-out template in the desired location on the countertop.
NOTE: Make sure clearance is suitable for backsplash, faucet and plumbing for the sink.
Step 2. Trace Template
· Trace template on countertop with a pencil.
Paper Template
Paper Template
7
Step 3. Cut Countertop
· Cut the opening in the countertop by carefully following the traced line.
NOTE: Please use the appropriate saw that best fits your countertop material.
8
Step 4. Attach Mounting Hardware
· Attach mounting hardware to the prongs protruding from the underside of the sink rim.
· Make sure the hooked side of the mounting clip is facing away from the sink.
Insert
9
Step 5. Apply Silicone or Plumber's Putty
· Clean and dry the surface around the opening of the sink.
· Turn the unit upside down to apply sealant. Apply silicone-based sealant (not included) underneath the edge of the
sink.
Loading...